CRUX SWRNS-63N Radio Replacement with Steering Wheel Control Retention Instruction Manual
- June 13, 2024
- CRUX
Table of Contents
SWRNS-63N
Radio Replacement with Steering Wheel Control Retention
for Select 2012-2019 NISSAN Vehicles w/ Navigation
PRODUCT FEATURES:
-Retains factory features in select Nissan vehicles while functioning with an aftermarket radio.
– Pre-programmed to retain factory Medium Speed CAN-Data Bus Steering Wheel
Controls.
– Includes antenna adapter
– Retains Bose Amplifier system.
– Retains factory auxilary input
– Retains factory camera (not 360 panoramic camera)
– Retains factory USB input
– Provides Reverse Gear Output
PARTS INCLUDED:
INSTALLATION DIAGRAM FOR AMPLIFIED VEHICLES:
INSTALLATION DIAGRAM FOR NON-AMPLIFIED VEHICLES:
** ACC
Power Output Note: For vehicles equipped with intellegent key systems (Push
Start Button)
+12 V accessory red wire may not activate radio, must use ignition power
output (Red/Black wire) instead.
- For Non-Amplified systems please cut RCA , and mate colored wires to the appropriate aftermarket radio speaker wires
DIP SWITCH SETTINGS:
AFTERMARKET RADIO DIP SWITCH SETTINGS:
| RADIO BRAND: DIP#: | 1 | 2 | 3 |
|---|---|---|---|
| Atoto, Dual, Fahrenheit, Jensen, Nakamichi, | OFF | ON | ON |
| Pioneer, Power Acoustik, Soundstream | OFF | ON | ON |
| Blaupunkt,Most off brand Radio | OFF | ON | ON |
| Alpine | OFF | OFF | OFF |
| Clarion, Stinger | ON | ON | OFF |
| Kenwood | ON | ON | ON |
| JVC | ON | OFF | ON |
| Boss, Old Sony | ON | OFF | OFF |
| New Sony (with CarPlay) | OFF | ON | OFF |
4-PIN SWC CABLE
Use the proper 3.5MM to 4-Pin SWC cable for the aftermarket radio you are
using.
OPTION A is used for ALPINE, CLARION, JVC, and KENWOOD units (Blue/Yellow wire
is attached)
OPTION B is used for ATOTO, BLAUPUNKT, BOSS, DUAL, FARENHEIT, JENSEN, POWER
ACOUSTIK,
PIONEER, SONY, SOUNDSTREAM and Most Off-Brand Radios.
NOTE: Cap or insulate the 3.5mm plug or Blue/Yellow wire if not being
used.
For aftermarket radios that have wires for SWC connections, cut off the 3.5mm
plug on the Crux SWC Cable (option 8) and connect the SWC wires as follows:
Note that there are some radios that only have SWC1 and SWC2Z, in this case
“shield” does not need to be connected.
VEHICLE APPLICATIONS:
Compatible nissan Vehicles
NISSAN
2013 – 2017 Altima w/ Bose and w/ Nav
2013 – 2017 Altima w/o Bose and w/ Nav
2014 – 2016 Rogue w/ Bose and w/ Nav
2014 – 2016 Rogue w/o Bose and w/ Nav
2017 – 2018 Sentra w/ Bose and w/ Nav
2017 – 2018 Sentra w/o Bose and w/ Nav
2012 – 2019 Versa w/ Nav
NOTE: Some SWC functions might not be
retained for the following radio series:
Planet Audio P9900CPA, Jensen CAR 710, Atoto F7, and similar radios of these
brands.
DIP switch settings for Pioneer receivers: 
Location of the switch may vary on
the Interface (Comer or Middle).
Please note that interfaces with DIP at the end of the LOT# are installed with
the switch.
- Set DIP switch to “3V3” position for support of NEW generation Pioneer steering wheel button control.
- Set DIP switch to “5V” position for support of OLD generation Pioneer steering wheel button control.
Crux Interfacing Solutions
Chatsworth, CA 91311
phone: 818-609-9299
fax: 818-996-8188
www.cruxinterfacing.com
rev.230122
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>