CREWORKS V20221214 Multifunctional Heat Press Machine Instruction Manual

V20221214
SWING-AWAY HEAT PRESS
INSTRUCTION MANUAL

Read Carefully Before Use
Keep for Future Reference

SAFETY INFORMATION

Warning!

• When used properly, this device is safe and user friendly. However, it has the potential to cause severe burns and fires when used incorrectly. Read these instructions carefully before use.
  Provide them to any other users and provide them with this device if it is ever given or sold to a third party. Failure to do so may result in fires, electric shock, serious property damage, and serious personal injury.

• ONLY use this product for its intended purpose, using heat to transfer designs onto fabric, ceramic, and similar materials. Never use this device for preparation or decoration of food for human or animal consumption.

• DO NOT allow use by children, by anyone who has not read these instructions, or by any person whose mental or physical condition might prevent safe use. Do not use this device when tired or while under the influence of drugs, alcohol, or strong medication.

• ONLY use this device with stable, compatible, and grounded power sources. Never use it with extension cords of insufficient gauge to handle the expected electrical load. Always ensure all plugs are securely fastened, all power cords are undamaged, and the device is protected against any possible surge along the line. In standard residential and commercial settings, do not add other devices on the same circuit being used by this device.

• DO NOT adjust this device’s electrical components or allow them to become wet. Do not use it with wet hands or in highly humid environments. If this device develops condensation from temperature or elevation change or ever accidentally becomes wet, leave it disconnected from power until it has completely dried. Discontinue use until it is serviced by a trained technician if any malfunction occurs.

• NEVER use or store this device around highly flammable or explosive substances or gases.

• ALWAYS adjust the temperature and time parameters appropriately for different materials. Research your material BEFORE use and avoid any that won’t be able to withstand the prolonged high temperatures of the transfer process. Be EXTREMELY careful with glass.

• ALWAYS be careful not to confuse the device’s Fahrenheit and Celsius settings.

• Post the number of the local fire department and keep a fire extinguisher nearby in case of accidents. Inform any users of their locations.

• ALWAYS prepare the heat resistant mats before beginning work. Bring your platen up to heat before pressing the transfer down or closed.

• NEVER leave this device unattended during use. Someone should always be available to respond quickly to any accidents or emergencies that might occur.

• NEVER touch heated surfaces of the device during or shortly after use. ONLY use the handle and controls. Be careful to avoid direct contact with the heated plates while removing your finished products. Use of heat-resistant gloves to protect your hands and heat-resistant tape to secure your designs are both highly recommended.

• NEVER use if any parts are missing, loose, worn, damaged, or otherwise display signs of malfunction. Tighten, repair, or replace any problematic components before further use. Only allow trained technicians to work on internal components. Always fully replace damaged power cords and only replace components with identical parts.

• For best results, unplug this device when it is not in use or otherwise fully disconnect it from power. Only clean, repair, or perform other maintenance while this device is fully disconnected from power and fully cooled. Only use and store it in a location protected against unauthorized use and inaccessible to any children or pets.

SPECIFICATIONS

PRODUCT DIAGRAM

CONTROL PANEL

Setting Temperatures
Press SET once. The top display should read “SP”. Use ⯅ and ⯆ to adjust the target temperature.
Setting Timers
Press SET twice. The top display should read “S” and the lower display should show the default timer settings. Use ⯅ and ⯆ to adjust the heating timer.
Changing Temperature Units
Press SET 3 times until the top display changes to “C-F”. Use ⯅ and ⯆ to toggle between using Celsius and Fahrenheit units.
Starting Countdown
Press ⯆ once to start the countdown.

ASSEMBLY

Unpack your new heat press and its attachments. Find a place for use with a firm level surface able to easily bear the heat press’s weight. It should provide ample room to move around the heat press without any need to touch its heated surfaces. There should also be enough space nearby to easily use and store the press’s other attachments.
Your heat press uses its flat platen by default. Simply confirm that the electrical relay between the control box and platen is well connected and then connect the device to a stable, compatible, and grounded power supply.
You can also use other attachments (sold separately) by disconnecting the electrical relay and using it to power the compatible attachment.

OPERATION

1. Prepare your design on suitable transfer(s).
   When you first start using this device and before any big batch job, prepare a test transfer on a scrap of similar fabric to make sure that all of your settings are correct. The best settings will usually vary somewhat between different transfers, materials, and thicknesses.
   Research your specific material and its ideal settings before use. Most fabrics can be pressed, but not all. Most ceramics can be pressed, but some sublimation plates and mugs are especially formatted for easy design transfer. Use very low pressure for glass or plates, only the bare minimum to apply full and even contact with the transfer. Use the locking knob to lock the machine at your desired pressure.
   Remember that most transfers (but not all!) require the design to be applied in reverse.
   Make the necessary adjustments for the style of transfer that you’re using.

2. Swing the top of the press out of the way and prepare its heat-resistant mat.

3. Fit your product onto the middle of the base. Smooth out any wrinkles in the area that will be pressed. If you use a protective cover sheet, smooth out any of its wrinkles as well.

4. Flip the power switch on. Press SET and set the temperature value. Press SET and set the timer value. Press SET and choose whether your temperature is in Fahrenheit or Celsius degrees. Press SET a fourth time to begin heating.

5. Wait for the platen to heat.

6. Being careful to avoid touching any heated surfaces with any exposed skin, swing the platen over your design and press it down using the handle. Press ⯆ to start the timer.

7. The control box should announce when your countdown has ended. Carefully release the press, turn it off, and swing the heated platen away. Unless you are using heat-resistant gloves, allow time for objects to cool before removing them and moving on to your next product.

ADDITIONAL TIPS

• Remove transfer paper from finished items quickly to prevent it cooling and sticking to your design, but continue to be careful of the press’s heated surfaces. Allow vinyl a little more time to set but still remove it before it cools. Firm fabrics also allow an  easier earlier peel. Extremely stretchy fabrics might need your design to entirely cool before the transfer paper can be safely removed.
• Always use the exact settings for your transfer or material if one is provided. Experiment with your specific transfers and materials to find the best results, especially before large batches.
• As you become more comfortable with heat pressing, also experiment with trading higher heat for lower time or vice versa to create
• If you have the time or an especially important project, a short 5 second prepress of fabric items can help flatten, dry, preshrink, and prepare them before adding your transfer. Double or even triple the length of the prepress in especially humid environments.
• When adding designs to clothing or objects which include uneven elements like buttons or zippers, a heat-resistant pillow can be used to help ensure a full and even press. However, if such parts are themselves heat sensitive, be sure to position them away from the platen or cover them with a layer of heat-resistant material.
• Avoid washing newly printed items for at least 24 hours.

TYPICAL SETTINGS FOR COMMON MATERIALS

MAINTENANCE

• Always completely disconnect this device from power and wait for it to cool before any cleaning, repair, or other maintenance.
• Clean with a soft dry cloth. If a damp cloth is necessary, be sure not to get any electronic components wet. Do not use caustic chemicals or harsh abrasives.
• Check this device periodically for any looseness, wear, or damage. Tighten, repair, or replace any problematic parts before further use. Only allow trained technicians to do any testing or repairs to internal components.
• Store in a cool dry location inaccessible to children and away from direct sunlight. For best results, disconnect from power after each use. Always disconnect completely from power if it will not be used for an extended period of time.

TROUBLESHOOTING

Reduce the pressure with the adjustment knob.
Faded or pale images| Increase the time and/or temperature used.
Increase the pressure with the adjustment knob.
Lack of heat despite
correct control displays| Check the electrical relay between the control box and the heating platen.
Repair or replace the accessory’s heat unit.
Lack of heat and no
display when turned on| Check the main power cord.
Replace the device’s fuse if it has blown.
Excessive heating| Repair or replace the electrical relay between the control box and the
heating platen.

DISPOSAL

**** Electrical products should not be disposed of with household products. In the EU and UK, according to European directive 2012/19/EU for the disposal of electrical and electronic equipment and its implementation in national laws, used electrical products must be collected separately and disposed of at the collection points provided for this purpose. Locations in Australia, Canada, and the United States may have similar regulations. Contact your local authorities or dealer for disposal and recycling advice.

CONTACT US
Thank you for choosing our products! If you have any questions or comments, contact us at help@cs-supportpro.com and we’ll resolve your issue ASAP!
For a .pdf copy of the latest version of these instructions, use the appropriate app on your smartphone to scan the QR code to the right.

https://sp9c.com/FyDNf

HPM-230D-US HPM-230D-UK HPM-230E-US HPM-230E-UK HPM-230P-UK HPM-230P-UU HPM- 230Q-UK HPM-230Q-UU
Rev. 14 Dec. 2022

References

• Transparent outsourced web hosting tech support |SupportPRO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>