CRUX SOOCR-26 Wiring Interface Connect New Car Stereo Retain The Factory Amp Instruction Manual
- June 1, 2024
- CRUX
Table of Contents
- CRUX SOOCR-26 Wiring Interface Connect New Car Stereo Retain The Factory
- Product Information
- Product Usage Instructions
- FAQ
- PRODUCT FEATURES
- PARTS INCLUDED
- INSTALLATION DIAGRAM
- FOR 4.3″ AND 8.4″ SCREEN REPLACEMENT
- VEHICLE APPLICATIONS
- ABOUT COMPANY
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CRUX SOOCR-26 Wiring Interface Connect New Car Stereo Retain The Factory
Amp
Product Information
Specifications:
- Product Name: SOOCR-26 Radio Replacement Module
- Compatibility: CHRYSLER, DODGE, and JEEP Vehicles
- Features: Does not retain Steering Wheel Controls, provides reverse trigger for rear view camera, EIA color coded wiring
Product Usage Instructions
Installation:
The SOOCR-26 includes harnesses for older and newer model vehicles. Follow
the installation diagrams provided for each harness type.
- 1st Generation Harness:
- Connect VSS, Illumination (+), Antenna/Amp Turn on, Reverse Trigger, +12V Constant, +12V ACC, and Ground wires according to the color codes.
- For amplified and non-amplified systems, refer to the provided Audio Filter and 12-Pin Black Connector.
- 2nd Generation Harness:
- Similar connections as the 1st Generation Harness with isolated Constant & Ground Pins.
- For amplified systems, connect the 4-pin Molex connector to the AMPLIFIED plug on the SOOCR-26 Harness.
AND 8.4 Screen Replacement:
When replacing the radio with a 4.3 or 8.4 screen, tap into the CAN signals
along with Power, Ground, and Speakers from the factory White 22-Pin
connector.
Troubleshooting:
If using an aftermarket radio, ensure proper connection of the rear
SOOCR-26 speakers to the front speakers of the aftermarket radio to avoid
Bluetooth audio issues.
FAQ
-
Does the SOOCR-26 support vehicles with Steering Wheel Controls?
No, it does not retain Steering Wheel Controls. For vehicles with Steering Wheel Controls, use part# SWRCR-59. -
How do I connect a rear view camera for my vehicle?
The SOOCR-26 provides a reverse trigger for rear view cameras. Connect the reverse trigger wire from the aftermarket radio and/or camera power to the factory reverse light wire instead.
PRODUCT FEATURES
- Retains factory features in select Chrysler, Dodge and Jeep vehicles while functioning with an aftermarket radio.
- Does not retain Steering Wheel Controls.
- Supports amplified and non-amplified systems.
- Provides reverse trigger for rear view camera.
- EIA color coded wiring for easy installation
NOTES:
- The Front and Rear fading are NON-Adjustable on amplified systems.
- Also supports radio replacement in vehicles with 4.3″ and 8.4″ color screens.
- If vehicle is equipped with Steering Wheel Controls use part# SWRCR-59
- If you require a dash kit with SWC interface use part# DKCR-59K
PARTS INCLUDED
INSTALLATION DIAGRAM
The SOOCR-26 includes 2 harnesses for older and new model vehicles.
See installation diagrams below for each harness.
1st Generation Harness
2nd Generation Harness
Speaker wire connections:
Wire the audio filter using the connection chart below. Plug the 4 pin Molex
plug found on the 1st or 2nd generation harness to the corresponding 4 pin
Molex socket on the audio filter. (Amplified or Non-Amplified)
| NON AMPLIFIED SYSTEMS | AMPLIFIED SYSTEMS |
|---|
Plug the 4-pin Molex connector to the NON-AMPLIFIED
| Plug the 4-pin Molex connector to the AMPLIFIED
Wire Connections| Wire Connections:
Aftermarket Radio| SOOCR-26 Harness| Aftermarket Radio| SOOCR-26 Harness
White| White| White| Green
White/Black| White/Black| White/Black| Green/Black
Gray| Gray| Gray| Purple
Gray/Black| Gray/Black| Gray/Black| Purple/Black
Green| Green| Green| Not Used
Green/Black| Green/Black| Green/Black| Not Used
Purple| Purple| Purple| Not Used
Purple/Black| Purple/Black| Purple/Black| Not Used
Amplified vehicle troubleshooting:
Bluetooth may be inaudible when installing select aftermarket radios.
Therefore hook the rear SOOCR-26 speakers to the aftermarket radio front
speakers.
FOR 4.3″ AND 8.4″ SCREEN REPLACEMENT
When replacing the radio with a 4.3″ OR 8.4″ screen, you will need to tap the CAN signals along with Power, Ground, and Speakers from the factory White 22-Pin connector. Tap the wires as shown below Again, these connections are made on the factory White 22-pin connector.
VEHICLE APPLICATIONS
ABOUT COMPANY
- Crux Interfacing Solutions
- 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
- phone: 818-609-9299
- fax: 818-996-8188
- www.cruxinterfacing.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>