HLINS YA 581 Shock Absorber for Yamaha Tracer 9 Instruction Manual

June 4, 2024
HLINS

YA 581 Shock Absorber
for Yamaha Tracer 9
Instruction Manual

YA 581 Shock Absorber for Yamaha Tracer 9


HLINS YA 581 Shock Absorber for Yamaha Tracer 9

Note!
Please note that there can be small differences between your product and the images in these instructions.
Note!
Please note that during storage and transport, especially at high ambient temperatures, some of the oil and grease used for assembly may leak and stain the packaging. This will not cause damage to the product, wipe off the excess oil or grease with a cloth.

Note!
Before you install this product, check the kit contents. If anything is missing, please contact an Öhlins dealer.
 Warning!
Before you install this product, read the Öhlins Owner’s manual. This product is an important part of the vehicle and the vehicle’s stability.

⚠ Warning!
We strongly recommend letting an Öhlins dealer install this product.
⚠ Warning!
If you work with a lifted vehicle, make sure that it is safely supported to prevent it from tipping over.
Note!
When you work with this product, see the vehicle service manual for vehicle- specific procedures and important data.
Note!
Before you install this product clean the vehicle.

  1. Put the motorcycle on a work stand so that the rear wheel barely touches the ground.
  2. Remove the front shock absorber attachment screw.
  3. Remove the rear shock absorber attachment screw. Remove the original shock absorber.
  4. Install the shock absorber with the valve down, and the hose on the left side led towards the back of the vehicle (see figure). Install the rear shock absorber attachment first.
  5. Install the front shock absorber attachment screw.
  6. Remove the left passenger foot peg. Mount the supplied bracket between the foot peg and the frame (see figure).
  7. Install the pre-load adjuster according to the figure. Use the supplied M6x30 screws (05404‑07), washers (00153‑04), and nuts (00430‑02). Apply thread lock on the thread.
  8. Fasten the hose with cable ties if necessary.
    Make sure that the hose runs without sharp bends and that the hose is not squeezed when the rear suspension is compressed or extended.
    HLINS YA 581 Shock Absorber for Yamaha Tracer 9 - MOUNTING
INSTRUCTIONS

ADJUSTMENTS

⚠ Warning!
Before you ride/drive, always make sure that the setup is according to the recommended setup data. Read about adjustments and set up in the Öhlins Owner’s Manual before you make any adjustments. Contact an Öhlins dealer if you have any questions about setting up.

HLINS YA 581 Shock Absorber for Yamaha Tracer 9 -
ADJUSTMENTS

SETUP DATA

Length 327 mm
Stroke 71.5 mm
Rebound 16 clicks
Spring preload 9 mm
Spring 01096-41
Spring rate 115 N/mm
Spring free length 190 mm

Öhlins products are subject to continuous improvement and development, therefore, although these instructions include the most up-to-date information available at the time of printing, minor updates may occur.
© Öhlins Racing AB. All rights reserved. Any reprinting or unauthorized use without the written permission of Öhlins Racing AB is prohibited.
To find the latest information contact an Öhlins distributor.
Please contact Öhlins if you have any questions regarding the contents of this document.

Öhlins Racing AB
Box 722
S-194 27 Upplands Väsby, Sweden
Phone +46 8 590 025 00
fax +46 8 590 025 80
Part no. MI_YA581_0
Issued 2021-11-11
WWW.OHLINS.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals