ABAC G-811TI Pneumatic Tool Kit User Guide
- June 1, 2024
- ABAC
Table of Contents
ABAC G-811TI Pneumatic Tool Kit
Product Information
- Max Air Pressure: 8 bar
- Air Consumption: Depends on usage
- Sound Pressure Level: Varies
- Pneumatic Hose Length: 400 cm
- Weight: 0.3 kg
Product Usage Instructions
Operating Procedures:
- Connect the compressed air supply to fitting A.
- Connect the inflation fitting B to the valve of the wheel and check the pressure on gauge C.
- Press the trigger D to inflate and keep checking the pressure on the gauge.
- If the pressure is too high, press trigger D halfway to restore the correct pressure.
- To avoid damage to the pressure gauge, do not let the tyre inflator fall on hard surfaces.
- Use one of the adapters included in kit (E) to inflate the bike’s inner tubes, balls, or other devices.
Maintenance:
- Disconnect the air supply during maintenance on the tool.
- Regularly clean and dry the filter in the system and the pneumatic tool air inlet opening.
- Lubricate any quick-disconnect coupling on the system to prevent jamming.
- Drain condensation from the air filter and the compressor daily.
- Clean and lubricate the tool after each use to prevent rust formation and minimize wear.
- Check the tool regularly for loose bolts/screws or parts.
- In case of power loss, have the tool repaired by trained engineers only.
Safety Instructions:
During tool usage, ensure there are no open flames or flammable vapours in
the working environment. Always wear a protective mask and disconnect the tool
when not in use.
Frequently Asked Questions (FAQ)
-
Q: How often should I clean the filter in the system?
A: It is recommended to regularly clean and dry the filter in the system to ensure optimal performance. Cleaning it after each use is ideal. -
Q: Can I use this tool to inflate other devices apart from tyres?
A: Yes, you can use one of the adapters included in the kit to inflate the bike’s inner tubes, balls, or other inflatable devices.
TECHNICAL SPECIFICATIONS
| Air pressure max, Pressione pneumatica max. | bar | 8 |
|---|---|---|
| Nozzle diameter | [mm] | – |
| Suction cup | [ml] | – |
| Air consumption | [l/s] | – |
| Sound pressure level (LPA) acc. to. EN ISO 15744 | [dB(A] | – |
| Spray pipe length | [mm] | 400 |
| weight | [kg] | 0,3 |
SAFETY WARNINGS
- Never point the tool at yourself or other persons.
- Do not use the tool improperly
- Always disconnect the tool when not in use.
- Keep the tool out of reach of children
WARNING!
WHEN USING THE TOOL, MAKE SURE THAT THERE ARE NO NAKED FLAMES OR FLAMMABLE
FUMES IN THE WORKING ENVIRONMENT, WEAR A PROTECTIVE MASK AND ALWAYS DISCONNECT
THE TOOL WHEN NOT IN USE.
OPERATING PROCEDURES:
- Connect the compressed air supply to fitting A. Connect the inflation fitting B to the valve of the wheel and check the pressure on gauge C. Press trigger D to inflate and keep checking the pressure on the gauge: if the pressure is too high, press trigger D half-way to restore the correct pressure. To avoid damage to the pressure gauge do not let the tyre inflator fall on hard surfaces, to ensure a correct pressure value reading.
- Use one of the adapters included in the kit (E) to inflate bike inner tubes, balls or other devices
MAINTENANCE
- Disconnect the air supply during maintenance on the tool.
- Regularly clean and dry the filter in the system and the pneumatic tool air inlet opening.
- Lubricate any quick-disconnect coupling on the system to prevent jamming.
- Drain condensation from the air filter and the compressor daily.
- To avoid rust formation and to minimize wear, clean and lubricate the tool after each use.
- Check the tool regularly for loose bolts/screws or parts.
- In case of power loss: have the tool repaired.
- Only trained and qualified engineers are allowed to adjust or repair the tool.
What’s In The Box
- 1pcs bike adapter
- 1pcs ball needle
- 1pcs universal needle for inflating devices
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>