CREWORKS V20230628 Manual Wire Stripping Machine User Manual

V20230628 Manual Wire Stripping Machine
User Manual

V20230628 Manual Wire Stripping Machine

Read Carefully Before Use
Keep for Future Reference

Safety Information

Warning!

• Read these instructions carefully before use. Follow ALL instructions and contact customer service if any point is confusing or unclear. Keep these instructions for future reference. Provide them to anyone who will use this device and provide them with this device if it is ever given or sold to a third party.
• DO NOT allow use by children, by anyone who has not read these instructions, or by any person whose mental or physical condition precludes safe use. Keep children, bystanders, and pets away while using this device. Restrict access to the work area if necessary.
• DO NOT use this device if you are tired or under the influence of drugs, alcohol, or medication.
• NEVER operate this device in the presence of any flammable, explosive, or corrosive liquids, gases, or dust.
• ONLY use in well ventilated locations to allow debris and fumes to dissipate quickly.
• ALWAYS keep your work area clean and well lit. Cluttered or dark areas invite accidents.
• ONLY place this device on even, stable, heat-resistant, and nonslip surfaces. Firmly attach this device to the surface using the provided bolts.
• ALWAYS wear appropriate personal protective equipment (PPE) including hand protection during use. Depending on your application or work area, eye and breathing protection may be necessary. The breathing protection must be able to filter all particles generated by your work, even when working outdoors. Anyone allowed nearby during use should wear equivalent PPE.
• DO NOT wear loose clothing or jewelry and tie back long hair during operation. Keep your clothing, hair, and gloves away from any moving parts.
• DO NOT overreach. Keep proper footing and balance at all times.
• ALWAYS remove any adjustment tools before starting use.
• NEVER place your fingers or any other body parts near the cutting area during use.
• DO NOT force this device. Only use on wires within the size range specified in this manual and only with the guards and blades set to the appropriate height. Clean and lubricate as needed if parts begin to move slowly.
• NEVER leave this device unattended or adjust this device’s settings during use.
• DO NOT touch the blade, rollers, or other parts in the cutting area with bare skin immediately after use, as they may remain hot.
• Clean and maintain this device. Check for misalignment, breakage of components, or any other condition that may affect the device’s operation. If damage or malfunction is detected, have the problematic part repaired or replaced before further use. NEVER replace any components with nonidentical ones.

Specifications

• Wire diameters INCLUDE insulation. (AWG conversion will vary with insulation thickness.)

Package List

Not Included but Helpful

• Impact Wrench
• Power Drill
• Tap Wrench
• 9 mm Hex Socket
• 40 mm Wood Board
• Mineral Oil

Product Diagram

Installation

ALWAYS use the appropriate PPE for your work such as the work gloves (F) and NEVER place any body part near the cutting area during use.

1. Connect the handle (B) to the right side of the wire stripper (A). Secure it in place using the M6×14 bolt (C) and the provided hex wrench (E). Alternatively, you can replace the handle with an impact wrench and 9 mm hex socket (not included).
2.  Attach the device to any level and sturdy surface at least 1⅝ inches (40 mm) thick using the M6×45 bolts (D).

Operation

1. Raise the blade by turning its adjustment knob counterclockwise to allow sufficient room between the blade and rollers for your wire.

2. Release the upper safety guard by loosening its locking knob on the left side of the device. Slide the guard up, feed your wire through the hole this creates, and slide the guard back down to your desired size. Check that the edge of the hole does not interfere with your wire feeding and then retighten the knob to lock the guard in place.

3. Insert your wire and then lower the blade by turning its adjustment knob clockwise until you feel the blade touch your wire.

4. Begin stripping the wire by turning the handle or using your impact wrench to do so.
   If your wire’s insulation is not removed, stop use, raise the blade, remove your wire, and then further lower the blade before beginning again.
   NEVER adjust any setting while the blade is still moving.
   To pause work, follow the same process. Stop use, raise the blade, and remove your wire.
   DO NOT leave partially stripped wire lying in the device unattended.

5. After all your work is completely finished, remove any debris from the device.

Maintenance

• Clear any remaining debris, dust, or other dirt off the blade, rollers, feed holes, base, and any other external surfaces with a soft damp cloth, a soft dry brush, or OSHA/HSE-compliant levels of compressed air. Do not use harsh abrasives or caustic chemicals.
• Lubricate the moving parts with mineral oil (not included) as needed, particularly the blade and rollers.
• Sharpen or replace the blade when it no longer provides quick or smooth cuts. Have a qualified technician do so if needed.
• Check the parts for any looseness, wear, or damage between uses. Tighten, repair, or replace any problematic components before further use.
• If this device will not be used for an extended period of time, unbolt it and store it and its accessories in a cool dry place away from direct sunlight and inaccessible to children.

Troubleshooting

knob counterclockwise.
Adjust the feed hole appropriately for the wire’s total diameter including insulation.
The plastic covering has been cut open but the copper wire cannot be removed.| Lower the blade by turning its adjustment knob clockwise.
Adjust the feed hole appropriately for the wire’s total diameter including insulation.
The wire jams inside the device.| Stop the rollers and raise the blade as above. Pull the wire out, lower the blade back into place, and reinsert the wire.
Clean the wire if it has dirt, grime, etc. that are obstructing this device. Clear off any debris remaining inside the device before further use.

Contact Us

https://sp9c.com/wKfjt
Thank you for choosing our products! If you have any questions or comments,
contact us at contact@b2ccsgroup.com and we’ll resolve your issue ASAP!
For a .pdf copy of the latest version of these instructions, use the appropriate
app on your smartphone to scan the QR code to the right.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>