Skullcandy Grind Series Earbuds User Guide

: June 4, 2024
: Skullcandy

Skullcandy Grind Series Earbuds

Download the Skullcandy App

|

Auto Power – On/Off

Auto On – Open Lid
Auto Off – Close Lid

Power – On

Left Earbud or Right Earbud

Power – Off

Left Earbud or Right Earbud

Pairing Mode

Left Earbud or Right Earbud
*On Mode

Pair New Device

“Grind”
Pair New Device

Play/Pause Answer/End

Left Earbud or Right Earbud
*While On

Volume Up

Right Earbud
*While Audio is Playing

Volume Up
Volume +

Volume Down

Left Earbud
*While Audio is Playing

Volume Down
Volume –

Right Earbud – “Share”
Left Earbud – “Join”
*While On

Share Audio

Re-Sync Earbuds

Both Earbuds
While On
Bluetooth Disconnected

Re-sync earbuds

Re-Sync Earbuds Find With Tile Reset Paired Device List ™

Both Earbuds
*Tile App Required

Pair Tile™

Spotify Tap™

Left Earbud Only
While On
Spotify App Required

One Touch to Spotify

Reset Paired Device List

Right Earbud Only
While ON
Bluetooth Disconnected

Reset Device

Charge Earbuds

*Close Lid To Charge

Charge Earbuds

Charge the Case

Charge Case

Voice Control

*Skullcandy App Required

Voice Control Commands

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different fromb that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help

ISED Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1 )This device may not cause interference.
(2)This device must accept any interference, including interference that may cause undesired operation of the device.

ISED SAR Compliance Statement
This equipment complies with ISED radiation exposure limits set forth
for an uncontrolled environment. End user must follow the specificoperating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

EN Contains Li-ion battery. Battery must be recycled or disposed of properly.

EN Made in China

Hardware Version:
revD1 (Earbuds) /
revC1 (Charge Case)
Software Version:
v4.5 (Earbuds) /
v1.0.0.6 (Charge Case)

Grind
GrindXT

MODEL: S2GTW
FCC ID: Y22-S2GTW
IC: 10486A-S2GTW