KAER Lateral File Cabinets with Lock Instruction Manual

KAER Lateral File Cabinets with Lock

INSTALLATION INSTRUCTION
Please do not put the USB Key and Set Needle in the cabinet!

NOTE:

• Please read the complete assembly instructions carefully before assembling the cabinet
• Check the materials to make sure they are working correctly and are not damaged.
• Cabine1s should be assembled on a flat surface.
• Refer to the illustrations to identify the parts and accessories of the cabinet.

Tools

INSTALLATION INSTRUCTION **

**

1. Insert two drawer sides into edge fold of drawer front

2. Bend the tableting of drawer front and fasten them to drawer sides.

3. Insert the drawer bottom into edgefold of drawer front and drawer sides respectively.

4. Bend the tabletting of ead1 drawer side and fasten them to drawer bottom.

5. Insert drawer back into edgefold of drawer  bottom and drawer sides respectively.

6. Bend tableting of drawer sides and drawer bottom , fasten them to drawer back.

7. Fasten drawer front hanger to the back of drawer front with four self-tapping screws.

8. Insert two cabinet sides into laterals of cabinet bottom.

9. Fasten cabinet back to cabinet sides and cabinet bottom with five self-tapping screws.

10. Insert the two cabinet sides into grooves of cabinet top.

11. Fasten the cabinet back to the cabinet top with one self-tapping screw.

12. Fasten two reinforced studdles to the edgefold of cabinet sides.

13. Bend the tablettings of cabinet top plate, bottom plate and sides plate, fasten them to the reinforced studdles.
    

14. For two cabinets connected, using screwdriver to drill a hole of each side and fasten them with coupling screws, gaskets and coupling nuts. Fix the cabinet to the wall with gaskets, connecting pieces and expansion bolts.

15. Insert back of the track into socket of the cabinet plate, push down the front and get stuck in hanging hole of the cabinet sides.

16. Bend the tapping sttudles of cabinet sides out and get stuck in the tracks.

17. Put the drawer in and insert the hook on the back of tracks into hanging hole in ead7 back of drawer side.

18. Insert the hook on the front of tracks into hanging hole in each front of drawer side.

19. Put on drawer vertical hanger on the drawer.

SMART DIGITAL LOCK USER MANUAL

Please Do Not Put USB Key and Set Needle in the Cabinet !

BATTERY INSTALLATION
Slide the battery cover (shown above) and input three AAA alkaline batteries.

Note:

• Please do not use rechargeable batteries.
• Please do not use different brands of batteries, the current is different cannot energize the panel and may burn the panel.
• If the panel is not energized after installing the batteries, please check if the batteries are low.

ORIGINAL FACTORY SETTING

1. The factory setting user code is 1234.
2. The factory setting management code is 543215.

Note:

• The system support 1 owner key and 3 management keys.
• There are three modes: automatic, manual and public mode.

CHANGE USER CODE (For automatic and manual mode)

1. Press “*” for 2 seconds, red light turns on.
2. Enter original user code or management code, press “#” to confirm.
3. Enter “1” and press ‘#’ to confirm.
4. Enter new user code (1 to 10 digits) and press “#” to confirm.
5. Enter new user code again, then press “#” to confirm.
6. Red light turns off and ‘beep’ sounds twice, as indicates the user code has been changed successfully.

CHANGE MANAGEMENT CODE

1. Press “*” for 2 seconds, red light turns on.
2. Enter original management code, press “#” to confirm.
3. Enter “2” and press ‘#’ to confirm.
4. Enter new management code (1 to 10 digits) and press “#” to confirm.
5. Enter new management code again, then press “#” to confirm.
6. Red light turns off and ‘beep’ sounds twice, as indicates the management code has been changed successfully.

UNLOCK AND LOCK

1. Unlock:
   Enter correct user code or management code then press “#” to conform. when you heard ‘beep’ twice and green light turns on, it indicates unlock . You can press “*” to delete the wrong input code.

2. Lock:
   Three ways to lock the cabinet.

3. In automatic mode, the latch will protrude automatically within 4 seconds.

4. In manual mode, press “#” to lock the door.

5. In public mode, input user code and press “#” to lock the door.

CHANGE LOCK MODE
There are 3 modes: automatic mode, manual mode and public mode.

1. Press “*” for 2 seconds, red light turns on.
2. Enter management code, then press “#” to confirm.
3. Enter “3” and press ‘#’ to confirm.
4. Enter “1#” to set automatic mode, enter “2#” to set manual mode or enter “3#” to set public mode.
5. Red light turns off, ‘beep’ sounds twice, as indicates the mode has been set successfully .

RECOVER TO FACTORY SETTING CODE
Press the setting button (which is beside the hole of latch) for 4 seconds, ‘beep’ sounds twice, the user code is recovered to 1234, and the management code is recovered to 543215.( Except public mode）

CHANGE THE BATTERIES
After using for some time, in unlock status, ‘beep’ sounds 6 times and red light flashing 6 times, as indicates low battery. Please change the batteries as soon as possible.

USB KEY MANAGEMENT SYSTEM

The system support 1 owner key and 3 management keys. Owner key is used for setting and opening, and management key is only used for opening.

1. To set owner key:
   In automatic mode or manual mode, insert the owner key into USB port, press the button, then hold on the setting button for 4 seconds, ‘beep’ sound 4 times after 4 seconds. The system is recovered to factory setting status. At this time, the key has been set successfully as owner key.
   Insert the owner key into USB port, it will be unlock automatically.

2. With the owner key in the USB port, you can set below functions:

3. Recover the code to factory setting status:
   Enter “11#”, ‘beep’ sounds twice, user code and management code are recovered to factory setting status.

4. Register management key:
   Enter “22#”, take out the owner key, the buzzer sounds all the time, insert a new USB key, ‘beep’ sounds twice, as indicates the key has been set successfully , ‘beep’ sounds 3 times indicate failure. Take out above USB key, the buzzer sounds all the time, you can insert a new e-key to set another management key, totally 3 management USB keys can be set. In case no more new USB key is inserted, the system will be logout within 8 seconds.

5. Delete management USB key:
   Enter “33#”, ‘beep’ sounds 3 times, all management keys are deleted.

6. Set the mode:

7. Enter “44#1#” to set automatic mode.

8. Enter “44#2#” to set manual mode.

9. Enter “44#3#” to set public mode.
   Two beeps will sound after above operation, as indicates the mode has been set successfully.

PUBLIC MODE
Public mode is used for temporary storage in public places.

1. Enter a 1 to 10 digits user code when locking the door, and then enter “#” to confirm.
2. Enter the password you have set and press’#’ to unlock the door.
3. Be careful, do not let the door lock automatically when leaving.
4. If the customer forgets the password or locks the cabinet without setting password, the manager can use the USB key or the management code to open the cabinet.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>