ManualsPro Epson Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays Installation Guide

Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays Installation Guide

June 17, 2024
Epson

Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser DisplaysInstallation Guide

About This Installation Guide

This guide describes how to mount the ultra-short-throw projectors listed below to a wall using the Epson® ELPMB62 wall mount.
The following projectors are covered by this guide:

  • BrightLink® 1480Fi/1480Fi+
  • BrightLink® 1485Fi/1485Fi+
  • BrightLink® EB-725Wi/EB-735Fi
  • BrightLink® EB-760Wi/EB-770Fi
  • PowerLite® EB-720/EB-725W
  • PowerLite® EB-750F/EB-755F
  • PowerLite® EB-760W
  • PowerLite® EB-770F/EB-775F
  • PowerLite® EB-800F/EB-805F

The BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ is shown in most illustrations in this guide, but the steps are the same for all models unless otherwise noted.

Safety Instructions

For your safety, read all the instructions in this guide before using the wall mount. Incorrect handling that ignores instructions in this guide could damage the wall mount or could result in personal injury or property damage. Keep this installation guide on hand for future reference.
Read the safety instructions in the online User’s Guide for your projector and follow the instructions in this document.

Explanation of Symbols

The warning marks shown below are used throughout this installation guide to prevent personal injury or property damage. Make sure you understand these warnings when reading this installation guide.

Warning| This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
---|---
Caution| This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
| This symbol indicates related or useful information.
| Symbol indicating an action that must not be done
---|---

| Symbol indicating an action that should be done

Safety Precautions for Installation

Warning
The wall mount is designed specifically for mounting a projector to a wall. If anything other than a projector is mounted, the weight may result in damage.
If the wall mount falls, it could cause personal injury or property damage.
The installation work (wall mounting) should be performed by specialists who have technical knowledge and ability. Incomplete or incorrect installation could cause the wall mount to fall and cause personal injury or property damage.
Follow the steps in this guide to install the wall mount, and be sure to use the bolts and screws specified in this guide
If the instructions are not followed, this product may fall, resulting in personal injury or an accident.
Handle the power cord carefully.
Incorrect handling may cause fire or electric shock. Observe the following precautions when handling:

  • Do not handle the power plug with wet hands.
  • Do not use a power cord that is damaged or modified.
  • Do not pull the power cord with too much force when routing the cable through the wall mount.

Do not install the wall mount in a place where it might be subjected to vibration or shock.
Vibration or shock could cause damage to the projector or mounting surface. It could also cause the wall mount or projector to fall and cause personal injury or property damage.
The installation work should be performed by at least two qualified service personnel. If you need to loosen any screws during installation, be careful not to drop the wall mount.
If the wall mount or projector falls, it could cause personal injury or property damage.
Make sure you use the included safety wire kit when mounting your projector.
Install the wall mount so that it can sufficiently support the weight of the projector and wall mount, and resist any horizontal vibration. Use M10 or 3/8 inch nuts and bolts and make sure to use appropriate wall anchors for your wall type.
Nuts and bolts smaller than M10 or 3/8 inch could cause the wall mount to fall. Epson accepts no responsibility for any damage or injury caused by lack of wall strength or inadequate installation.
When you mount the projector on the wall with the wall mount, the wall must be strong enough to hold the projector and the wall mount.
The maximum combined weight of the projector and wall mount is approximately 41.7 lb (18.9 kg). If the wall is not strong enough, reinforce the wall before installation.
The installation work should be performed by at least two qualified service personnel. If you need to loosen any screws during installation, be careful not to drop this product.
If this product falls, it could cause damage or injury.
Inspect the wall mount on a regular basis to ensure there are no broken parts or loose screws.
If there are any broken parts, stop using the wall mount immediately. If the wall mount or projector falls, it could cause personal injury or property damage.
Never modify the wall mount.
Do not hang on the wall mount or hang a heavy object on the wall mount.
If the projector or wall mount falls, it could cause personal injury or property damage.
Do not use adhesives, lubricants, or oils to install or adjust the wall mount.
If you use adhesives to prevent the screws from loosening or things such as lubricants or oils on the part of the projector attached to the slide plate, the case may crack and cause the projector to fall, resulting in personal injury or property damage.
Tighten all screws firmly after adjustment.
Otherwise, the projector or wall mount may fall and cause personal injury or property damage.
Never loosen the bolts and nuts after installation.
Confirm that the screws have not become loose on a regular basis. If you find any loose screws, tighten them firmly. Otherwise, the projector or wall mount may fall and cause personal injury or property damage.
When performing wiring, make sure the cable does not come into contact with any screws or bolts.
Handling the cable incorrectly may cause fire or electric shock.
Do not install in a location subject to oily smoke or smoke for events.
If oils stick to the slide plate fixing part of the projector, the case may crack and cause the projector to fall, resulting in personal injury or property damage.
Follow the instructions in this guide to install and operate the touch unit.
If the touch unit is not installed and operated properly, the light emitted from the laser could cause injury to eyesight.
Never modify the control pad or touch unit.
When performing wiring, make sure the cable does not come into contact with any screws or bolts.
Handling the cable incorrectly may cause fire or electric shock.
Do not apply optical devices such as a magnifying glass or telescope to the laser light diffused from the touch unit.
If such optical devices are applied, it could cause personal injury or fire.
Do not look into the touch unit’s laser diffusion ports.
This could cause injury to eyesight. Extra care should be taken when children are present.
Do not view the laser light using optical devices such as a magnifying glass within a range of 2.75 inches (70 mm).
Viewing at close range could cause injury to eyesight.
Connect the touch unit to BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+/EB-725Wi /EB-735Fi/EB-760Wi/ EB-770Fi models only. Do not connect it to any other projectors or devices.
Do not use the touch unit if you are using or are near medical equipment such as a pacemaker.
The magnet within the touch unit generates electromagnetic interference which could cause medical equipment to malfunction.

Caution
Do not install the wall mount in a location where the operating temperature for your projector model may be exceeded. Such an environment may damage the projector.
Install the wall mount in a place free from excessive dust and humidity to prevent the lens or optical components from becoming dirty.
Do not use excessive force when adjusting the wall mount.
The wall mount may break, resulting in personal injury.
Keep magnetic storage media (for example, magnetic cards or electronic devices such as computers, digital watches, or cell phones) away from the touch unit.
The magnet within the touch unit generates electromagnetic interference which could corrupt data or cause the media or device to malfunction.

Installation Location

  • Before installing the projector, verify the power supply wiring for the installation location.
  • If you want to hide the projector power plug under the wall plate cover, make sure the power outlet is located in the empty space to the left or right of the wall plate.
  • Install the projector away from other electric devices such as fluorescent lights or air conditioners. Some kinds of fluorescent lights could interfere with the remote control of the projector.
  • Install the projector away from direct sunlight and other bright light sources.
  • Make sure there is at least 20 inches (50 cm) of space between the wall and the projector’s air exhaust and intake vents on the left and right.
  • It is recommended to keep VGA computer cable length less than 65 feet (20 meters) to reduce external noise.
  • Install the projector at an angle of no more than 3° horizontally or vertically in relation to the projection surface.
  •  Install the projector in a location where the projected image is within reach.
  • When installing two or more projectors, check the following:
  • Make sure the temperature of the surrounding environment is less than 95°F (35°C). If the environment is too hot, the projectors may overheat and the power may turn off without warning.
  • Make sure you leave a gap of at least 47.2 inches (120 cm) between the projectors.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

If the projectors are installed closer than 47.2 inches (120 cm) apart, install a partition to block the heat from the projector’s exhaust vent. The partitions should be larger than the exhaust vent and installed approximately 15.7 inches (400 mm) from the exhaust vent and 7.9 inches (200 mm) from the intake vents.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

For detailed information on setting up two or more projectors, see the online Edge Blending Setup Guide for your product.

  • Before installing the touch unit (included with the BrightLink 1485Fi/1485Fi+; available as an optional accessory for the BrightLink 1480Fi/1480Fi+/EB-725Wi/EB-735Fi/EB-760Wi/EB-770Fi), verify that the installation location meets the following conditions:

  • The touch unit can be secured to the surface with magnets or screws, or the optional touch unit bracket.

  • The surface is flat, smooth, and unwarped with no more than 0.2 inch (5 mm) of unevenness in any direction on the screen surface.

  • When installing the touch unit (included with the BrightLink 1485Fi/1485Fi+; available as an optional accessory for the BrightLink 1480Fi/1480Fi+/EB-725Wi/EB-735Fi/EB-760Wi/EB-770Fi) within the frame of the whiteboard, secure the touch unit with magnets or screws. Make sure there are no obstacles, such as cables, or protruding objects such as whiteboard trays, pen holders, or thick frames in the shaded areas in the following figure. The touch unit will not operate correctly if anything is obstructing the infrared signal. If there is an obstacle that cannot be removed, you can use the supplied infrared deflectors to prevent laser detection issues.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

  • fig 4](https://manuals.plus/wp-content/uploads/2024/02/Epson-V12HA06A05 -Adjustable-Wall-Mount-For-Ultra-Short-Throw-Laser-Displays-fig-4.png)

    • When installing the touch unit (included with the BrightLink 1485Fi/1485Fi+; available as an optional accessory for the BrightLink 1480Fi/1480Fi+/EB-725Wi/EB-735Fi/EB-760Wi/EB-770Fi) above the frame of a whiteboard, use the optional touch unit bracket.
    • If the distance from the wall to the surface of the whiteboard is greater than 2 inches (51 mm), you must install the touch unit on the whiteboard.
    • If the frame of the whiteboard extends more than 0.1 inch (3 mm) away from the board surface, you must install the touch unit on the whiteboard or screen.

Package Contents

Wall Mount

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

# Part name
1 End cap
2 3-axis adjustment unit and slide plate (attached when shipped)
3 Wall mount
4 Wall plate
5 Wall plate cover
6 Hexagonal shaft

Hardware

Shape Name Quantity Application
**** M4 × 12 mm hexagon socket head cap bolt with washer/spring washer 5

For wall plate assembly
4| For 3-axis adjustment unit/wall mount installation
4| For slide plate/projector installation
| M6 × 20 mm hexagon shoulder head bolt with washer/spring washer| 1| For wall mount/wall plate installation
| M6 × 20 mm cross recessed head shoulder screw with plastic washer| 3
****| M3 × 6 mm cross recessed head shoulder screws| 4| For Mini PC plate installation

  • Use the bolts or screws supplied with the wall mount to install it as directed in this guide. Do not substitute these bolts with any other types.
  • You need to use commercially available M10 × 60 mm or 3/8 inch anchors (at least 4) and one M10 screw to attach the wall plate to the wall.
  • Gather the tools and parts you need before you begin installation, including a #3 cross-head screwdriver.

Accessories

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Touch unit (included with BrightLink 1485Fi/1485Fi+)
The following parts are packaged with the BrightLink 1485Fi/1485Fi+ (available as an optional accessory for the BrightLink 1480Fi/1480Fi+/EB-725Wi/EB-735Fi /EB-760Wi/EB-770Fi) and are necessary when attaching thetouch unit. When installing the touch unit on a non-magnetic screen or whiteboard, you will also need three M4 screws.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Optional touch unit bracket
The following parts are packaged with the optional touch unit bracket (available as an optional accessory for BrightLink models listed in this guide) and are necessary when attaching the touch unit above the frame of a whiteboard. When installing the bracket, you will also need four (4) M4 wood screws or M4 anchor bolts (not included).

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Control pad (included with BrightLink 1485Fi/1485Fi+)
The following parts are packaged with your projector (BrightLink 1485Fi/1485Fi+ only; available as an optional accessory for the PowerLite EB- 800F/EB-805F) and are necessary when attaching the control pad.
When installing the control pad on a wall, you will also need four commercially available M4 × 20 mm screws.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Specifications

Item| Specification| Additional information| Reference page
---|---|---|---
Wall mount weight (including the 3-axis adjustment unit, slide plate, wall plate, wall plate cover, and end cap)| Approx. 20.3 lb (9.2 kg)| —| —
Maximum load capacity| 33.1 lb (15.0 kg)| —| —
Vertical slide adjustment range| ±1.6 in. (40 mm)| —| Refer to the illustration on page 14
Horizontal slide adjustment range| ±1.8 in. (45 mm)| —| Refer to the illustration on page 14
Forward/backward slide adjustment range| 0 to 15.1 in. (0 to 383 mm)| Determine adjustment unit installation position based on screen size| Refer to the illustration on page 15
Horizontal roll adjustment range| ±3°| Fine adjustments possible with adjustment dial| p. 69
Horizontal rotation adjustment range| ±8°| Fine adjustments possible with adjustment knob| p. 69
Vertical tilt adjustment range| ±3°| Fine adjustments possible with adjustment dial| p. 70

Wall plate cover

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Wall plate
The wall plate is in three pieces when shipped. Use the included M4 × 12 mm bolts (×5) to attach the separate pieces together before mounting the projector. See page 52 for instructions.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Vertical slide adjustment range

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Horizontal slide adjustment range

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Forward/backward slide adjustment range
Arm slide adjustment range

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Adjustment from 3-axis adjustment unit installation position
By changing the installation position of the 3-axis adjustment unit to the front or back, you can adjust the installation position of the projector.

  • BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F: Mount it at the stamp when the image is less than 80 inches diagonally, or at the stamp when the projected image is 80 inches or more diagonally.
  • BrightLink EB-725Wi/EB-735Fi/EB-760Wi/EB-770Fi and PowerLite EB-720/EB-725W/EB-750F/ EB-755F/EB-760W/EB-770F/EB-775F: Mount it at the stamp when the image is less than 90 inches diagonally, or at the stamp when the projected image is 90 inches or more diagonally.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

To see these stamps, you need to remove the two top bolts and slide out the arm extension.

Touch unit (included with BrightLink 1485Fi/1485Fi+)
External dimensions and weight
The touch unit weighs approximately 21.2 ounces (600 g).

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Attached labels
The touch unit is a Class 1 laser product that conforms to the IEC/EN60825-1:2014 standard. There are warning labels affixed to the touch unit to indicate that it is a Class 1 laser product. The labels contain the following information:

  • Class 1 laser product
  • Warning: Never open any covers on this unit. Laser product inside.
  • Warning:
  • Caution: Class 3B invisible laser radiation when open.
  • Avoid exposure to the beam.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Laser diffusion port
The laser beam is diffused from the laser diffusion ports on the bottom of the touch unit.

  • Light source output: Max. 285 W
  • Wavelength: 932 to 952 nm

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Control pad (included with BrightLink 1485Fi/1485Fi+)
External dimensions and weight
The control pad weighs approximately 22.2 ounces (630 g).

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Cable routing holes
When routing cables, use the positions (A) in the following figure as the cable routing holes. Route the power cable along the groove on the back of the control pad (B).

Pen stand (included with BrightLink 1485Fi/1485Fi+/EB-725Wi/EB-735Fi/ EB-760Wi/EB-770Fi)
External dimensions and weight
The pen stand weighs approximately 3.3 ounces (93 g).

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Connecting Devices

Make sure you have the power cord, computer cable, and other parts at the location where the wall mount is to be installed. Make sure you also have all necessary cables for the Touch Unit (if applicable) and other devices, such as a document camera or microphone, that you will connect to the projector. Your projector’s connection panel may differ slightly from the model in the illustrations. For details, refer to the online User’s Guide for your projector.
The connection example below shows the control pad (included with the BrightLink 1485 Fi/Fi+ only).
Connection Example

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

For Interactive Use
When interacting with a computer, you also need a USB cable that runs from the computer to the projector. However, when using the projector’s built-in toolbar, you do not need this USB cable.

Connecting the Control Pad
The Control Pad is included with the BrightLink 1485Fi/Fi+. It provides a convenient alternative for turning on and controlling your projector.
You must install the projector before installing the control pad. See page 106 for instructions.

Positioning the Projector

Your Epson projector can project images up to the following sizes:
This guide covers select image sizes. For other image sizes, use the Throw Distance Calculator at http://epson.com/support (U.S.), http://epson.ca/support (Canada), or http://latin.epson.com/support (Latin America).

Projector Maximum projected image size (diagonally)
16:10 16:9
BrightLink 1480Fi/1480Fi+ 90 inches
supported 120 inches
BrightLink 1485Fi/1485Fi+ 90 inches

120 inches
BrightLink EB-725Wi/EB-760Wi| 100 inches| 100 inches| 100 inches| Not supported| Not supported
BrightLink EB-735Fi| 100 inches| 100 inches| 98 inches| 110 inches| Not supported
BrightLink EB-770Fi| 100 inches| 100 inches| 100 inches| 110 inches| 110 inches
PowerLite EB-720| 103 inches| 101 inches| 110 inches| Not supported| Not supported
PowerLite EB-725W| 120 inches| 116 inches| 106 inches| Not supported| Not supported
PowerLite EB-750F/EB-755F| 110 inches| 120 inches| 98 inches| 110 inches| Not supported
PowerLite EB-760W| 138 inches| 134 inches| 122 inches| Not supported| Not supported
PowerLite EB-770F/EB-775F| 132 inches| 143 inches| 117 inches| 133 inches| 136 inches
PowerLite EB-800F/EB-805F| 90 inches| 130 inches| 80 inches| 120 inches| 120 inches

You can project onto a pre-installed whiteboard or directly onto a plain wall.
The height of the included wall mount determines the maximum image size and how high the image appears on the wall or whiteboard. The distance of the projector from the wall (once it is mounted on the adjustable arm of the wall mount) also affects image size and position.
If you want to install the Touch Unit outside of the frame of a whiteboard, use the optional Touch Unit Bracket.
If the distance from the wall to the surface of the whiteboard is greater than 2 inches (51 mm) or the frame of the whiteboard extends more than 0.1 inch (3 mm) away from the board surface, you must install the Touch Unit on the whiteboard or screen.
If you are planning to project on a whiteboard, the image may not fill the entire board, depending on the aspect ratio. If you match the image height to the board’s height, gaps may appear on the sides of the board.
Use the following worksheets to determine the proper location of the wall plate on the wall. If you are projecting onto a pre-installed whiteboard, use the worksheet on page 23. If you are projecting on a plain wall, use the worksheet on page 25.

When installing the Touch Unit on a whiteboard (if applicable), make sure there are no cables, whiteboard trays, pen holders, or thick frames in the following areas around the edge of the board:
❏ From the top of the projected image to the bottom of the Touch Unit:

  • BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+: 0.79 to 2 inches (20 to 50 mm) for 16:6 (BrightLink 1485Fi/1485Fi+ only) and 21:9 aspect ratios; 0.22 to 2 inches (5.7 to 50 mm) for all other aspect ratios
  • BrightLink EB-770Fi: 1.83 to 2 inches (46.4 to 50 mm) for 16:6 aspect ratio; 1.5 to 2 inches (38.1 to 50 mm) for 21:9 aspect ratio; 0.76 to 2 inches (19.2 to 50 mm) for all other aspect ratios
  • BrightLink EB-735Fi: 1.61 to 2 inches (41 to 50 mm) for 16:6 aspect ratio; 0.70 to 2 inches (17.7 to 50 mm) for all other aspect ratios
  • BrightLink EB-760Wi: 0.65 to 2 inches (16.4 to 50 mm) for all aspect ratios
  • BrightLink EB-725Wi: 0.54 to 2 inches (13.7 to 50 mm) for all aspect ratios

❏ From the edges of the projected image to the edges of the board: at least 4 inches (100 mm) left and right
❏ From the bottom of the projected image to the bottom of the board: 0.8 inch (20 mm)

If there are obstacles such as within the areas listed above, the Touch Unit will not operate properly.

Installation worksheet for projecting on a pre-installed wall-mounted board

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Distance from top of image area to bottom of Touch Unit (if applicable):

Model| 21:9 aspect ratio| 16:6 aspect ratio| All other aspect ratios
---|---|---|---
BrightLink 1480Fi/1480Fi+/ 1485Fi/1485Fi+| 0.79 to 2 inches (20 to 50 mm)| 0.79 to 2 inches (20 to 50 mm) (BrightLink 1485Fi/1485Fi+ only)| 0.22 to 2 inches (5.7 to 50 mm)
BrightLink EB-770Fi| 1.5 to 2 inches (38.1 to 50 mm)| 1.83 to 2 inches (46.4 to 50 mm)| 0.76 to 2 inches (19.2 to 50 mm)
BrightLink EB-735Fi| —| 1.61 to 2 inches (41 to 50 mm)| 0.70 to 2 inches (17.7 to 50 mm)
BrightLink EB-760Wi| —| —| 0.65 to 2 inches (16.4 to 50 mm)
BrightLink EB-725Wi| —| —| 0.54 to 2 inches (13.7 to 50 mm)

If you want to install the Touch Unit (BrightLink models only) outside of the frame of a whiteboard, use the optional Touch Unit Bracket. If the distance from the wall to the surface of the whiteboard is greater than 2 inches (51 mm) or the frame of the whiteboard extends more than 0.1 inch (3 mm) away from the board surface, you must install the Touch Unit on the whiteboard or screen.
See page 76 for details on mounting the Touch Unit.

  1. Measure the ceiling height (distance from the floor to the ceiling). _____

  2. Measure the height of the board’s image area (h). _____ (h)

  3. Measure the width of the board’s image area (w). _____ (w)

  4. Measure the distance from the floor to the bottom of the board’s image area (f). _____ (f )

  5. Measure the thickness of the board (distance from the projection surface to the wall) (x). _____ (x)

  6. Determine the aspect ratio of the board or of the images that will be projected. You may need to consult your IT department for this information.
    4:3 XGA 16:10 WXGA/WUXGA 16:9 Widescreen 16:6* ___ 21:9*
    BrightLink 1485Fi/1485Fi+/EB-735Fi/EB-770Fi and PowerLite EB-750F/EB-755F/EB-770F/EB-775F/EB-800F/EB-805F only.
    **BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+/EB-770Fi and PowerLite EB-770F/EB- 775F/EB-800F/EB-805F only.
    If your desired aspect ratio does not match the native aspect ratio of your product, use the Throw Distance Calculator at http://epson.com/support (U.S.), http://epson.ca/support (Canada), or http://latin.epson.com/support (Latin America) to determine the correct measurements.

  7. Using the tables on pages 29 to 51 and your desired image height (h), find the required distance between the top of the image area and the bottom holes of the wall plate (c). _____ (c)

  8. Using the tables on pages 29 to 51 and your desired image height (h), find the required distance between the top of the image area and the temporary wall plate hole (d). _____ (d)

  9. Determine the position for your projector installation by adding the values for (f ), (h), (f) and (c), plus an additional 11 inches (280 mm) for the height of the wall plate plus the cover. (h)
    If the ceiling height of your room (as noted in step 1) does not meet the minimum (c) ceiling height required for your board, you may need to select a smaller image size or + 11 inches (280 mm) move the board to a lower position on the wall. total

  10. After confirming your image size, use tape or a pencil to mark the distance (c) from the top of the image area on the board to the bottom holes of the wall plate.

  11. Align the line (horizontal) on the template sheet with the (c) mark, then align the center line on the template sheet with the center of the image area. Follow the instructions on page 52 to install the projector.

Installation worksheet for projecting on a plain wall

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Distance from top of image area to bottom of Touch Unit (if applicable):

Model| 21:9 aspect ratio| 16:6 aspect ratio| All other aspect ratios
---|---|---|---
BrightLink 1480Fi/1480Fi+/ 1485Fi/1485Fi+| 0.79 to 2 inches (20 to 50 mm)| 0.79 to 2 inches (20 to 50 mm) (BrightLink 1485Fi/1485Fi+ only)| 0.22 to 2 inches (5.7 to 50 mm)
BrightLink EB-770Fi| 1.5 to 2 inches (38.1 to 50 mm)| 1.83 to 2 inches (46.4 to 50 mm)| 0.76 to 2 inches (19.2 to 50 mm)
BrightLink EB-735Fi| —| 1.61 to 2 inches (41 to 50 mm)| 0.70 to 2 inches (17.7 to 50 mm)
BrightLink EB-760Wi| —| —| 0.65 to 2 inches (16.4 to 50 mm)
BrightLink EB-725Wi| —| —| 0.54 to 2 inches (13.7 to 50 mm)

  1. Measure the ceiling height (distance from the floor to the ceiling). _____

  2. Determine the aspect ratio of the board or of the images that will be projected. You may need to consult your IT department for this information.
    4:3 XGA 16:10 WXGA/WUXGA 16:9 Widescreen 16:6* ___ 21:9*
    BrightLink 1485Fi/1485Fi+/EB-735Fi/EB-770Fi and PowerLite EB-750F/EB-755F/EB-770F/ EB-775F/EB-800F/EB-805F only.
    **BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+/EB-770Fi and PowerLite EB-770F/EB- 775F/ EB-800F/EB-805F only.
    If your desired aspect ratio does not match the native resolution of your product, use the Throw Distance Calculator at http://epson.com/support (U.S.), http://epson.ca/support (Canada), or http://latin.epson.com/support (Latin America) to determine the correct measurements.

  3. Using the tables on pages 29 to 51, select the largest image size available for your ceiling height.
    Image height (h) (h)
    Image width (w)     (w)

  4. Determine the desired distance from the floor to the bottom of the image area (f )._____ (f)
    The recommended minimum distance is 30 inches (762 mm). Images appearing less than 28 inches (711 mm) from the floor may be obstructed for some viewers.

  5. Find the top of the projected image area by adding distances (f ) and (h). _____

  6. Use the tables on pages 29 to 51 to determine the required distance from the top of the image area to the bottom holes of the wall plate (c). _____ (c)

  7. Use the tables on pages 29 to 51 to determine the required distance between the top of the image area and the temporary wall plate hole (d). _____ (d)

  8. Add:
    Required distance from top of image area to bottom holes of wall plate (c) (c)
    Height of image area (h)     (h)
    Distance from floor to bottom of image area (f) (f)
    Height of wall plate plus cover
    If the total exceeds the ceiling height, you will need to reduce the image size or reduce the distance from the floor to the bottom of the image area.+ 11 inches (280 mm)     total

  9. After confirming your image size, use tape or a pencil to mark the distance (c) from the top of the image area on the board to the bottom holes of the wall plate.

  10. Align the line (horizontal) on the template sheet with the (c) mark, then align the center line on the template sheet with the center of the image area. Follow the instructions on page 52 to install the projector.

Projection distance worksheets
The tables on the following pages provide installation information for select image sizes. The minimum ceiling height is based on an image 30 inches (762 mm) from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
Use the worksheets, the illustrations, and the information in the tables on the following pages to determine the projection distance and placement of the wall plate.

Diagonal image size and mounting position

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

In order to see the stamp and the numbers on the slider scale (b), you need to slide out the arm extension.

  • BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F: Mount it at the stamp when the image is less than 80 inches diagonally, or at the stamp when the projected image is 80 inches or more diagonally.
  • BrightLink EB-725Wi/EB-735Fi/EB-760Wi/EB-770Fi and PowerLite EB-720/EB-725W/EB-750F/EB-755F/EB-760W/EB-770F/EB-775F: Mount it at the stamp when the image is less than 90 inches diagonally, or at the stamp when the projected image is 90 inches or more diagonally.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F
Distance from top of projected image to wall plate
The distance (c) from the top of the projected image to the bottom mounting holes on the wall plate is the number given when the vertical slide is set to the base position, as shown below. Match the notch on the wall mount to the position of the stamp on the wall plate.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Installation measurement tables
See the following pages for your projector’s installation measurement tables:

  • BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F on page 29.
  • BrightLink EB-770Fi and PowerLite EB-770F/EB-775F on page 34.
  • BrightLink EB-735Fi and PowerLite EB-750F/EB-755F on page 39.
  • BrightLink EB-760Wi and PowerLite EB-760W on page 43.
  • BrightLink EB-725Wi and PowerLite EB-725W on page 46.
  • PowerLite EB-720 on page 49.

The measurements may differ depending on the location where you place the projector. When projecting in Tele mode, the quality of the projected images may decrease.
When projecting in the 16:6 (BrightLink 1485Fi/1485Fi+/EB-735Fi/EB-770Fi and PowerLite EB-750F/EB-755F/EB-770F/EB-775F/EB-800F/EB-805F) or 21:9 (BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+/EB-770Fi and PowerLite EB-770F/EB-775F/EB-800F/ EB-805F) aspect ratio, the projected image has black bars above and below it by default. You can use the Screen Position setting to move the projected image to the top of the screen and the black bars below the image. Note that the distance from the
top of the image to the bottom wall plate holes (c) or temporary wall plate hole (d) will vary if you change the Screen Position setting. The distance tables for the 16:6 and 21:9 aspect ratios include measurements for both the default Screen Position setting and measurements for an image that has been adjusted to sit at the top of the projection screen.
A shorter (x) distance may increase the minimum projection size. If the projection size is too small, there may not be enough space at the back of the projector for cable connections.

When you have determined the projection distance (a), check whether your cables will fit at the back of the projector. Calculate the distance from the wall plate cover to the back of the projector by using the following formula: (a) – (2.76 inches [70.2 mm]) + (x).

BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F
Measurements in Inches for 16:9

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
65”| 80.8| 56.7| 31.9| 6.2| 5.8| 7.9| 15.5
70″| 83.6| 61.0| 34.3| 7.5| 7.1| 8.2| 15.8
75″| 86.3| 65.4| 36.8| 8.7| 8.3| 8.5| 16.1
80″| 89.1| 69.7| 39.2| 10.0| 6.1| 8.9| 16.4
85″| 91.8| 74.1| 41.7| 11.2| 7.4| 9.2| 16.7
90″| 94.6| 78.4| 44.1| 12.4| 8.6| 9.5| 17.0
95”| 97.4| 82.8| 46.6| 13.7| 9.9| 9.8| 17.4
100”| 100.1| 87.2| 49.0| 15.0| 11.1| 10.1| 17.7
105”**| 103.0| 91.5| 51.5| 16.2| 12.4| 10.5| 18.0
110”**| 105.7| 95.9| 53.9| 17.4| 13.6| 10.8| 18.3
115”**| 108.5| 100.2| 56.4| 18.7| 14.9| 11.1| 18.7
120”**| 111.2| 104.6| 58.8| 19.9| 16.1| 11.4| 19.0
125”**| 114.0| 108.9| 61.3| 21.2| 17.4| 11.7| 19.3
130”****| 116.8| 113.3| 63.7| 22.4| 18.6| 12.0| 19.6

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 100”.
    Measurements in Centimeters for 16:9**

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
65”| 205.2| 143.9| 80.9| 15.8| 14.8| 20.1| 39.3
70 “| 212.3| 155.0| 87.2| 19.0| 18.0| 20.9| 40.1
75 “| 219.3| 166.0| 93.4| 22.1| 21.1| 21.7| 40.9
80 “| 226.3| 177.1| 99.6| 25.3| 15.6| 22.5| 41.7
85 “| 233.3| 188.2| 105.8| 28.5| 18.8| 23.3| 42.5
90 “| 240.4| 199.2| 112.1| 31.6| 21.9| 24.1| 43.3
95”| 247.4| 210.3| 118.3| 34.8| 25.1| 24.9| 44.1
100”| 254.4| 221.4| 124.5| 38.0| 28.3| 25.7| 44.9
105”**| 261.6| 232.4| 130.8| 41.1| 31.4| 26.6| 45.8
110”**| 268.6| 243.5| 137.0| 44.3| 34.6| 27.4| 46.6
115”**| 275.6| 254.6| 143.2| 47.5| 37.8| 28.2| 47.4
120”**| 282.6| 265.7| 149.4| 50.6| 40.9| 29.0| 48.2
125”**| 289.7| 276.7| 155.7| 53.8| 44.1| 29.8| 49.0
130”****| 296.7| 287.8| 161.9| 57.0| 47.3| 30.6| 49.8

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 100”.

BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F
Measurements in Inches for 16:6 (BL 1485Fi/1485Fi+ and PL EB-800F/EB- 805F)

| Default Screen Position| Screen Position max. (top)
---|---|---
Diagonal
 image
 size (S)| Min. ceiling
 **height*| Image
width (w)| Image
height (h)| Min. proj.
distance (a)| Sliderscale
mark (b)| Distance from
top of image
to bottom wall
plate holes (c)| Distance from
top of image to
temporary wall
plate hole (d)| Distance from
top of image
to bottom wall
plate holes (c)| Distance from
top of image to
temporary wall
plate hole (d)
65”| 77.7| 60.9| 22.8| 7.4| 7.0| 13.9| 21.5| 8.2| 15.7
70″| 80.3| 65.6| 24.6| 8.8| 8.4| 14.7| 22.2| 8.5| 16.1
75″| 82.8| 70.2| 26.3| 10.1| 9.7| 15.5| 23.0| 8.9| 16.5
80″| 85.3| 74.9| 28.1| 11.5| 7.6| 16.3| 23.8| 9.2| 16.8
85″| 87.9| 79.6| 29.8| 12.8| 9.0| 17.0| 24.6| 9.6| 17.2
90″| 90.4| 84.3| 31.6| 14.1| 10.3| 17.8| 25.4| 9.9| 17.5
95”| 93.0| 88.9| 33.3| 15.5| 11.7| 18.6| 26.2| 10.3| 17.8
100”| 95.5| 93.6| 35.1| 16.8| 13.0| 19.4| 26.9| 10.6| 18.1
105”| 98.0| 98.3| 36.9| 18.1| 14.3| 20.2| 27.7| 10.9| 18.5
110”| 100.6| 103.0| 38.6| 19.5| 15.7| 20.9| 28.5| 11.3| 18.9
115”| 103.1| 107.7| 40.4| 20.8| 17.0| 21.7| 29.3| 11.6| 19.2
120”**| 105.6| 112.4| 42.1| 22.2| 18.3| 22.5| 30.1| 12.0| 19.6

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Measurements in Centimeters for 16:6 (BL 1485Fi/1485Fi+ and PL EB-800/EB- 805F)

| Default Screen Position| Screen Position max. (top)
---|---|---
Diagonal
 image size (S)| Min.
 ceiling
 **height*| Image
width (w)| Image
height (h)| Min. proj.
distance (a)| Sliderscale
mark (b)| Distance from
top of image
to bottom wall
plate holes (c)| Distance from
top of image to
temporary wall
plate hole (d)| Distance from
top of image
to bottom wall
plate holes (c)| Distance from
top of image to
temporary wall
plate hole (d)
65”| 197.5| 154.6| 58.0| 18.9| 17.9| 35.3| 54.5| 20.8| 40.0
70 “| 203.9| 166.5| 62.4| 22.3| 21.3| 37.3| 56.5| 21.7| 40.9
75 “| 210.4| 178.4| 66.9| 25.7| 24.7| 39.3| 58.5| 22.6| 41.8
80 “| 216.8| 190.3| 71.3| 29.1| 19.4| 41.3| 60.5| 23.5| 42.7
85 “| 223.3| 202.2| 75.8| 32.5| 22.8| 43.3| 62.5| 24.4| 43.6
90 “| 229.8| 214.0| 80.3| 35.9| 26.2| 45.3| 64.5| 25.2| 44.4
95”| 236.2| 225.9| 84.7| 39.3| 29.6| 47.3| 66.5| 26.1| 45.3
100”| 242.6| 237.8| 89.2| 42.7| 33.0| 49.2| 68.4| 26.9| 46.1
105”| 249.0| 249.7| 93.6| 46.1| 36.4| 51.2| 70.4| 27.8| 47.0
110”| 255.5| 261.6| 98.1| 49.5| 39.8| 53.2| 72.4| 28.7| 47.9
115”| 262.0| 273.5| 102.6| 52.9| 43.2| 55.2| 74.4| 29.6| 48.8
120”**| 268.4| 285.4| 107.0| 56.3| 46.6| 57.2| 76.4| 30.5| 49.7

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F
Measurements in Inches for 16:10

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
61”| 81.3| 51.7| 32.3| 6.5| 6.1| 8.0| 15.5
65”| 83.7| 55.1| 344.4| 7.5| 7.1| 8.2| 15.8
70″| 86.7| 59.4| 37.1| 8.9| 8.5| 8.6| 16.1
75″| 89.7| 63.6| 39.8| 10.2| 9.8| 8.9| 16.5
80″| 92.7| 67.8| 42.4| 11.6| 7.8| 9.3| 16.9
85″| 95.6| 72.1| 45.0| 12.9| 9.1| 9.6| 17.2
90″| 98.7| 76.3| 47.7| 14.3| 10.5| 10.0| 17.5
95”| 101.7| 80.6| 50.4| 15.6| 11.8| 10.3| 17.9
100”| 104.7| 84.8| 53.0| 17.0| 13.1| 10.7| 18.2
105”**| 107.7| 89.1| 55.7| 18.3| 14.5| 11.0| 18.5
110”**| 110.6| 93.3| 58.3| 19.6| 15.8| 11.3| 18.9
115”**| 113.6| 97.5| 60.9| 21.0| 17.2| 11.7| 19.3
120”****| 116.6| 101.8| 63.6| 22.4| 18.5| 12.0| 19.6

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 100”.
    Measurements in Centimeters for 16:10**

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
61”| 206.5| 131.4| 82.1| 16.4| 15.4| 20.2| 39.4
65”| 212.6| 140.0| 87.5| 19.1| 18.1| 20.9| 40.1
70 “| 220.2| 150.8| 94.2| 22.6| 21.6| 21.8| 41.0
75 “| 227.9| 161.5| 101.0| 26.0| 25.0| 22.7| 41.9
80 “| 235.5| 172.3| 107.7| 29.4| 19.7| 23.6| 42.8
85 “| 243.0| 183.1| 114.4| 32.8| 23.1| 24.4| 43.6
90 “| 250.7| 193.9| 121.2| 36.3| 26.6| 25.3| 44.5
95”| 258.3| 204.7| 127.9| 39.7| 30.0| 26.2| 45.4
100”| 265.9| 215.4| 134.6| 43.1| 33.4| 27.1| 46.3
105”**| 273.5| 226.2| 141.4| 46.5| 36.8| 27.9| 47.1
110”**| 281.1| 236.9| 148.1| 49.9| 40.2| 28.8| 48.0
115”**| 288.7| 247.7| 154.8| 53.4| 43.7| 29.7| 48.9
120”****| 296.3| 258.5| 161.5| 56.8| 47.1| 30.6| 49.8

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 100”.

BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F
Measurements in Inches for 4:3

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
65”| 88.8| 52.0| 39.0| 9.8| 9.4| 8.8| 16.4
70″| 92.2| 56.0| 42.0| 11.4| 11.0| 9.2| 16.8
75″| 95.6| 60.0| 45.0| 12.9| 12.5| 9.6| 17.2
80″| 99.0| 64.0| 48.0| 14.4| 10.6| 10.0| 17.6
85”| 102.4| 68.0| 51.0| 15.9| 12.1| 10.4| 18.0
90”| 105.8| 72.0| 54.0| 17.5| 13.7| 10.8| 18.3
95”| 109.2| 76.0| 57.0| 19.0| 15.2| 11.2| 18.7
100”| 112.6| 80.0| 60.0| 20.5| 16.7| 11.6| 19.1
105”****| 116.0| 84.0| 63.0| 22.0| 18.2| 12.0| 19.5

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 100”.
    Measurements in Centimeters for 4:3**

Diagonal image size (S)| Min. ceiling height**| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
65”| 225.7| 132.1| 99.1| 25.0| 24.0| 22.4| 41.6
70 “| 234.3| 142.2| 106.7| 28.9| 27.9| 23.4| 42.6
75 “| 242.9| 152.4| 114.3| 32.8| 31.8| 24.4| 43.6
80 “| 251.5| 162.6| 121.9| 36.6| 26.9| 25.4| 44.6
85”| 260.1| 172.7| 129.5| 40.5| 30.8| 26.4| 45.6
90”| 268.8| 182.9| 137.2| 44.4| 34.7| 27.4| 46.6
95”| 259.4| 193.0| 144.8| 48.3| 38.6| 28.4| 47.6
100”| 268.0| 203.2| 152.4| 52.1| 42.4| 29.4| 48.6
105”**| 276.6| 213.4| 160.0| 56.0| 46.3| 30.4| 49.6

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 100”.

BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F
Measurements in Inches for 21:9

| Default Screen Position| Screen Position max. (top)
---|---|---
Diagonal image size (S)| **Min. ceiling height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
65”| 78.7| 59.8| 25.6| 7.1| 6.7| 12.1| 19.7| 8.1| 15.7
70″| 81.3| 64.3| 27.6| 8.4| 8.0| 12.8| 20.3| 8.5| 16.0
75″| 84.0| 68.9| 29.5| 9.7| 9.3| 13.4| 21.0| 8.8| 16.4
80″| 86.6| 73.5| 31.5| 11.1| 7.2| 14.1| 21.6| 9.1| 16.7
85″| 89.2| 78.1| 33.5| 12.4| 8.5| 14.7| 22.3| 9.5| 17.0
90″| 91.8| 82.7| 35.4| 13.7| 9.8| 15.4| 22.9| 9.8| 17.4
95”| 94.4| 87.3| 37.4| 15.0| 11.2| 16.0| 23.5| 10.1| 17.7
100”| 97.1| 91.9| 39.4| 16.3| 12.5| 16.7| 24.2| 10.5| 18.1
105”**| 99.7| 96.5| 41.4| 17.6| 13.8| 17.3| 24.8| 10.8| 18.4
110”**| 102.3| 101.1| 43.3| 18.9| 15.1| 17.9| 25.5| 11.1| 18.7
115”**| 104.9| 105.7| 45.3| 20.2| 16.4| 18.6| 26.1| 11.5| 19.1
120”****| 107.5| 110.3| 47.3| 21.6| 17.8| 19.2| 26.8| 11.8| 19.4

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 100”.
    Measurements in Centimeters for 21:9**

| Default Screen Position| Screen Position max. (top)
---|---|---
Diagonal image size (S)| **Min. ceiling height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
65”| 200.0| 151.8| 65.0| 18.1| 17.1| 30.8| 50.0| 20.6| 39.8
70 “| 206.6| 163.4| 70.0| 21.4| 20.4| 32.4| 51.6| 21.5| 40.7
75 “| 213.3| 175.1| 75.0| 24.7| 23.7| 34.1| 53.3| 22.4| 41.6
80 “| 219.9| 186.8| 80.0| 28.1| 18.4| 35.7| 54.9| 23.2| 42.4
85 “| 226.6| 198.4| 85.0| 31.4| 21.7| 37.4| 56.5| 24.1| 43.3
90 “| 233.2| 210.1| 90.0| 34.7| 25.0| 39.0| 58.2| 24.9| 44.1
95”| 239.9| 221.8| 95.1| 38.1| 28.4| 40.6| 59.8| 25.7| 44.9
100”| 246.6| 233.5| 100.1| 41.4| 31.7| 42.3| 61.5| 26.7| 45.9
105”**| 253.2| 245.1| 105.1| 44.8| 35.1| 43.9| 63.1| 27.5| 46.7
110”**| 259.8| 256.8| 110.1| 48.1| 38.4| 45.5| 64.7| 28.3| 47.5
115”**| 266.5| 268.5| 115.1| 51.4| 41.7| 47.2| 66.4| 29.2| 48.4
120”****| 273.1| 280.2| 120.1| 54.8| 45.1| 48.8| 68.0| 30.0| 49.2

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 100”

BrightLink EB-770Fi and PowerLite EB-770F/EB-775F
Measurements in Inches for 16:9

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
71″| 84.5| 61.9| 34.8| 3.5| 5.8| 8.7| 16.3
75″| 86.9| 65.4| 36.8| 4.5| 6.8| 9.2| 16.7
80″| 90.0| 69.7| 39.2| 5.7| 8.0| 9.8| 17.3
85″| 93.0| 74.1| 41.7| 6.9| 9.3| 10.4| 17.9
90″| 96.1| 78.4| 44.4| 8.2| 7.1| 10.9| 18.5
95”| 99.1| 82.8| 46.6| 9.5| 8.3| 11.5| 19.1
100”| 102.1| 87.2| 49.0| 10.7| 9.6| 12.1| 19.7
105”**| 105.2| 91.5| 51.5| 11.9| 10.8| 12.7| 20.2
110”**| 108.2| 95.9| 53.9| 13.2| 12.1| 13.3| 20.8
115”**| 111.2| 100.2| 56.4| 14.4| 13.3| 13.9| 21.4
120”**| 114.3| 104.6| 58.8| 15.6| 14.5| 14.5| 22.0
125”**| 117.3| 108.9| 61.3| 16.9| 15.8| 15.0| 22.6
130”**| 120.4| 113.3| 63.7| 18.1| 17.0| 15.6| 23.2
135”**| 123.4| 117.7| 66.2| 19.4| 18.3| 16.2| 23.8
140”****| 126.4| 122.0| 68.6| 20.6| 19.5| 16.8| 24.4

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 100”.
    Measurements in Centimeters for 16:9**

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
71″| 214.6| 157.2| 88.4| 8.8| 14.7| 22.1| 41.3
75″| 220.8| 166.0| 93.4| 11.3| 17.2| 23.3| 42.5
80″| 228.5| 177.1| 99.6| 14.5| 20.4| 24.8| 44.0
85″| 236.2| 188.2| 105.8| 17.6| 23.5| 26.3| 45.5
90″| 244.0| 199.2| 112.1| 20.8| 18.0| 27.8| 47.0
95”| 251.6| 210.3| 118.3| 24.0| 21.1| 29.2| 48.5
100”| 259.3| 221.4| 124.5| 27.1| 24.3| 30.7| 50.0
105”**| 267.1| 232.4| 130.8| 30.3| 27.4| 32.2| 51.4
110”**| 274.8| 243.5| 137| 33.4| 30.6| 33.7| 52.9
115”**| 282.5| 254.6| 143.2| 36.6| 33.8| 35.2| 54.4
120”**| 290.2| 265.7| 149.4| 39.7| 36.9| 36.7| 55.9
125”**| 298.0| 276.7| 155.7| 42.9| 40.1| 38.2| 57.4
130”**| 305.7| 287.8| 161.9| 46.0| 43.2| 39.7| 58.9
135”**| 313.3| 298.9| 168.1| 49.2| 46.4| 41.1| 60.4
140”****| 321.0| 309.9| 174.3| 52.3| 49.5| 42.6| 61.9

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 100”.

BrightLink EB-770Fi and PowerLite EB-770F/EB-775F
Measurements in Inches for 16:6

| Default Screen Position| Screen Position max. (top)
---|---|---
Diagonal image size (S)| **Min. ceiling height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
66”| 78.7| 61.8| 23.2| 3.4| 5.8| 14.5| 22.1| 8.7| 16.3
70”| 80.9| 65.6| 24.6| 4.5| 6.8| 15.4| 22.9| 9.2| 16.8
75″| 83.8| 70.2| 26.3| 5.8| 8.2| 16.4| 24.0| 5.9| 17.4
80″| 86.6| 74.9| 28.1| 7.2| 9.5| 17.5| 25.0| 10.4| 18.0
85″| 89.4| 79.6| 29.8| 8.5| 10.8| 18.5| 26.1| 11.1| 18.7
90″| 92.2| 84.3| 31.6| 9.8| 8.7| 19.6| 27.2| 11.7| 19.3
95″| 95.0| 88.9| 33.4| 11.2| 10.1| 20.7| 28.2| 12.3| 19.9
100”| 97.9| 93.6| 35.1| 12.5| 11.4| 21.7| 29.3| 13.0| 20.6
105”| 100.7| 98.3| 36.9| 13.9| 12.7| 22.8| 30.4| 13.6| 21.2
110”| 103.5| 103.0| 38.6| 15.2| 14.1| 23.9| 31.5| 14.2| 21.8
115”**| 106.4| 107.7| 40.4| 16.5| 15.4| 25.0| 32.5| 14.8| 22.4
120”**| 106.2| 112.4| 42.1| 17.8| 16.7| 26.0| 33.6| 15.5| 23.1
125”**| 112.0| 117.1| 43.9| 19.2| 18.1| 27.1| 34.7| 16.1| 23.7
130”****| 114.8| 121.7| 45.6| 20.5| 19.4| 28.2| 35.7| 16.7| 24.3

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 110”.
    Measurements in Centimeters for 16:6**

| Default Screen Position| Screen Position max. (top)
---|---|---
Diagonal image size (S)| **Min. ceiling height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
66”| 199.8| 157.0| 58.9| 8.7| 14.6| 36.8| 56.0| 22.1| 41.3
70”| 205.5| 166.5| 62.4| 11.4| 17.3| 39.0| 58.2| 23.3| 42.6
75″| 212.7| 178.4| 66.9| 14.8| 20.7| 41.7| 60.9| 14.9| 44.2
80″| 219.8| 190.3| 71.3| 18.2| 24.1| 44.4| 63.6| 26.5| 45.8
85″| 227.0| 202.2| 75.8| 21.6| 27.5| 47.1| 66.3| 28.1| 47.4
90″| 234.2| 214.0| 80.3| 25.0| 22.2| 49.8| 69.0| 29.7| 49.0
95″| 241.3| 225.9| 84.7| 28.4| 25.6| 52.5| 71.7| 31.3| 50.6
100”| 248.5| 237.8| 89.2| 31.8| 28.9| 55.2| 74.5| 32.9| 52.2
105”| 255.7| 249.7| 93.6| 35.2| 32.3| 58.0| 77.2| 34.5| 53.8
110”| 262.9| 261.6| 98.1| 38.5| 35.7| 60.7| 79.9| 36.1| 55.4
115”**| 270.1| 273.5| 102.6| 41.9| 39.1| 63.4| 82.6| 37.7| 57.0
120”**| 277.2| 285.4| 107.0| 45.3| 42.5| 66.1| 85.3| 39.3| 58.6
125”**| 284.4| 297.3| 111.5| 48.7| 45.9| 68.8| 88.0| 40.9| 60.2
130”****| 291.5| 309.2| 115.9| 52.1| 49.3| 71.5| 90.7| 42.5| 61.8

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 110”.

BrightLink EB-770Fi and PowerLite EB-770F/EB-775F
Measurements in Inches for 16:10

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
66″| 84.7| 56.0| 35.0| 3.5| 5.9| 8.7| 16.3
70”| 87.3| 59.4| 37.1| 4.6| 6.9| 9.3| 16.8
75″| 90.7| 63.6| 39.8| 5.9| 8.3| 9.9| 17.4
80″| 93.9| 67.8| 42.4| 7.3| 9.6| 10.5| 18.1
85″| 97.2| 72.1| 45.0| 8.7| 10.9| 11.1| 18.7
90″| 100.5| 76.3| 47.7| 10.0| 8.9| 11.8| 19.3
95”| 103.8| 80.6| 50.4| 11.3| 10.2| 12.4| 20.0
100”| 107.0| 84.8| 53.0| 12.7| 11.6| 13.0| 20.6
105”**| 110.4| 89.1| 55.7| 14.0| 12.9| 13.7| 21.3
110”**| 113.6| 93.3| 58.3| 15.4| 14.3| 14.3| 21.9
115”**| 116.9| 97.5| 60.9| 16.7| 15.6| 15.0| 22.5
120”**| 120.2| 101.8| 63.6| 18.0| 16.9| 15.6| 23.2
125”**| 123.5| 106.0| 66.3| 19.4| 18.3| 16.2| 23.8
130”****| 126.8| 110.2| 68.9| 20.7| 19.6| 16.9| 24.4

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 100”.
    Measurements in Centimeters for 16:10**

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
66″| 215.1| 142.2| 88.8| 9.0| 14.9| 22.2| 41.4
70”| 221.8| 150.8| 94.2| 11.7| 17.6| 23.5| 42.7
75″| 230.2| 161.5| 101.0| 15.1| 21.0| 25.1| 44.3
80″| 238.5| 172.3| 107.7| 18.6| 24.4| 26.7| 45.9
85″| 246.8| 183.1| 114.4| 22.0| 27.8| 28.3| 47.5
90″| 255.2| 193.9| 121.2| 25.4| 22.6| 29.9| 49.1
95”| 263.5| 204.6| 127.9| 28.8| 26.0| 31.5| 50.8
100”| 271.8| 215.4| 134.6| 32.2| 29.4| 33.1| 52.4
105”**| 280.3| 226.2| 141.4| 35.6| 32.8| 34.8| 54.0
110”**| 288.6| 236.9| 148.1| 39.0| 36.2| 36.4| 55.6
115”**| 296.9| 247.7| 154.8| 42.4| 39.6| 38.0| 57.2
120”**| 305.2| 258.5| 161.5| 45.8| 43.0| 39.6| 58.8
125”**| 313.6| 269.2| 168.3| 49.2| 46.4| 41.2| 60.4
130”****| 321.9| 280.0| 175.0| 52.6| 49.8| 42.8| 62.0

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 100”.

BrightLink EB-770Fi and PowerLite EB-770F/EB-775F
Measurements in Inches for 4:3

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
60”| 86.0| 48.0| 36.0| 4.1| 6.4| 9.0| 16.5
65”| 89.7| 52.0| 39.0| 5.6| 7.9| 9.7| 17.3
70″| 93.4| 56.0| 42.0| 7.1| 9.4| 10.4| 18.0
75″| 97.1| 60.0| 45.0| 8.6| 10.9| 11.1| 18.7
80″| 100.8| 64.0| 48.0| 10.2| 12.4| 11.9| 19.4
85″| 104.5| 68.0| 51.0| 11.7| 14.0| 12.6| 20.1
90″| 108.3| 72.0| 54.0| 13.2| 12.1| 13.3| 20.9
95”| 112.0| 76.0| 57.0| 14.7| 13.6| 14.0| 21.6
100”| 115.7| 80.0| 60.0| 16.2| 15.1| 14.7| 22.3
105”**| 119.4| 84.0| 63.0| 17.8| 16.6| 15.4| 23.0
110”**| 123.1| 88.0| 66.0| 19.3| 18.2| 16.1| 23.7
115”****| 126.9| 92.0| 69.0| 20.8| 19.7| 16.9| 24.5

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 100”.
    Measurements in Centimeters for 4:3**

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
60”| 218.3| 121.9| 91.4| 10.3| 16.2| 22.8| 42.0
65”| 227.8| 132.1| 99.1| 14.2| 20.1| 24.6| 43.9
70″| 237.3| 142.2| 106.7| 18.0| 23.9| 26.5| 45.7
75″| 246.7| 152.4| 114.3| 21.9| 27.8| 28.3| 47.5
80″| 256.1| 162.6| 121.9| 25.8| 31.6| 30.1| 49.3
85″| 265.5| 172.7| 129.5| 29.6| 35.5| 31.9| 51.1
90”| 275.1| 182.9| 137.2| 33.5| 30.7| 33.8| 53.0
95”| 284.5| 193.0| 144.8| 37.3| 34.5| 35.6| 54.8
100”| 293.9| 203.2| 152.4| 41.2| 38.4| 37.4| 56.6
105”**| 303.3| 213.4| 160.0| 45.1| 42.2| 39.2| 58.4
110”**| 312.7| 223.5| 167.6| 48.9| 46.1| 41.0| 60.3
115”****| 322.3| 233.7| 175.3| 52.8| 50.0| 42.9| 62.1

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 100”.

BrightLink EB-770Fi and PowerLite EB-770F/EB-775F
Measurements in Inches for 21:9

| Default Screen Position| Screen Position max. (top)
---|---|---
Diagonal image size (S)| **Min. ceiling height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
70”| 78.9| 65.6| 24.6| 4.2| 6.5| 13.4| 20.9| 10.8| 18.4
75″| 81.6| 70.2| 26.3| 5.5| 7.8| 14.3| 21.9| 11.5| 19.1
80″| 84.3| 74.9| 28.1| 6.8| 9.1| 15.2| 22.8| 12.3| 19.8
85″| 86.9| 79.6| 29.8| 8.1| 10.4| 16.1| 23.7| 13.0| 20.6
90″| 89.7| 84.3| 31.6| 9.4| 8.3| 17.1| 24.6| 13.8| 21.3
95″| 92.3| 88.9| 33.4| 10.7| 9.6| 18.0| 25.6| 14.5| 22.1
100”| 95.0| 93.6| 35.1| 12.0| 10.9| 18.9| 26.5| 15.2| 22.8
105”| 97.7| 98.3| 36.9| 13.3| 12.2| 19.8| 27.4| 16.0| 23.6
110”| 100.4| 103.0| 38.6| 14.7| 13.5| 20.8| 28.3| 16.7| 24.3
115”**| 103.1| 107.7| 40.4| 15.9| 14.8| 21.7| 29.3| 17.5| 25.0
120”**| 105.7| 112.4| 42.1| 17.2| 16.1| 22.6| 30.2| 18.2| 25.8
125”**| 108.4| 117.1| 43.9| 18.5| 17.4| 23.5| 31.1| 19.1| 26.5
130”**| 111.1| 121.7| 45.6| 19.9| 18.8| 24.5| 32.0| 19.7| 27.3
135”****| 119.5| 124.1| 53.2| 21.2| 20.1| 25.4| 33.0| 20.5| 28.0

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 110”.
    Measurements in Centimeters for 21:9**

| Default Screen Position| Screen Position max. (top)
---|---|---
Diagonal image size (S)| **Min. ceiling height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
70 “| 200.4| 166.5| 62.4| 10.6| 16.5| 33.9| 53.1| 27.4| 46.6
75 “| 207.2| 178.4| 66.9| 13.9| 19.8| 36.2| 55.5| 29.3| 48.5
80 “| 214.0| 190.3| 71.3| 17.2| 23.1| 38.6| 57.8| 31.2| 50.4
85 “| 220.8| 202.2| 75.8| 20.5| 26.4| 40.9| 60.2| 33.1| 52.3
90 “| 227.4| 214| 80.3| 23.9| 21.1| 43.3| 62.5| 35.0| 54.2
95”| 234.4| 225.9| 84.7| 27.2| 24.4| 45.6| 64.9| 36.9| 56.1
100”| 241.3| 237.8| 89.2| 30.5| 27.7| 48.0| 67.2| 38.7| 58.0
105”| 248.0| 249.7| 93.6| 33.8| 31.0| 50.3| 69.6| 40.6| 59.9
110”| 254.9| 261.6| 98.1| 37.2| 34.4| 52.7| 71.9| 42.5| 61.7
115”**| 261.7| 273.5| 102.6| 40.5| 37.7| 55.0| 74.3| 44.4| 63.6
120”**| 268.5| 285.4| 107.0| 43.8| 41.0| 57.4| 76.6| 46.3| 65.5
125”**| 275.3| 297.3| 111.5| 47.1| 44.3| 59.7| 79.0| 48.2| 67.4
130”**| 282.1| 309.2| 115.9| 50.5| 47.7| 62.1| 81.3| 50.1| 69.3
135”****| 303.6| 315.2| 135.1| 53.8| 51.0| 64.4| 83.7| 52.0| 71.2

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 110”.

BrightLink EB-735Fi and PowerLite EB-750F/EB-755F
Measurements in Inches for 16:9

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
70″| 84.3| 61.0| 34.3| 3.4| 5.7| 8.9| 16.5
75″| 87.3| 65.4| 36.8| 4.6| 6.9| 9.6| 17.1
80″| 90.4| 69.7| 39.2| 5.8| 8.1| 10.2| 17.7
85″| 93.4| 74.1| 41.7| 7.0| 9.3| 10.8| 18.3
90″| 96.5| 78.4| 44.1| 8.1| 7.0| 11.4| 19.0
95”| 99.6| 82.8| 46.6| 9.3| 8.2| 12.0| 19.6
100”| 102.6| 87.2| 49.0| 10.5| 9.4| 12.6| 20.2
105”**| 105.7| 91.5| 51.5| 11.7| 10.6| 13.2| 20.8
110”**| 108.8| 95.9| 53.9| 12.9| 11.8| 13.9| 21.4
115”**| 111.8| 100.2| 56.4| 14.1| 13.0| 14.4| 22.0
120”**| 114.9| 104.6| 58.8| 15.2| 14.1| 15.1| 22.6
125”**| 118.0| 109.0| 61.3| 16.4| 15.3| 15.7| 23.2
130”****| 121.0| 113.3| 63.7| 17.6| 16.5| 16.3| 23.9

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 100”.
    Measurements in Centimeters for 16:9**

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
70 “| 214.1| 155.0| 87.2| 8.7| 14.5| 22.7| 41.9
75 “| 221.9| 166.0| 93.4| 11.7| 17.5| 24.3| 43.5
80 “| 229.6| 177.1| 99.6| 14.7| 20.6| 25.8| 45.0
85 “| 237.4| 188.2| 105.8| 17.7| 23.6| 27.4| 46.6
90 “| 245.2| 199.2| 112.1| 20.7| 17.9| 28.9| 48.2
95”| 253.0| 210.3| 118.3| 23.7| 20.9| 30.5| 49.7
100”| 260.7| 221.4| 124.5| 26.7| 23.9| 32.0| 51.3
105”**| 268.6| 232.5| 130.8| 29.7| 26.9| 33.6| 52.8
110”**| 276.4| 243.6| 137.0| 32.7| 29.9| 35.2| 54.4
115”**| 284.1| 254.6| 143.2| 35.7| 32.9| 36.7| 55.9
120”**| 291.9| 265.6| 149.4| 38.7| 35.9| 38.3| 57.5
125”**| 299.7| 276.8| 155.7| 41.7| 38.9| 39.8| 59.0
130”****| 307.5| 287.8| 161.9| 44.7| 41.9| 41.4| 60.6

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 100”.

BrightLink EB-735Fi and PowerLite EB-750F/EB-755F
Measurements in Inches for 16:6

| Default Screen Position| Screen Position max. (top)
---|---|---
Diagonal
 image
 size (S)| Min.
 ceiling
 **height*| Image
width (w)| Image
height (h)| Min. proj.
distance (a)| Sliderscale
mark (b)| Distance from
top of image
to bottom wall
plate holes (c)| Distance from
top of image to
temporary wall
plate hole (d)| Distance from
top of image
to bottom wall
plate holes (c)| Distance from
top of image to
temporary wall
plate hole (d)
65”| 78.5| 60.9| 22.8| 3.4| 5.7| 14.6| 22.2| 8.9| 16.5
70″| 81.3| 65.6| 24.6| 4.6| 7.0| 15.7| 23.3| 9.6| 17.2
75″| 84.1| 70.2| 26.3| 5.9| 8.2| 16.8| 24.4| 10.2| 17.8
80″| 87.0| 74.9| 28.1| 7.2| 9.5| 17.9| 25.5| 10.9| 18.5
85″| 89.9| 79.6| 29.8| 8.5| 10.8| 19.0| 26.6| 11.5| 19.1
90″| 92.7| 84.3| 31.6| 9.7| 8.6| 20.1| 27.7| 12.2| 19.8
95”| 95.6| 88.9| 33.3| 11.0| 9.9| 21.2| 28.8| 12.9| 20.4
100”| 98.4| 93.6| 35.1| 12.2| 11.1| 22.3| 29.9| 13.5| 21.1
105”| 101.2| 98.3| 36.9| 13.5| 12.4| 23.4| 31.0| 14.2| 21.7
110”**| 104.1| 103.0| 38.6| 14.8| 13.7| 24.5| 32.0| 14.8| 22.4

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Measurements in Centimeters for 16:6

| Default Screen Position| Screen Position max. (top)
---|---|---
Diagonal
 image
 size (S)| Min.
 ceiling
 **height*| Image
width
(w)| Image
height
(h)| Min. proj.
distance
(a)| Sliderscale
mark (b)| Distance from
top of image
to bottom wall
plate holes (c)| Distance from
top of image to
temporary wall
plate hole (d)| Distance from
top of image
to bottom wall
plate holes (c)| Distance from
top of image to
temporary wall
plate hole (d)
65”| 199.4| 154.6| 58.0| 8.6| 14.4| 37.2| 56.4| 22.7| 41.9
70 “| 206.5| 166.5| 62.4| 11.8| 17.7| 39.9| 59.2| 24.3| 43.6
75 “| 213.8| 178.4| 66.9| 15.0| 20.9| 42.7| 61.9| 26.0| 45.2
80 “| 221.0| 190.3| 71.3| 18.2| 24.1| 45.5| 64.7| 27.7| 46.9
85 “| 228.3| 202.2| 75.8| 21.5| 27.4| 48.3| 67.5| 29.3| 48.6
90 “| 235.6| 214.0| 80.3| 24.7| 21.9| 51.1| 70.3| 31.0| 50.2
95”| 242.8| 225.9| 84.7| 27.9| 25.1| 53.9| 73.1| 32.7| 51.9
100”| 250.1| 237.8| 89.2| 31.1| 28.3| 56.7| 75.9| 34.4| 53.6
105”| 257.2| 249.7| 93.6| 34.4| 31.6| 59.4| 78.7| 36.0| 55.2
110”**| 264.5| 261.6| 98.1| 37.5| 34.8| 62.2| 81.4| 37.7| 56.9

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

BrightLink EB-735Fi and PowerLite EB-750F/EB-755F
Measurements in Inches for 16:10

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
65”| 84.4| 55.1| 34.4| 3.5| 5.8| 9.0| 16.5
70″| 87.7| 59.3| 37.1| 4.8| 7.1| 9.6| 17.2
75″| 91.1| 63.6| 39.8| 6.0| 8.3| 10.3| 17.9
80″| 94.3| 67.8| 42.4| 7.3| 9.6| 10.9| 18.5
85″| 97.7| 72.1| 45.0| 8.6| 10.9| 11.6| 19.2
90″| 101.0| 76.3| 47.7| 9.9| 8.7| 12.3| 19.8
95”| 104.3| 80.6| 50.4| 11.1| 10.0| 13.0| 20.5
100”| 107.6| 84.8| 53.0| 12.4| 11.3| 13.6| 21.2
105”| 110.9| 89.1| 55.7| 13.7| 12.6| 14.3| 21.9
110”**| 114.2| 93.3| 58.3| 15.0| 13.9| 14.9| 22.5

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Measurements in Centimeters for 16:10

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
65”| 214.5| 140.0| 87.5| 8.8| 14.7| 22.8| 42.0
70 “| 222.9| 150.7| 94.2| 12.1| 18.0| 24.5| 43.7
75 “| 231.4| 161.6| 101.0| 15.3| 21.2| 26.2| 45.4
80 “| 239.7| 172.3| 107.7| 18.6| 24.4| 27.8| 47.1
85 “| 248.1| 183.0| 114.4| 21.8| 27.7| 29.5| 48.7
90 “| 256.6| 193.9| 121.2| 25.1| 22.2| 31.2| 50.4
95”| 265.0| 204.6| 127.9| 28.3| 25.5| 32.9| 52.1
100”| 273.4| 215.4| 134.6| 31.6| 28.7| 34.6| 53.8
105”| 281.8| 226.2| 141.4| 34.8| 32.0| 36.2| 55.5
110”**| 290.2| 237.0| 148.1| 38.1| 35.2| 37.9| 57.1

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

BrightLink EB-735Fi and PowerLite EB-750F/EB-755F
Measurements in Inches for 4:3

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
55”| 82.6| 44.0| 33.0| 2.8| 5.1| 8.6| 16.2
60”| 86.4| 48.0| 36.0| 4.2| 6.5| 9.4| 16.9
65”| 88.8| 52.0| 39.0| 5.7| 8.0| 10.1| 17.7
70″| 93.9| 56.0| 42.0| 7.1| 9.4| 10.9| 18.4
75″| 97.6| 60.0| 45.0| 8.6| 10.9| 11.6| 19.2
80″| 101.4| 64.0| 48.0| 10.0| 12.3| 12.4| 19.9
85”| 105.1| 68.0| 51.0| 11.5| 13.8| 13.1| 20.7
90”| 108.9| 72.0| 54.0| 12.9| 11.8| 13.9| 21.4
95”**| 112.6| 76.0| 57.0| 14.4| 13.2| 14.6| 22.2

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Measurements in Centimeters for 4:3

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
55”| 209.9| 111.7| 83.8| 7.0| 12.9| 21.9| 41.1
60”| 219.4| 121.9| 91.4| 10.7| 16.6| 23.8| 43.0
65”| 229.0| 132.1| 99.1| 14.4| 20.3| 25.7| 44.9
70 “| 238.5| 142.2| 106.7| 18.1| 24.0| 27.6| 46.8
75 “| 248.0| 152.4| 114.3| 21.8| 27.6| 29.5| 48.7
80 “| 257.5| 162.6| 121.9| 25.4| 31.3| 31.4| 50.6
85”| 267.0| 172.7| 129.5| 29.1| 35.0| 33.3| 52.5
90”| 276.6| 182.9| 137.2| 32.8| 30.0| 35.2| 54.4
95”**| 286.1| 193.1| 144.8| 36.5| 33.6| 37.1| 56.3

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

BrightLink EB-760Wi and PowerLite EB-760W
Measurements in Inches for 16:10

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
70″| 86.2| 59.4| 37.1| 3.9| 6.2| 8.1| 15.7
75″| 89.4| 63.6| 39.8| 5.2| 7.5| 8.7| 16.2
80″| 92.6| 67.8| 42.4| 6.4| 8.7| 9.2| 16.8
85″| 95.8| 72.1| 45.0| 7.7| 10.0| 9.8| 17.3
90″| 99.0| 76.3| 47.7| 9.0| 7.9| 10.3| 17.9
95”| 102.2| 80.6| 50.4| 10.3| 9.2| 10.9| 18.4
100”| 105.4| 84.8| 53.0| 11.6| 10.5| 11.4| 19.0
105”**| 108.6| 89.1| 55.7| 12.9| 11.8| 12.0| 19.5
110”**| 111.8| 93.3| 58.3| 14.2| 13.0| 12.5| 20.1
115”**| 115.0| 97.5| 60.9| 15.4| 14.3| 13.1| 20.6
120”**| 118.2| 101.8| 63.6| 16.7| 15.6| 13.6| 21.2
125”**| 121.4| 106.0| 66.3| 18.0| 16.9| 14.2| 21.7
130”**| 124.6| 110.2| 68.9| 19.3| 18.2| 14.7| 22.3
135”****| 127.8| 114.5| 71.5| 20.6| 19.5| 15.3| 22.9

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 100”.
    Measurements in Centimeters for 16:10**

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
70 “| 218.9| 150.8| 94.2| 9.8| 15.7| 20.6| 39.8
75 “| 227.1| 161.5| 101.0| 13.1| 19.0| 22.0| 41.2
80 “| 235.2| 172.3| 107.7| 16.3| 22.2| 23.4| 42.6
85 “| 243.3| 183.1| 114.4| 19.6| 25.5| 24.8| 44.0
90 “| 251.5| 193.9| 121.2| 22.9| 20.1| 26.2| 45.4
95”| 259.6| 204.6| 127.9| 26.2| 23.3| 27.6| 46.8
100”| 267.7| 215.4| 134.6| 29.4| 26.6| 29.0| 48.2
105”**| 275.9| 226.2| 141.4| 32.7| 29.9| 30.4| 49.6
110”**| 284.0| 236.9| 148.1| 36.0| 33.1| 31.8| 51.0
115”**| 292.1| 247.7| 154.8| 39.2| 36.4| 33.2| 52.4
120”**| 300.2| 258.5| 161.5| 42.5| 39.7| 34.6| 53.8
125”**| 308.4| 269.2| 168.3| 45.8| 42.9| 36.0| 55.2
130”**| 316.5| 280.0| 175.0| 49.0| 46.2| 37.4| 56.6
135”****| 324.6| 290.8| 181.7| 52.3| 49.5| 38.8| 58.1

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 100”.

BrightLink EB-760Wi and PowerLite EB-760W
Measurements in Inches for 16:9

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
70″| 85.6| 61.0| 34.3| 4.4| 6.7| 10.2| 17.8
75″| 88.7| 65.4| 36.8| 5.7| 8.0| 10.9| 18.5
80″| 91.9| 69.7| 39.2| 7.0| 9.3| 11.7| 19.2
85”| 95.0| 74.1| 41.7| 8.4| 10.6| 12.3| 19.9
90″| 98.2| 78.4| 44.1| 9.7| 8.5| 13.0| 20.6
95”| 101.3| 82.8| 46.6| 11.0| 9.9| 13.7| 21.3
100”| 104.5| 87.2| 49.0| 12.3| 11.2| 14.5| 22.0
105”**| 107.7| 91.5| 51.5| 13.6| 12.5| 15.2| 22.7
110”**| 110.8| 95.9| 53.9| 15.0| 13.8| 15.9| 23.4
115”**| 114.0| 100.2| 56.4| 16.3| 15.2| 16.6| 24.1
120”**| 117.1| 104.6| 58.8| 17.6| 16.5| 17.3| 24.8
125”**| 120.3| 108.9| 61.3| 18.9| 17.8| 18.0| 25.6
130”**| 123.4| 113.3| 63.7| 20.2| 19.1| 18.7| 26.3
134”****| 126.0| 116.8| 65.7| 21.3| 20.2| 19.3| 26.8

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 100”.
    Measurements in Centimeters for 16:9**

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
70 “| 217.3| 155.0| 87.2| 11.1| 17.0| 26.0| 45.2
75 “| 225.3| 166.0| 93.4| 14.4| 20.3| 27.8| 47.0
80 “| 233.3| 177.1| 99.6| 17.8| 23.7| 29.6| 48.8
85 “| 241.2| 188.2| 105.8| 21.2| 27.0| 31.3| 50.6
90 “| 249.3| 199.2| 112.1| 24.5| 21.7| 33.1| 52.4
95”| 257.3| 210.3| 118.3| 27.9| 25.1| 34.9| 54.1
100”| 265.3| 221.4| 124.5| 31.2| 28.4| 36.7| 55.9
105”**| 273.4| 232.4| 130.8| 34.6| 31.8| 38.5| 57.7
110”**| 281.4| 243.5| 137.0| 38.0| 35.1| 40.3| 59.5
115”**| 289.4| 254.6| 143.2| 41.3| 38.5| 42.1| 61.3
120”**| 297.4| 265.7| 149.4| 44.7| 41.9| 43.9| 63.1
125”**| 305.4| 276.7| 155.7| 48.0| 45.2| 45.6| 64.9
130”**| 313.4| 287.8| 161.9| 51.4| 48.6| 47.4| 66.7
134”****| 319.9| 296.6| 166.9| 54.1| 51.3| 48.9| 68.1

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 100”.

BrightLink EB-760Wi and PowerLite EB-760W
Measurements in Inches for 4:3

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
61”| 85.6| 48.8| 36.6| 3.6| 5.9| 8.0| 15.6
65”| 88.5| 52.0| 39.0| 4.8| 7.1| 8.5| 16.1
70″| 92.1| 56.0| 42.0| 6.3| 8.5| 9.1| 16.7
75″| 95.8| 60.0| 45.0| 7.7| 10.0| 9.8| 17.3
80″| 99.4| 64.0| 48.0| 9.2| 11.5| 10.4| 18.0
85”| 103.0| 68.0| 51.0| 10.6| 12.9| 11.0| 18.6
90”| 106.6| 72.0| 54.0| 12.1| 10.9| 11.6| 19.2
95”| 110.3| 76.0| 57.0| 13.5| 12.4| 12.2| 19.8
100”| 113.9| 80.0| 60.0| 15.0| 13.9| 12.9| 20.4
105”**| 117.5| 84.0| 63.0| 16.4| 15.3| 13.5| 21.1
110”**| 121.1| 88.0| 66.0| 17.9| 16.8| 14.1| 21.7
115”**| 124.8| 92.0| 69.0| 19.3| 18.2| 14.8| 22.3
120”****| 128.4| 96.0| 72.0| 20.8| 19.7| 15.4| 23.0

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 100”.
    Measurements in Centimeters for 4:3**

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
61”| 217.4| 124.0| 93.0| 9.2| 15.1| 20.3| 39.6
65”| 224.8| 132.1| 99.1| 12.2| 18.0| 21.6| 40.8
70 “| 234.0| 142.2| 106.7| 15.9| 21.7| 23.2| 42.4
75”| 243.2| 152.4| 114.3| 19.6| 25.4| 24.8| 44.0
80 “| 252.4| 162.6| 121.9| 23.3| 29.1| 26.4| 45.6
85”| 261.6| 172.7| 129.5| 27.0| 32.8| 28.0| 47.2
90”| 270.8| 182.9| 137.2| 30.7| 27.8| 29.5| 48.8
95”| 280.0| 193.0| 144.8| 34.4| 31.5| 31.1| 50.4
100”| 289.2| 203.2| 152.4| 38.0| 35.2| 32.7| 51.9
105”**| 298.4| 213.4| 160.0| 41.7| 38.9| 34.3| 53.5
110”**| 307.6| 223.5| 167.6| 45.4| 42.6| 35.9| 55.1
115”**| 316.9| 233.7| 175.3| 49.1| 46.3| 37.5| 56.7
120”****| 326.1| 243.8| 182.9| 52.8| 50.0| 39.1| 58.3

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 100”.

BrightLink EB-725Wi and PowerLite EB-725W
Measurements in Inches for 16:10

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
65”| 83.0| 55.1| 34.4| 2.7| 5.0| 7.6| 15.1
70″| 95.4| 59.3| 37.1| 3.9| 6.3| 17.3| 15.7
75″| 89.4| 63.6| 39.8| 5.2| 7.5| 8.7| 16.2
80″| 92.6| 67.8| 42.4| 6.4| 8.7| 9.2| 16.8
85″| 95.8| 72.1| 45.0| 7.6| 9.9| 9.8| 17.3
90″| 99.0| 76.3| 47.7| 8.8| 7.7| 10.3| 17.9
95”| 102.2| 80.6| 50.4| 10.0| 8.9| 10.9| 18.4
100”| 105.4| 84.8| 53.0| 11.2| 10.1| 11.4| 19.0
105”**| 108.6| 89.1| 55.7| 12.4| 11.3| 12.0| 19.5
110”**| 111.8| 93.3| 58.3| 13.7| 12.6| 12.5| 20.1
115”**| 115.0| 97.5| 60.9| 14.9| 13.8| 13.1| 20.6
120”****| 118.2| 101.7| 63.6| 16.1| 15.0| 13.6| 21.2

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 100”.
    Measurements in Centimeters for 16:10**

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
65”| 210.9| 140.0| 87.5| 6.9| 12.8| 19.2| 38.4
70 “| 219.0| 150.8| 94.2| 10.0| 15.9| 20.6| 39.8
75 “| 227.2| 161.6| 101.0| 13.1| 19.0| 22.0| 41.2
80 “| 235.3| 172.3| 107.7| 16.2| 22.0| 23.4| 42.6
85 “| 243.4| 183.0| 114.4| 19.2| 25.1| 24.8| 44.0
90 “| 251.6| 193.9| 121.2| 22.3| 19.5| 26.2| 45.4
95”| 259.7| 204.6| 127.9| 25.4| 22.6| 27.6| 46.8
100”| 267.8| 215.4| 134.6| 28.5| 25.7| 29.0| 48.2
105”**| 276.0| 226.2| 141.4| 31.6| 28.8| 30.4| 49.6
110”**| 284.1| 237.0| 148.1| 34.7| 31.9| 31.8| 51.0
115”**| 292.2| 247.7| 154.8| 37.8| 35.0| 33.2| 52.4
120”****| 300.3| 258.4| 161.5| 40.9| 38.1| 34.6| 53.8

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 100”.

BrightLink EB-725Wi and PowerLite EB-725W
Measurements in Inches for 16:9

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
65”| 82.4| 56.6| 31.9| 3.1| 5.5| 9.5| 17.1
70″| 85.6| 61.0| 34.3| 4.4| 6.7| 10.2| 17.8
75″| 88.7| 65.4| 36.8| 5.7| 8.0| 10.9| 18.5
80″| 91.9| 69.7| 39.2| 6.9| 9.2| 11.7| 19.2
85″| 95.0| 74.1| 41.7| 8.1| 10.5| 12.4| 19.9
90″| 98.2| 78.4| 44.1| 9.4| 8.3| 13.0| 20.6
95”| 101.3| 82.8| 46.6| 10.7| 9.5| 13.7| 21.3
100”| 104.5| 87.2| 49.0| 11.9| 10.8| 14.4| 22.0
105”**| 107.7| 91.5| 51.5| 13.1| 12.0| 15.2| 22.7
110”**| 110.8| 95.9| 53.9| 14.4| 13.3| 15.9| 23.4
115”****| 114.0| 100.2| 56.4| 15.7| 14.5| 16.6| 24.1

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Interactive features not supported for images larger than 100”.
    Measurements in Centimeters for 16:9**

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
65”| 209.3| 143.9| 80.9| 8.0| 13.9| 24.2| 43.4
70 “| 217.4| 155.0| 87.2| 11.2| 17.1| 26.0| 45.2
75 “| 225.4| 166.0| 93.4| 14.4| 20.2| 27.8| 47.0
80 “| 233.4| 177.1| 99.6| 17.5| 23.4| 29.6| 48.8
85 “| 241.4| 188.2| 105.8| 20.7| 26.6| 31.4| 50.6
90 “| 249.4| 199.2| 112.1| 23.9| 21.1| 33.1| 52.4
95”| 257.4| 210.3| 118.3| 27.1| 24.2| 34.9| 54.1
100”| 265.4| 221.4| 124.5| 30.2| 27.4| 36.7| 55.9
105”**| 273.5| 232.5| 130.8| 33.4| 30.6| 38.5| 57.7
110”**| 281.5| 243.6| 137.0| 36.6| 33.8| 40.3| 59.5
115”****| 289.5| 254.6| 143.2| 39.8| 36.9| 42.1| 61.3

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    **Interactive features not supported for images larger than 100”.

BrightLink EB-725Wi and PowerLite EB-725W
Measurements in Inches for 4:3

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
60”| 84.9| 48.0| 36.0| 3.4| 5.7| 7.9| 15.4
65”| 88.5| 52.0| 39.0| 4.8| 7.1| 8.5| 16.1
70″| 92.1| 56.0| 42.0| 6.2| 8.5| 9.1| 16.7
75″| 95.8| 60.0| 45.0| 7.6| 9.9| 9.8| 17.3
80″| 99.4| 64.0| 48.0| 8.9| 11.3| 10.4| 18.0
85”| 103.0| 68.0| 51.0| 10.3| 12.6| 11.0| 18.6
90”| 106.6| 72.0| 54.0| 11.7| 10.6| 11.6| 19.2
95”| 110.3| 76.0| 57.0| 13.1| 12.0| 12.2| 19.8
100”| 113.9| 80.0| 60.0| 14.4| 13.3| 12.9| 20.4
105”**| 117.5| 84.0| 63.0| 15.8| 14.7| 13.5| 21.1

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Measurements in Centimeters for 4:3

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
60”| 215.6| 121.9| 91.4| 8.7| 14.6| 20.0| 39.2
65”| 224.9| 132.1| 99.1| 12.2| 18.1| 21.6| 40.8
70 “| 234.1| 142.2| 106.7| 15.7| 21.6| 23.2| 42.4
75 “| 243.3| 152.4| 114.3| 19.2| 25.1| 24.8| 44.0
80 “| 252.5| 162.6| 121.9| 22.7| 28.6| 26.4| 45.6
85”| 261.7| 172.7| 129.5| 26.2| 32.1| 28.0| 47.2
90”| 270.9| 182.9| 137.2| 29.7| 26.9| 29.5| 48.8
95”| 280.1| 193.1| 144.8| 33.2| 30.4| 31.1| 50.4
100”| 289.3| 203.2| 152.4| 36.7| 33.9| 32.7| 51.9
105”**| 298.5| 213.3| 160.0| 40.2| 37.4| 34.3| 53.5

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

PowerLite EB-720
Measurements in Inches for 4:3

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
65”| 87.1| 52.0| 39.0| 4.0| 5.9| 7.0| 14.6
70″| 90.6| 56.0| 42.0| 5.3| 7.6| 7.6| 15.1
75″| 94.1| 60.0| 45.0| 6.6| 8.9| 8.1| 15.6
80″| 97.6| 64.0| 48.0| 7.9| 10.2| 8.6| 16.1
85”| 101.1| 68.0| 51.0| 9.2| 11.5| 9.1| 16.7
90”| 104.6| 72.0| 54.0| 10.5| 9.4| 9.6| 17.2
95”| 108.1| 76.0| 57.0| 11.8| 10.7| 10.1| 17.7
100”| 111.6| 80.0| 60.0| 13.1| 12.0| 10.6| 18.2
105”| 115.1| 84.0| 63.0| 14.4| 13.3| 11.1| 18.7
110”**| 118.6| 88.0| 66.0| 15.7| 14.6| 11.7| 19.2

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Measurements in Centimeters for 4:3

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
65”| 221.2| 132.1| 99.1| 10.1| 15.0| 17.9| 37.1
70 “| 230.1| 142.2| 106.7| 13.4| 19.3| 19.2| 38.4
75 “| 239.0| 152.4| 114.3| 16.7| 22.6| 20.5| 39.7
80 “| 247.9| 162.6| 121.9| 20.0| 25.9| 21.8| 41.0
85”| 256.8| 172.7| 129.5| 23.3| 29.2| 23.1| 42.3
90”| 265.8| 182.9| 137.2| 26.7| 23.8| 24.4| 43.6
95”| 274.7| 193.1| 144.8| 30.0| 27.2| 25.7| 44.9
100”| 283.6| 203.2| 152.4| 33.3| 30.5| 27.0| 46.2
105”| 292.5| 213.3| 160.0| 36.6| 33.8| 28.3| 47.5
110”**| 301.4| 223.5| 167.6| 39.9| 37.1| 29.6| 48.8

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

PowerLite EB-720
Measurements in Inches for 16:9

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
60”| 82.4| 52.3| 29.4| 4.1| 6.4| 12.0| 19.6
65”| 85.8| 56.6| 21.9| 5.5| 7.8| 13.0| 20.5
70″| 89.2| 61.0| 34.3| 6.9| 9.2| 13.9| 21.5
75″| 92.7| 65.4| 36.8| 8.3| 10.6| 14.9| 22.4
80″| 96.1| 69.7| 39.2| 9.8| 12.1| 15.9| 23.4
85″| 99.5| 74.1| 41.7| 11.2| 13.5| 16.8| 24.4
90″| 102.9| 78.4| 44.1| 12.6| 11.5| 17.8| 25.4
95”| 106.3| 82.8| 46.6| 14.0| 12.9| 18.7| 26.3
100”**| 109.7| 87.2| 49.0| 15.4| 14.3| 19.7| 27.3

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Measurements in Centimeters for 16:9

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
60”| 209.3| 132.8| 74.7| 10.3| 16.2| 30.4| 49.7
65”| 218.0| 143.8| 80.9| 13.9| 19.8| 32.9| 52.1
70 “| 226.7| 155.0| 87.2| 17.6| 23.4| 35.3| 54.6
75 “| 235.4| 166.0| 93.4| 21.2| 27.0| 37.8| 57.0
80 “| 244.1| 177.1| 99.6| 24.8| 30.7| 40.3| 59.5
85 “| 252.7| 188.2| 105.8| 28.4| 34.3| 42.7| 61.9
90 “| 261.5| 199.2| 112.1| 32.0| 29.2| 45.2| 64.4
95”| 270.1| 210.3| 118.3| 35.6| 32.8| 47.6| 66.8
100”**| 278.8| 221.4| 124.5| 39.2| 36.4| 50.1| 69.3

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

PowerLite EB-720
Measurements in Inches for 16:10

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
60”| 82.9| 50.8| 31.8| 3.6| 5.9| 10.1| 17.6
65”| 86.3| 55.1| 34.4| 5.0| 7.3| 10.9| 18.5
70″| 89.8| 59.3| 37.1| 6.4| 8.7| 11.7| 19.3
75″| 93.3| 63.6| 39.8| 7.8| 10.1| 12.5| 20.1
80″| 96.7| 67.8| 42.4| 9.1| 11.5| 13.3| 20.9
85″| 100.2| 72.1| 45.0| 10.5| 12.8| 14.1| 21.7
90″| 103.6| 76.3| 47.7| 11.9| 10.8| 14.9| 22.5
95”| 107.1| 80.6| 50.4| 13.3| 12.2| 15.7| 23.3
100”**| 110.5| 84.8| 53.0| 14.7| 13.5| 16.5| 24.1

  • Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
    Measurements in Centimeters for 16:10

Diagonal image size (S)| Min. ceiling **height*| Image width (w)| Image height (h)| Min. projection distance (a)| Sliderscale mark (b)| Distance from top of image to bottom wall plate holes (c)| Distance from top of image to temporary wall plate hole (d)
---|---|---|---|---|---|---|---
60”| 210.6| 129.3| 80.8| 9.2| 15.0| 25.6| 44.8
65”| 219.3| 140.0| 87.5| 12.7| 18.6| 27.6| 46.9
70 “| 228.1| 150.7| 94.2| 16.2| 22.1| 29.7| 48.9
75 “| 237.0| 161.6| 101.0| 19.7| 25.6| 31.8| 51.0
80 “| 245.7| 172.3| 107.7| 23.2| 29.1| 33.8| 53.0
85 “| 254.5| 183.0| 114.4| 26.7| 32.6| 35.9| 55.1
90 “| 263.3| 193.9| 121.2| 30.2| 27.4| 37.9| 57.1
95”| 272.1| 204.6| 127.9| 33.7| 30.9| 40.0| 59.2
100”**| 280.8| 215.4| 134.6| 37.3| 34.4| 42.0| 61.2

  • Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

Installing the Projector

Make sure to follow the steps below to install the wall mount. If you ignore these steps, the wall mount could fall and cause personal injury or property damage.

Warning
❏ When you mount the projector on the wall with the wall mount, the wall requires enough strength to hold the projector and the wall mount, as well as the Control Pad and the Touch Unit, if applicable.
This wall mount should be installed on a concrete wall. Confirm the weight of the projector and the wall mount before installation, and maintain the strength of the wall. If the wall is not strong enough, reinforce the wall before installation.
❏ The maximum combined weight of the projector and the wall mount is about 41.7 lb (18.9 kg).
❏ Do not hang cables over the wall mount.
❏ Install the wall mount so that it can sufficiently support the weight of the projector and wall mount, and resist any horizontal vibration. Use M10 or 3/8 inch nuts and bolts and make sure to use appropriate wall anchors for your wall type. Nuts and bolts smaller than M10 or 3/8 inch could cause the wall mount to fall.
❏ Epson accepts no responsibility for any damage or injury caused by lack of wall strength or inadequate installation.

Assemble the parts

  1. Assemble the wall plate.
    Assemble the wall plate and two frames into one unit, and secure them with the M4 × 12 mm hexagon socket head cap bolts (×5) supplied.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - dimensions 9

  2. BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F only: Loosen the two screws with a cross-head screwdriver and remove the cable cover from the projector.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - dimensions 10

  3. Align the 3-axis adjustment unit with the slide plate’s alignment mark.
    If the 3-axis adjustment unit is not aligned, loosen the M4 × 12 mm hexagon socket head cap bolt (1) and correct the alignment (2). Then, tighten the M4 × 12 mm hexagon socket head cap bolt.

  4. Attach the 3-axis adjustment unit and slide plate to the projector.
    Attach the 3-axis adjustment unit and slide plate to the projector using the M4 × 12 mm hexagon socket head cap bolts (×4) supplied.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - dimensions 12

Install the wall plate on the wall

  1. Determine the template sheet position and attach it to the wall.
    • Confirm where the beams or studs are within the wall that can support the projector and wall mount.
    • From the projection distance table, confirm the screen size (S), the distance between the projection image and wall plate bottom holes (c), and the distance between the projection image and temporary wall plate hole (d).
    • BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F: Align the center of the projection surface (vertical) with Image Center A (vertical) on the template sheet.
    BrightLink EB-725Wi/EB-735Fi/EB-760Fi/EB-770Fi and PowerLite EB-720/EB-725W /EB-750F/EB-755F/EB-760W/EB-770F/EB-775F: Align the center of the projection surface (vertical) with Image Center B (vertical) on the template sheet.
    • Align the lines (horizontal) on the template with the height of (c) and (d).Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 5 If you want to hide the projector power plug under the wall plate cover, make sure the power outlet is located in the empty space to the left or the right of the wall plate.

  2. Drive an M10 screw (not included) into the temporary wall plate hole.
    Leave at least 0.2 inch (6 mm) between the screw head and the wall.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 6

  3. Determine the position of the wall plate’s mounting holes.
    Use at least four mounting holes at the top, bottom, left, and right for proper balance.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 7

  4. Drill holes of the following diameters and depths.
    Drill diameter| 3/8 inch anchor bolts: 0.39 in. (10 mm) M10 anchor bolts: 0.41 in. (10.5 mm)
    ---|---
    Pilot hole depth| 1.8 in. (45 mm)
    Anchor hole depth| 1.6 in. (40 mm)

When routing cables to the projector through a wall, you can drill routing holes within the areas shown below. When installing a mini-PC, check the position at which the mini-PC plate will be installed before drilling the cable routing holes.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 9

  1. Remove the template sheet.
  2. If necessary, use a device such as a dust pump to clean out concrete dust from the hole.
  3. Position the wall plate on the temporary wall plate screw.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 11
  4. Insert commercially available M10 × 60 mm or 3/8 inch anchors into the holes and secure them in place.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 12
  5. Remove the temporary wall plate screw.

Determine the projection distance and pull out the mount arm slider

  1. Using the tables on pages 29 to 51, check the number for the slider measure (b).
  2. Loosen the M4 × 12 mm hexagon socket head cap bolts (×2), and then pull out the slider on the wall mount.
    Align the slider with the measure (b+x) that is equal to the slider measure (b) plus the thickness of the projection screen (x).

The measurement for (b+x) should not exceed 20.98 inches (533 mm). If you are using the touch unit bracket, (x) should be between 0.59 to 2 inches (15 to 50 mm).
For an illustration of how to measure the thickness of the projection screen (x), see page 27.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Route the cables through the wall mount arm

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

For BrightLink projectors with a Touch Unit: Make sure to route the Touch Unit connection cable through the wall mount arm. Route the Touch Unit connection cable so that the end that connects to the Touch Unit appears from the lower part of the wall mount as shown above.

Attach the mount arm to the wall plate

  1. Insert the hexagonal shaft into the wall mount (1).

  2. Insert and turn the hexagonal shaft at the top of the mount arm into the slot on the wall plate (2).Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 15

  3. Insert the hexagonal shaft into the slot at the top of the wall plate (1).

  4. Insert the hexagonal shaft into the slot at the bottom of the wall plate (2).
    Caution
    ❏ Make sure the Touch Unit connection cable is not wired into the wall with the other cables.
    ❏ Take care not to trap the cables between the mount arm and wall plate.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 16

  5. Secure the mount arm to the wall plate by tightening the supplied M6 × 20 mm cross recessed head shoulder screws (×3) with the #3 cross-head screwdriver.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 17

Make sure you use the included plastic washers. If you don’t use the plastic washers, you may damage the M8 hexagon bolt as you adjust the vertical slide position.

Adjust the vertical slide position of the arm

  1. Adjust the vertical slide with the M8 hexagon bolt at the bottom of the wall mount (2), or the hexagonal shaft at the top of the wall mount (1). Start by aligning the notch on the arm with the alignment mark on the wall plate as shown below (3).
    Tightening the M8 hexagon bolt lowers the wall mount, and loosening the bolt raises it (2).
    Tightening the hexagonal shaft raises the wall mount, and loosening the shaft lowers it (1).Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 18

  2. Secure the wall mount with the M6 × 20 mm hexagon shoulder bolt.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 19

Attach the projector to the wall mount
Attach the 3-axis adjustment unit with the projector to the wall mount arm.
Decide which position you want to use for installing the 3-axis adjustment unit:

  • BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F: Mount it at the stamp when the image is less than 80 inches diagonally, or at the stamp when the projected image is 80 inches or more diagonally.
  • BrightLink EB-725Wi/EB-735Fi/EB-760Wi/EB-770Fi and PowerLite EB-720/EB-725W/EB-750F/EB-755F/EB-760W/EB-770F/EB-775F: Mount it at the stamp when the image is less than 90 inches diagonally, or at the stamp when the projected image is 90 inches or more diagonally.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Warning
When installing or adjusting the wall mount, do not use adhesives to prevent the screws from loosening and do not use lubricants or oils on the projector slide plate. This may cause the case to crack and the projector to fall, resulting in personal injury or property damage.

Connect the power cord and other cables to the projector
Connect any necessary cables such as the computer cable, HDMI cable, USB cable, Touch Unit connection cable (if applicable), Control Pad cables (if applicable), and power cord to the projector. See your projector’s online User Guide for detailed connection information.
Use M4 screws (not included) to secure any additional devices or accessories, such as external tuners, to the mounting point on the wall mount.

If you are planning to run the cables inside the wall, make sure you follow all local electrical codes. If you are running the cables outside the wall, use a cable management system to keep the cables from obstructing the image. An optional cable management  system is available from Epson (part number ELPCK01).

Attach a Mini PC or Stick PC if necessary
You can secure a Mini PC or Stick PC to the left or the right side of the wall plate.
Attach the Mini PC so that the air exhaust vents of the PC are not blocked. Install the PC so that the air exhaust vents are at the top and the air intake vents are at the bottom.
If your Mini PC has screw holes that line up with the holes in the Mini PC plate, you can secure it with the M3 × 6 mm screws (×4) supplied.

If your Mini PC does not have screw holes or they do not line up with the holes on the Mini PC plate, you can secure it with the included Mini PC band.

  1. Wrap the band around the Mini PC plate.
  2. Secure the Mini PC plate to the wall plate using the M3 × 6 mm screws (×4) supplied.
  3. Rest the PC on the lip of the Mini PC plate and secure it with the band.

Adjusting the Image

To ensure the best image quality, follow the steps below to adjust the projected image. You can also use the Auto Screen Adjustment feature to automatically adjust the image. See page 111 for more information.
For information on adjusting the shared image of two or more projectors, see the online Edge Blending Setup Guide for your product.

If possible, avoid adjustments with the Auto Screen Adjustment, Quick Corner, or Keystone functions of the projector. Doing so may result in a reduction in image quality and pen or finger touch calibration.

Follow these guidelines for setting up the projector:

  • Make sure the image is evenly rectangular, without distortion.
  • Make sure the projector is tilted no more than 3° vertically and horizontally in relation to the projected image.

Your remote control or projector control panel may look different from the illustrations in this section, but the instructions are the same except where noted.

Turn on the projector
Press the power button on the remote control or the projector.

Adjust the focus

  1. Open the cover (1).

  2. Use the focus lever to adjust the focus (2).
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 27BrightLink EB-725Wi/EB-735Fi /EB-760Wi/EB-770Fi and PowerLite EB-720/EB-725W/EB-750F/EB-755F/EB-760W/EB-770F/EB-775F:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 28

  3. After you finish making the adjustment, close the cover.

Select the screen type

  1. Press the [Menu] button on the remote control or control panel.
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 29BrightLink EB-725Wi/EB-735Fi/EB-760Wi/EB-770Fi and PowerLite EB-720 /EB-725W/EB-750F/EB755F/EB-760W/EB-770F/EB-775F:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 30

  2. Select Installation.

  3. Select Screen Type.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 31

  4. Select the setting that matches the aspect ratio of your projection surface.
    If necessary, you can press the [Aspect] button on the remote control to temporarily change the aspect ratio as necessary to match the input signal.
    You will need to project content from a connected device in order to change the aspect ratio.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 32The following is a list of available aspect settings:
    • Auto: Automatically sets the aspect ratio according to the input signal and the Resolution setting.
    • Full: Displays images using the full width of the projection area, but does not retain the aspect ratio.
    4:3 ratio images are elongated horizontally.
    • Zoom: Displays images using the full width of the projection area and maintains the aspect ratio of
    the image. The image may be cut off on the top and bottom depending on its aspect ratio.
    • Native: Displays images as is (aspect ratio and resolution are maintained). Black bands may appear or images may be cut off, depending on the resolution.

  5. If you selected the 16:6 (BrightLink 1485Fi/1485Fi+/EB-735Fi/EB-770Fi and PowerLite EB-750F/EB-755F/ EB-770F/EB-775F/EB-800F/EB-805F only) or 21:9 (BrightLink 1480Fi/14840Fi+/1485Fi/1485Fi+/EB-770Fi and PowerLite EB-770F/EB-775F/EB-800F/EB-805F) Screen Type setting and want to eliminate the black bar at the top of the screen, select the Installation > Screen Position setting and then press and hold the up arrow button on the remote until the image rests at the top of the screen.

Display the test pattern

  1. Press the [Menu] button on the remote control or control panel.
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 33BrightLink EB-725Wi/EB-735Fi/EB-760Wi/EB-770Fi and PowerLite EB-720 /EB-725W/EB-750F/EB755F/EB-760W/EB-770F/EB-775F:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 34

  2. Select Installation.

  3. Select Setting Plate Installation Guide.

  4. The installation guide and test pattern are displayed. Use these to monitor the image as you make the adjustments in steps 5 to 10.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 35

Use adjustment dial 1 on the left side to adjust the horizontal roll

Repeat steps 5 to 10 as necessary.

  1. Loosen the lower adjustment dial (1).Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 36
  2. Turn the upper adjustment dial to adjust the horizontal roll (2).
  3. After you finish making all of the adjustments in steps 5 to 10, tighten the lower adjustment dial you loosened in 1.

Use adjustment dial 2 on the top to adjust the horizontal rotation

  1. Loosen the screw to unlock the adjustment dials (1).Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 37
  2. Turn the adjustment dials to adjust the horizontal rotation (2).
  3. After you finish making all of the adjustments in steps 5 to 10, tighten the screw you loosened in 1.

Use adjustment dial 3 on the front to adjust the vertical tilt

  1. Loosen the lower adjustment dial (1).Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 38
  2. Turn the upper adjustment dial to adjust the vertical tilt (2).
  3. After you finish making all of the adjustments in steps 5 to 10, tighten the lower adjustment dial you loosened in 1.

Adjust the horizontal slide

  1. Loosen the M4 × 12 mm hexagon socket head cap bolt (1).
  2. Adjust the slider for the slide plate (2).Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 39
  3. After you finish making all of the adjustments in steps 5 to 10, tighten the M4 × 12 mm hexagon socket head cap bolt you loosened in 1.

Adjust the forward/backward slide

  1. Loosen the M4 × 12 mm hexagon socket head cap bolts (×2) (1).
  2. Adjust the slider for the wall mount (2).Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 40
  3. After you finish making all of the adjustments in steps 5 to 10, tighten the M4 × 12 mm hexagon socket head cap bolts (×2) you loosened in 1.

Adjust the vertical slide

  1. Loosen the M6 × 20 mm hexagon shoulder bolt (1).

  2. Adjust the vertical slide with the M8 hexagon bolt at the bottom of the wall mount, or the hexagonal shaft at the top of the wall mount (2).
    Tightening the M8 hexagon bolt lowers the wall mount, and loosening the bolt raises it.
    Tightening the hexagonal shaft raises the wall mount, and loosening the shaft lowers it.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 41

  3. After you finish making your adjustments, tighten the M6 × 20 mm hexagon shoulder bolt you loosened in 1.

Re-adjust the focus

  1. Open the front cover (1).

  2. Use the focus lever to adjust the focus (2).
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 42BrightLink EB-725Wi/EB-735Fi/EB-760Wi/EB-770Fi and PowerLite EB-720 /EB-725W/EB-750F/EB755F/EB-760W/EB-770F/EB-775F:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 43

  3. After you finish making the adjustment, close the cover.

Turn off the display of the test pattern
Press the [Esc] button on the remote control or control panel to turn off the test pattern.

Warning
Tighten all screws firmly. Otherwise, the projector or wall mount may fall and cause personal injury or property damage.

Attaching the Covers

Attach the wall plate cover and end cap
If you need to use a security cable, make sure you attach it before installing the wall plate cover. See page 119 for instructions.

  1. Attach the left wall plate cover.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 44
  2. Attach the right wall plater cover.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 45
  3. Attach the end cap to the mount arm.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 46
  4. If you want to cover the groove in the mount arm, attach the masking sticker as shown.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Attach the cable cover to the projector (BrightLink 1480Fi/1480Fi+/ 1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F only)
Attach the cable cover (1) and use a cross-head screwdriver to tighten the screws (x2) and secure the cable cover (2).

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Caution
Only a specialist should remove or reinstall the projector, including for maintenance and repairs. Refer to your online User’s Guide for your projector for instructions on maintenance and repairs.

Warning
❏ Never loosen the bolts and nuts after installation. If you find any loose screws, tighten them firmly. Otherwise, the projector or wall mount may fall and cause personal injury or property damage.
❏ Do not hang on the wall mount or hang a heavy object on the wall mount. If the projector or wall mount falls, it could cause personal injury or property damage.

Installing the Touch Unit

Before installing the touch unit, make sure you install the projector and adjust the projected image (see page 52). You also need to calibrate the interactive pen(s) before you install the touch unit (see the online User’s Guide for more information).

The touch unit is included with the BrightLink 1485Fi/1485Fi+. You can purchase it as an optional accessory for the BrightLink 1480Fi/1480Fi+/EB- 725Wi/EB-735Fi/ EB-760Wi/EB-770Fi.

The steps for installing the touch unit vary depending on where you are installing the touch unit:

  • If you are installing the touch unit on a whiteboard, see ”Installing the touch unit on a whiteboard” on page 77.
  • If you are installing the touch unit above the frame of a whiteboard (requires the optional touch unit bracket), see ”Installing the touch unit above a whiteboard” on page 89. To achieve the best touch performance it is highly recommended that you install the touch unit directly on the whiteboard.

❏ If the distance from the wall to the surface of the whiteboard is greater than 2 inches (51 mm), you must install the touch unit on the whiteboard.
❏ If the frame of the whiteboard extends more than 0.1 inch (3 mm) away from the board surface, you must install the touch unit on the whiteboard.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Caution
The touch unit should only be connected to the BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+/ EB-725Wi/EB-735Fi/EB-760Wi/EB-770Fi models. Do not connect the touch unit to any other projectors or devices.

Installing the touch unit on a whiteboard
Follow the steps below to install the touch unit on a whiteboard. Some menus may differ slightly from theillustrations, but the installation instructions are the same.

❏ There are magnets built in to the back of the touch unit. Typically, the touch unit should be installed by attaching the magnets to the screen or whiteboard.
❏ If the touch unit cannot be attached with the magnets, use commercially available M4 screws (×2).
❏ Install the touch unit on a flat, smooth, unwarped surface. If there is unevenness on the screen surface of more than 0.2 inch (5 mm) in any direction, your fingers may not be detected and finger touch operations may not be performed correctly.

Install infrared deflectors along any obstacles
If there is an obstacle that cannot be removed, such as a whiteboard tray or thick frame, remove the tape from the back of the supplied infrared deflectors and stick them to the screen so that the laser is not reflected by the obstacle.
Make sure to use as many deflectors as necessary to match the full width of the obstacle.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

❏ Do not remove an infrared deflector once it has been stuck in place.
❏ Do not stick tape on or place anything on the infrared deflectors. The deflectors will not function properly if anything is placed on them.

Turn on the projector
Press the power button on the remote control or the projector.
Display the installation pattern

  1. Press the [Menu] button on the remote control or control panel.
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 51BrightLink EB-725Wi/EB-735Fi/EB-760Wi /EB-770Fi:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 52

  2. Select Installation.

  3. Select Touch Unit.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 53

  4. Select Installation Pattern.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

The Installation pattern is displayed on the projected image.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Determine the installation position for the touch unit

  1. Mark the following installation positions:
    • (1): The center line of the installation pattern.
    • (2): The distance from the top edge of the projected image to the bottom edge of the touch unit.
    BrightLink 1480/1480Fi+/1485Fi/1485Fi+/EB-725Wi/EB-735Fi: 0.79 to 1.97 inches (20 to 50 mm) for 16:6/21:9 aspect ratio images or 0.22 to 1.97 inches (5.7 to 50 mm) for all others.
    BrightLink EB-770Fi: 1.83 to 2 inches (46.4 to 50 mm) for 16:6 aspect ratio images, 1.5 to 2 inches (38.1 to 50 mm) for 21:9 aspect ratio images, or 0.76 to 2 inches (19.2 to 50 mm) for all others.
    BrightLink EB-760Wi: 0.65 to 2 inches (16.4 to 50 mm) for all aspect ratio images.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 56 The touch unit must be installed above the image area.

  2. For non-magnetic boards or screens, attach the template sheet to the board.
    Line up the pattern on the bottom of the sheet with the top of the projected pattern.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Drill two holes where indicated and remove the template sheet.

Install the touch unit

  • For magnetic boards, place the back of the touch unit on the screen surface to secure it.

Caution
When installing the touch unit on a magnetic surface, be careful not to trap your fingers or any other part of your body between the magnets and the installation surface.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Remove the rubber caps from the front of the touch unit.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Secure the touch unit with two (2) M4 screws (not included).

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Re-attach the rubber caps.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Turn on the touch unit

  1. Connect the touch unit connection cable from the projector to the port on the touch unit. Make sure the arrows on the port and cable are lined up.
    Make sure you use the supplied touch unit connection cable. Operations are not possible with a commercially available cable.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 63 Make sure the touch unit connection cable is firmly inserted all the way in. if the cable is not inserted all the way in, the menu for the older model Touch Unit may be displayed when adjusting the angle of the laser.

  2. Press the [Menu] button on the remote control or control panel.
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 64 BrightLink EB-725Wi/EB-735Fi/EB-760Wi /EB-770Fi:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 65

  3. Select Installation.

  4. Select Touch Unit.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 66

  5. Set Power to On.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 67

The touch unit power turns on and the power light turns blue.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Warning
Do not look into the projector’s projection window or the touch unit’s laser diffusion ports (located on the bottom of the touch unit); this could cause injury to eyesight.
When Power is set to On, the touch unit automatically powers up when the projector is turned on.

Adjust the angle
Adjust the angle of the laser light coming from the touch unit so that the touch unit can detect the position of your fingers.

Make sure to calibrate the interactive pen(s) before running touch unit setup. Press the User button on the remote control and select Yes to perform an auto- calibration. Refer to the online User’s Guide for your projector for detailed instructions on calibrating the pen(s).

  1. Press the [Menu] button on the remote control or control panel.
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 69BrightLink EB-725Wi/EB-735Fi/EB-760Wi /EB-770Fi:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 70

  2. Select Installation.

  3. Select Touch Unit.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 71

  4. Select Touch Unit Setup (Auto).Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 72 If you’re using multiple projectors and the HDMI Out Setting option in the MultiProjection menu is set to Process Out, follow the on-screen instructions to turn off the Power setting for the touch unit on the next projector you set up.

  5. Select Installing the Touch Unit without the bracket.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 73 If the screen for an older model Touch Unit is displayed even though the ELPFT01 is connected, check the connection for the touch unit connection cable.

  6. Attach the two markers to the positions shown on the projected screen.
    Match the positions so that the crosses (1) overlap with the points (2) on the marker positions.
    Move the marker over the projected cross until the lines of the cross align with the lines on the marker.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 74Attach the markers to the projection screen as follows:
    • For magnetic screens: Place the bottom of the markers onto the screen with the thinner end of the marker facing the touch unit.
    • For non-magnetic screens: Use the supplied tape to secure the markers with the thinner side of themarker facing the touch unit.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 75 Do not place anything other than the markers near the projected image during angle adjustment. If other objects are on the projected image, angle adjustment may not be performed correctly.

  7. Press the [Enter] button on the remote control or control panel to begin the auto adjustment.

  8. When adjustments are complete, remove the markers.
    If auto adjustment fails, follow the instructions on the screen to manually adjust the angle of the laser and run auto adjustment again. If the problem continues to occur even after checking all of the items, run Touch Unit Setup (Manual). For details on manual adjustment, see page 101. If the problem continues to occur, the Touch Unit may be malfunctioning. Contact your dealer.

  9. Touch each of the four yellow circles on the screen and verify that the gray touch indicators appear in the correct position.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 76 Finger touch operations may not function correctly if you are wearing bandages, artificial nails, nail polish, or anything else that may obstruct your fingers.
    If the gray indicators do not appear where you touched the screen, you need to manually adjust the touch unit alignment.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 77Select Up using the control panel or remote control and press [Enter]. Try touching the four dots again and repeat this process until the touch indicators appear in the correct position.

  10. Perform touch calibration by pressing Menu on the remote control. On the Installation menu, select Touch Unit, then Touch Calibration. Follow the instructions on the screen.

See the online User’s Guide for more details on the touch calibration.

Attach labels
Attach the labels to the tabs on either side of the touch unit.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

If the touch unit moves out of position, use the labels to determine where to reposition the touch unit.

Installing the touch unit above a whiteboard
Follow the steps below to use the optional touch unit bracket to install the touch unit above the frame of a whiteboard. Some menus may differ slightly from the illustrations, but the installation instructions are the same.

Install the touch unit bracket on a flat, smooth, unwarped surface. If there is unevenness on the screen surface of more than 0.2 inch (5 mm) in any direction, your fingers may not be detected and finger touch operations may not be performed correctly.

Install infrared deflectors along any obstacles
If there is an obstacle that cannot be removed, such as a whiteboard tray or thick frame, remove the tape from the back of the supplied infrared deflectors and stick them to the screen so that the laser is not reflected by the obstacle.
Make sure to use as many deflectors as necessary to match the full width of the obstacle.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

❏ Do not remove an infrared deflector once it has been stuck in place.
❏ Do not stick tape on or place anything on the infrared deflectors. The deflectors will not function properly if anything is placed on them.

Turn on the projector
Press the power button on the remote control or the projector.
Display the installation pattern

  1. Press the [Menu] button on the remote control or control panel.
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 80BrightLink EB-725Wi/EB-735Fi/EB-760Wi /EB-770Fi:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 81

  2. Select Installation.

  3. Select Touch Unit.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 82

  4. Select Installation Pattern.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 83

The Installation pattern is displayed on the projected image.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Determine the installation position for the bracket
Align the bottom of the bracket template sheet with the top of the projection surface and attach the sheet to the wall.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

The touch unit must be installed above the image area.

Drill holes for the bracket
If possible, drill holes at the four points labeled Main on the template sheet.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

If you’re unable to use the points labeled Main, you can secure the bracket at the points labeled Sub.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Make sure you secure the bracket at four points (two on the left and two on the right) for proper balance.

Install the bracket

  1. Loosen the screws (×2) at the top of the bracket.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 88

  2. Slide the front of the bracket forward until it is fully extended.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 89To prevent the front of the bracket from slipping during installation, loosely tighten the top screws.

  3. Secure the bracket on the wall using four (×4) 3.8 mm wood screws that are 46 mm long or four (×4) M4 anchor bolts (not included).Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 90

  4. Slide the front of the bracket until the lower edge touches the projection surface.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 91 ❏ If the distance from the wall to the surface of the whiteboard is greater than 2 inches (51 mm), you must install the touch unit on the whiteboard.
    ❏ If the frame of the whiteboard extends more than 0.1 inch (3 mm) away from the board surface, you must install the touch unit on the whiteboard.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 92

  5. Tighten the screws (×2) at the top of the bracket that you loosened in step 1.

  6. Remove the rubber caps (×2) from the front of the touch unit.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 93

  7. Secure the touch unit to the bracket with the M4× 25 mm bolts (×2) supplied.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 94 Caution
    When attaching the touch unit to the bracket, be careful not to trap your fingers or any other part of your body between the magnets and the bracket.

  8. Re-attach the rubber caps.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Turn on the touch unit

  1. Connect the touch unit connection cable that is connected to the projector to the port on the Touch Unit.
    Make sure you use the supplied touch unit connection cable. Operations are not possible with a commercially available cable.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 96

  2. Press the [Menu] button on the remote control or control panel.
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 97BrightLink EB-725Wi/EB-735Fi/EB-760Wi /EB-770Fi:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 98

  3. Select Installation.

  4. Select Touch Unit.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 99

  5. Set Power to On.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

The touch unit power turns on and the indicator light turns blue.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Warning
Do not look into the projector’s projection window or the touch unit’s laser diffusion ports (located on the bottom of the touch unit); this could cause injury to eyesight.
When Power is set to On, the touch unit automatically powers up the next time the projector is turned on.

Adjust the angle
Adjust the angle of the laser light coming from the touch unit so that the touch unit can detect the position of your fingers.

Make sure to calibrate the interactive pen(s) before running touch unit setup. Press the User button on the remote control and select Yes to perform an auto- calibration. Refer to the online User’s Guide for your projector for detailed instructions on calibrating the pen(s).

  1. Press the [Menu] button on the remote control or control panel.
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 102BrightLink EB-725Wi/EB-735Fi/EB-760Wi /EB-770Fi:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 103

  2. Select Installation.

  3. Select Touch Unit.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 104

  4. Select Touch Unit Setup (Auto).Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 105 If you’re using multiple projectors and the HDMI Out Setting option in the MultiProjection menu is set to Process Out, follow the on-screen instructions to turn off the Power setting for the touch unit on the next projector you set up.

  5. Select Installing the Touch Unit with the bracket.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 106 If the screen for an older model Touch Unit is displayed even though the ELPFT01 is connected, check the connection for the touch unit connection cable.

  6. Loosen the adjustment screw at the top of the bracket until it stops turning.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 107 Make sure you stop loosening the screw as soon as it stops turning. Continuing to turn the screw may remove it from the bracket.

  7. Attach the two markers to the positions shown on the projected screen.
    Match the positions so that the crosses (1) overlap with the points (2) on the marker positions.
    Move the marker over the projected cross until the lines of the cross align with the lines on the marker.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 108Attach the markers to the projection screen as follows:
    • For magnetic screens: Place the bottom of the markers onto the screen.
    • For non-magnetic screens: Use the supplied tape to secure the markers.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 109 Do not place anything other than the markers near the projected image during angle adjustment. If other objects are on the projected image, angle adjustment may not be performed correctly.

  8. Press the [Enter] button on the remote control or control panel to begin the auto adjustment.

  9. When adjustments are complete, remove the markers.
    If auto adjustment fails, follow the instructions on the screen to manually adjust the bracket position and run auto adjustment again. If the problem continues to occur even after checking all of the items, run Touch Unit Setup (Manual). For details on manual adjustment, see page 101. If the problem continues to occur, the Touch Unit may be malfunctioning. Contact your dealer.

  10. Touch each of the four yellow circles on the screen and verify that the gray touch indicators appear in the correct position.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 110 Finger touch operations may not function correctly if you are wearing bandages, artificial nails, nail polish, or anything else that may obstruct your fingers.
    If the gray indicators do not appear where you touched the screen, you need to manually adjust the touch unit alignment.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 111Select Up using the control panel or remote control and press [Enter]. Try touching the four dots again and repeat this process until the touch indicators appear in the correct position.

  11. Perform touch calibration by pressing Menu on the remote control. On the Installation menu, select Touch Unit, then Touch Calibration. Follow the instructions on the screen.
    See the online User’s Guide for more details on the touch calibration.

Manually adjusting the angle of the laser
If Touch Unit Setup (Auto) fails, you can make adjustments manually.

  1. Press the [Menu] button on the remote control or control panel.
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 112BrightLink EB-725Wi/EB-735Fi/EB-760Wi /EB-770Fi:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 113

  2. Select Installation.

  3. Select Touch Unit.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 114

  4. Select Touch Unit Setup (Manual).Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 115

  5. Select whether or not the Touch Unit bracket is being used.
    If you are not using the bracket, skip to step 9.

  6. If you are using the Touch Unit bracket, turn the adjustment screw at the top of the bracket clockwise until it stops turning.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 116

  7. Place the two supplied markers on the marker positions on the projected screen and secure them.
    When the markers have been secured, pointers appear on the left and right of the projected screen.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 117If the pointers do not appear, turn the adjustment screw on the top of the Touch Unit bracket until they do.

  8. Turn the adjustment screw on the top of the bracket to move the pointers into the targets.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 118When a pointer is moved into its target, the circle becomes solid. When both left and right pointers are in their targets and solid, press the [Enter] button on the remote control.

  9. Attach the two markers to the positions shown on the projected screen.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 119

  10. Press the number [4] button on the remote control until a pointer is displayed on the left of the projected screen.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 120

  11. Press the number [6] button on the remote control until a pointer is displayed on the right of the projected screen.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 121 If the pointer on the left moves off the screen while you are moving the pointer on the right, press the number [7] button on the remote control until it appears again.

  12. Use the number [4] and [6] buttons on the remote control to move the left and right pointers into their targets.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 122When the pointers are in their targets, the circles become solid. When both left and right pointers are in their targets and solid, press the [Enter] button on the remote control.
    ❏ When you move one pointer, the other pointer moves slightly. Adjust the left and right pointers by alternating their positions a little at a time.
    ❏ If the pointers move beyond the target positions, use the number [7] or [9] buttons on the remote control to move the pointers in the opposite direction.
    ❏ If you cannot move the pointers as intended, press the [Esc] button on the remote control and start over from step 9.

  13. Follow the on-screen instructions to place the markers on the marker positions and then check the adjustment results.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 123Check that the circles displayed on the projected screen are solid when the markers are placed on the marker positions.

  14. Remove the markers and then use your finger to trace the dots on the projected screen.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 124When all of the dots have disappeared, select Complete. If any of the dots do not disappear, select Additional Adjustment and follow the on-screen instructions.

  15. Test finger touch operation to see if it is functioning correctly. Otherwise, touch calibration may be required.

See the online User’s Guide for more details on the touch calibration.

Installing the HDBaseT Control Pad and Pen Stand

You must install the projector before installing the control pad and pen stand.
Caution
The control pad should only be connected to the BrightLink 1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F. Do not connect the control pad to any other projectors. Previous Epson control pad models do not support HDBaseT.
Check the installation location
Make sure there is enough space surrounding the control pad to easily connect or disconnect cables.
If you are using the touch unit, make sure that you do not install the control pad or pen stand in the shaded areas of the following figure. The touch unit will not operate correctly if anything is obstructing the infrared signal.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Installing the HDBaseT Control Pad
The Control Pad is included with the BrightLink 1485Fi/1485Fi+ and is an optional accessory for the PowerLite EB-800F/EB-805F.
Remove the front cover
Grip the hole in the top of the cover and remove it.

Connect the power cable
Connect the power cable and route it down the groove on the back of the control pad.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Attach the control pad
Attach the control pad with commercially available M4 × 20 mm screws (×4).

Warning
❏ Make sure the screws are not angled.
❏ Make sure the control pad is firmly attached.
❏ Do not attach the control pad with double-side tape or magnets.
Check that the control pad is operating correctly before attaching it with the screws.

Secure the AC adapter
Secure the AC adapter holder to the wall using M4 screws (×4)

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Slide the AC adapter into the holder and connect the power cable.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Connect the projector cables to the control pad
See the connection example on page 19 for details.

Attach the front cover

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Installing the pen stand
The pen stand is included with the BrightLink 1485Fi/1485Fi+/EB-725Wi/EB-735Fi /EB-760Wi/EB-770Fi. You can secure the pen stand with commercially-available M4 screws (not included) or the attached magnets.

Secure the pen stand:

  • If your whiteboard is magnetic, you can use the magnets on the back of the pen stand to secure it.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 133 You need to leave a gap of at least 3.9 inches (100 mm) between the pen stand and the left or right side of the projected image or the touch feature may not function properly. If you are unable to leave this gap, install the pen stand on the wall next to the whiteboard.
  • If you don’t have a magnetic whiteboard or are unable to fit the pen stand on the whiteboard with the proper gap around the projected image, use commercially-available M4 screws (not included) to secure it to the wall.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Attach the pen stand cover.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

Appendix

Using the Easy Interactive Function
After you install your BrightLink projector (and the Touch Unit, if applicable), you need to perform calibration to align the positions of the cursor and your interactive pen(s) (and finger, if the Touch Unit is installed). See the projector’s online User’s Guide or Start Here folder for detailed instructions.
In order to use the Easy Interactive Tools software, you must first install the software on your computer. Mac users also need to install a driver that enables pen or finger touch interactivity to work. Both software programs are available for download.
For details, see the online User’s Guide or visit the following site and search for your product:
U.S.: http://epson.com/support/brightlinkdownloads
Canada: http://epson.ca/support/brightlinkdownloads
Latin America: http://latin.epson.com

Using Auto Screen Adjustment
If possible, avoid adjustments with the Auto Screen Adjustment, Quick Corner, or Keystone functions of the projector. Doing so may result in a reduction in image quality and pen or finger touch calibration.

The Auto Screen Adjustment feature automatically corrects the position and shape of any image that is 110 inches or smaller diagonally. This feature is only available on the BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+/ EB-725Wi/EB- 735Fi/EB-760Wi/EB-770Fi.
Make sure you select the correct Screen Type setting before performing the Auto Screen Adjustment. Changing the Screen Type will reset any screen adjustments. See page 66 for more information.
The Auto Screen Adjustment may not work properly if:
❏ The projection surface is not flat.
❏ There are patterns, obstructions, or dirt/debris on the projection surface.

  1. Place one corner marker in each corner of the intended image location.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 136 The corner marker stickers can only be placed once. If you want to re-use the markers, attach them to the included magnets.

  2. Press the [Menu] button on the remote control or control panel.
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 137BrightLink EB-725Wi/EB-735Fi/EB-760Wi /EB-770Fi:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 144

  3. Select Installation.

  4. Select Auto Screen Adjustment.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 138

  5. Loosen all of the adjustment dials and screws.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 139

  6. Adjust the projector position so that the corner markers are completely within the highlighted areas in the corners of the image.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 140

  7. Tighten any adjustment dials and screws that you previously loosened.
    Warning
    Tighten all screws firmly. Otherwise, the projector or wall mount may fall and cause personal injury or property damage.

  8. Open the front cover (1).

  9. Use the focus lever to adjust the focus (2).
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 141BrightLink EB-725Wi/EB-735Fi/EB-760Wi /EB-770Fi:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 142

  10. After you finish making the adjustment, close the front cover.

  11. Press the [Enter] button on the remote control or control panel to begin the adjustment.
    Once the adjustment is complete, you can use the Quick Corner setting to make further adjustments.
    Using the Arc Correction or Point Correction options will reset your previous adjustments.

Making Additional Screen Adjustments
If possible, avoid adjustments with the Auto Screen Adjustment, Quick Corner, or Keystone functions of the projector. Doing so may result in a reduction in image quality and pen or finger touch calibration.
Correcting the Image Shape on a Curved Screen
If you are projecting on a curved screen, adjust the Arc Correction setting to correct the image shape.
Touch unit installation requires a projection surface that is flat, smooth, and unwarped with no more than 0.2 inch (5 mm) of unevenness in any direction on the screen surface.

  1. Press the [Menu] button on the remote control or control panel.
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 143BrightLink EB-725Wi/EB-735Fi/EB-760Wi/EB-770Fi and PowerLite EB-720/EB-725W/EB-750F/EB755F/EB-760W/EB-770F/EB-775F:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 144

  2. Select Installation.

  3. Select Geometry Correction.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 145

  4. Select Arc Correction.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 146

  5. Select the area that you want to correct.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 147

  6. Use the arrow buttons on the remote control or control panel to change the shape of the selected area.

  7. Repeat steps 5 and 6 to adjust any additional areas.

Correcting the Corner Shape
You can adjust the shape of the image corners with the Quick Corner setting.

  1. Press the [Menu] button on the remote control or control panel.
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 153BrightLink EB-725Wi/EB-735Fi/EB-760Wi/EB-770Fi and PowerLite EB-720/EB-725W/EB-750F/EB755F/EB-760W/EB-770F/EB-775F:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 149

  2. Select Installation.

  3. Select Geometry Correction.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 150

  4. Select Quick Corner.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 151

  5. Select the corner that you want to correct.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 152

  6. Use the arrow buttons on the remote control or control panel to change the shape of the selected corner.

  7. Repeat steps 5 and 6 to adjust any additional corners.

Correcting the Image Shape at Individual Points
You can adjust the image at specific points with the Point Correction setting.

  1. Press the [Menu] button on the remote control or control panel.
    BrightLink 1480Fi/1480Fi+/1485Fi/1485Fi+ and PowerLite EB-800F/EB-805F:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 153BrightLink EB-725Wi/EB-735Fi/EB-760Wi/EB-770Fi and PowerLite EB-720/EB-725W/EB-750F/EB755F/EB-760W/EB-770F/EB-775F:Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 154

  2. Select Installation.

  3. Select Geometry Correction.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 155

  4. Select Point Correction.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 156

  5. Select the point on the grid that you want to correct.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 157

  6. Use the arrow buttons on the remote control or control panel to change the shape of the selected point.Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays - fig 158

  7. Repeat steps 5 and 6 to adjust any additional areas.

Attaching a Security Cable
If the projector is to be installed in a room where it will be left unattended, you can use a commercially available theft-prevention wire lock to secure the projector to a post or other object to prevent someone from taking it.
Pass the wire for the theft-prevention wire lock through the security cable installation point.
For details on how to lock the wire lock, refer to the User’s Guide supplied with the wire lock.

![Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays

If applicable, make sure you leave the remote control, batteries, interactive pen(s), and pen tray in the room with the projector. If your projector came with a product-specific installation guide or an installation leave-behind list, use that list instead of this one. The accessories included with the projector vary by model and region.

© 2023 Epson America, Inc., 3/23
CPD-58124R3

Documents / Resources

| Epson V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays [pdf] Installation Guide
V12HA06A05 Adjustable Wall Mount For Ultra Short Throw Laser Displays, V12HA06A05, Adjustable Wall Mount For Ultra Short Throw Laser Displays, Ultra Short Throw Laser Displays, Throw Laser Displays, Laser Displays
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Epson User Manuals

EPSON Moverio BT-40 Personal Second-Screen Smart Glasses Instruction Manual
Epson
EPSON SURECOLOR P9570 44 Inch Wide-Format Inkjet Printer Instruction Manual
Epson
EPSON 2350 Cinema 4K Smart Gaming Projector User Guide
Epson
EPSON S1C31 Cmos 32-Bit Single Chip Microcontroller User Manual
Epson
EPSON M Series Wristband Instruction Manual
Epson
EPSON TM-T88V POS Receipt Printer User Manual
Epson
EPSON EcoTank Pro T542120-S Printer Ink Bottle Owner’s Manual
Epson
EPSON ELPDC30 DC-30 Document Camera User Guide
Epson
EPSON EB-PU2010B Multimedia Projector User Guide
Epson
Epson WF-M4119 WorkForce Inkjet Printers User Guide
Epson
EPSON V850 Pro Photo Scanner User Guide
Epson
EPSON WF-C5890 Series Start Here Instruction Manual
Epson
EPSON ELPFT01 Touch Unit User Guide
Epson
EPSON WF-C5310 Single Function Inkjet Printers User Guide
Epson
EPSON P6570 24 Inch Wide Format Dual Roll Printer User Guide
Epson
EPSON WF-C579R Work Force Printer User Guide
Epson
EPSON CPD-60355-R2 Series SureColor Resin Signage Printer User Guide
Epson
EPSON IWSLD500E1 Preferred SM Plus Exchange Commercial Service Installation Guide
Epson
EPSON Preferred SM Plus On Site Commercial Service User Guide
Epson
EPSON SC-F11000H Series Textile Printer User Guide
Epson

Related Manuals

SAMSUNG SRF662BFH4 French Door Fridge Instructions
Samsung
WINGS URBANA Smart Watch User Manual
WINGS
BOSCH SPS4HKI45G Dishwasher Instruction Manual
Bosch
WABASH WTCI STREAMING TV User Guide
WABASH
AXAGON ACU-QC19 wall charger Instruction Manual
AXAGON
BELLATERRA HOME 400700-20-CE Vanity Cabinet Instructions
BELLATERRA HOME
VEVOR AD110003 Pivoting Utility Fan Owner’s Manual
VEVOR
QJE QJ1503C Regulated Power Supply User Manual
QJE
Arctic King AC05ESWCR1RCM Chest Freezer Instruction Manual
Arctic King
WIZZILAB UM-1 RTLS and Communication Module User Manual
WIZZILAB
EBECO Cableflex 6 Floor Heating Cable Instruction Manual
EBECO
Flynama ES289603AAK-E Portable Electric Clothes Dryer Instruction Manual
Flynama
EBL RM-76 Professional Care On Batteries and Chargers User Guide
EBL
ARTUSI AFGR1047B 100cm Freestanding Cooker Owner’s Manual
ARTUSI
Geek L-F502 Fingerprint Lock User Manual
GEEK
BOSCH 150 CE GST Professional Straight Saw Instruction Manual
Bosch
KitchenAid KES6403 Semi-Automatic Espresso Machine Owner’s Manual
KitchenAid
WISETRACKER Wristband Smart Watch User Manual
WISETRACKER
LIFESPAN KIDS Bloom Growable Swing Set User Manual
LIFESPAN KIDS
TOW SMART 740M Steel Boomerang Hitch Pin Installation Guide
TOW SMART
hlins HD-250 Shock Absorber Harley Davidson Pan America Instruction Manual
HLINS
EMOS ZR1422 LED Panel Instructions
EMOS
KERBL 82806 222 x 115 x 200 cm Hen House Instruction Manual
KERBL
FANATEC P1 V2 CSL Steering Wheel User Guide
FANATEC
Lenove SE-A61UW Wireless Charging Dock for Smart Clocks User Guide
Lenove
SHARKEYE BE4WLA BigEye 4 Wheel Laser Aligner User Guide
SHARKEYE
INTERMOTIVE IDLE601 Vehicle Control Systems Instruction Manual
INTERMOTIVE
Beluk CX Plus Power Factor Controller Instruction Manual
Beluk
TRIANGLE HIFI AIO3 Wireless Bluetooth WiFi Speaker Owner’s Manual
TRIANGLE HIFI
SAMSUNG QA65Q70CAKLXL 4K Ultra HD Smart QLED TV Instructions
Samsung
Contact Us   Privacy Policy   30.97ms