VEVOR LI5-01 Electric Cooktop Induction Stove Top User Manual
- May 15, 2024
- VEVOR
Table of Contents
InductionHobUserManual
MODEL:LI5-01
Technical Support and E-Warranty Certificate
www.vevor.com/support
We continue to be committed to provide you tools with competitive price.
“Save Half”, “Half Price” or any other similar expressions used by us only
represents an estimate of savings you might benefit from buying certain tools
with us compared to the major top brands and doses not necessarily mean to
cover all categories of tools offered by us. You are kindly reminded to verify
carefully when you are placing an order with us if you are actually saving
half in comparison with the top major brands.
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact
us:
CustomerService@vevor.com
This is the original instruction, please read all manual instructions
carefully before operating. VEVOR reserves a clear interpretation of our user
manual. The appearance of the product shall be subject to the product you
received. Please forgive us that we won’t inform you again if there are any
technology or software updates on our product.
| Warning-To reduce the risk of injury, user must read instructions manual
carefully.
---|---
| This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:(1)This device may not
cause harmful interference, and (2)this device
must accept any interference received, including interference that may cause
undesired operation.
| This product is subject to the provision of European Directive
2012/19/EC. The symbol showing a wheelie bin crossed
through indicates that the product requires separate refuse collection in the
European Union. This applies to the product
and all accessories marked with this symbol. Products marked as such may not
be discarded with normal domestic waste,
but must be taken to a collection point for recycling electrical and
electronic devices
BEFORE USE
IMPORTANT: The cooking zones will not switch on if pots are not the right
size. Only use pots bearing the symbol “INDUCTION SYSTEM” (Figure below) or
enameled pots. Place the pot on the required cooking zone before switching the
hob on. EXISTING POTS AND PANS
Use a magnet to check if the pot is suitable for the induction hob: pots and
pans are unsuitable if not magnetically detectable.
-
Make sure pots have a smooth bottom, otherwise they could scratch the hob. Check dishes.
-
Never place hot pots or pans on the surface of the hob’s control panel.
This could result in damage. -
The bottom diameter of pots or pans should be at least 10cm.
SAFETY INSTRUCTIONS
YOUR SAFETY AND THAT OF OTHERS ARE VERY IMPORTANT
This manual and the appliance itself provide important safety messages, to
be read and always observed.
**** This is the warning / caution-safety symbol, regarding safety, warning
of potential risks to users and other
All messages relevant to safety specify the potential risk to which they refer
and indicate how to reduce the risk of injury, damage and electric shocks due
to incorrect use of the appliance. Make sure to comply with the following:
-
The appliance must be disconnected from the power supply before carrying out any installation operation.
-
Installation and maintenance must be carried out by a specialized technician, in compliance with the manufacturer’s instructions and the local safety regulations in force. Do not repair or replace any part of the appliance unless specifically stated in the user manual.
-
The appliance must be earthed.
-
The power cable must be long enough to connect the appliance, fitted in the cabinet, to the power supply.
-
For installation to comply with the current safety regulations, an omnipolar switch with a minimum contact gap of 3mm is required.
-
Do not use multi-sockets or extension cords.
-
Do not pull the appliance’s power cable.
-
The electrical parts must not be accessible to the user after installation.
-
The appliance is designed solely for domestic use for cooking food. No other use is permitted (e.g. heating rooms). The Manufacturer declines any liability for inappropriate use or incorrect setting of the controls.
-
WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements.
Children less than 8 years old shall be kept away unless continuously supervised. -
The accessible parts can become very hot during use. Children must be kept away from the appliance and watched over to ensure they do not play with it.
-
Do not touch the appliance heating elements during and after use. Do not allow the appliance to come into contact with cloths or other flammable materials until all the components have cooled sufficiently.
-
Do not place flammable materials on or near the appliance.
-
Overheated oils and fats catch fire easily. Pay attention when cooking food products rich in fat and oil.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand hazards involved. Children shall not play with the appliance.Children shall not make cleaning and user maintenance without supervision. -
An air switch or circuit breaker (not supplied) should be installed in the compartment under the appliance.
-
If the surface is cracked, switch off the appliance to avoid the possibility of electric shock.
-
The appliance is not intended to be operated by means of an external timer or separate remote control system.
-
WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire. NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.
-
WARNING: Danger of fire: do not store items on the cooking surfaces.
-
Do not use steam cleaners.
-
Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot.
-
After use, switch off the hob element by its control and do not rely on the pan detector.
-
CAUTION! Surface remains hot after use! Do not touch the top plate right after removing the pot or the pan, as the top plate will still be very hot.
INSTALLATION
After unpacking the product, check for any damage during transport. In case of
problems, contact the dealer or the After-Sales Service.
For built-in dimensions and installation instruction, see in below
figures
- **** The distance between the underside of the appliance and the separator panel must respect the dimensions given in the figure (mini. 50mm).
- In order to ensure the correct operation of the product, do not obstruct the minimum required clearance (min. 20 mm) on the worktop for air flow out.
- If an undertop oven is installed, make sure the oven is equipped with a cooling system.
- Do not install the hob above a dishwasher or washing-machine, so that the electronic circuits do not come into contact with steam or moisture which could damage them.
ELECTRICAL CONNECTION
-
**** Disconnect the appliance from the power supply.
-
Installation must be carried out by qualified personnel who know the current safety and installation regulations.
-
The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter.
The power cable must be long enough to remove the hob from the worktop. -
Make sure the voltage specified on the rating label located on the bottom of the appliance is the same as that of the home.
INSTRUCTION FOR USE
** To avoid permanently damaging the glass-ceramic top, do not use:
Pots with bottoms that are not perfectly flat.
Metal pots with an enameled bottom.
CONTROL PANEL LAYOUT Switching the hob
On/Off
To switch the hob on, press the button and the cooking zone displays light up.
To switch off, press the same button until the displays switch off. All the
cooking zones are deactivated If the hob has been in use, the residual heat
indicator “H” remains lit until the cooking zones have cooled down.
If no heating zone is selected within 120 seconds of switching on, the hob
switches off automatically.
Switching on and adjusting cooking zones
Once the hob is switched on and the pan is positioned on the chosen cooking
zone, select the zone using the corresponding button: the display shows level
0.Each cooking zone has various power levels, adjustable with the buttons ,
going from “1”: min. level, to “9”: max. level.
Deactivation of cooking zones**
Select the cooking zone you wish to switch off. Press the corresponding
button.
Press the key “ ” to set the level to “0”. The cooking zone switches off and
the residual heat indicator “H” lights up.
Child lock
This function locks the controls to prevent accidental switching on of the
hob. To activate the child lock function, switch on the hob and hold button
for three seconds; the timer shows Lo. Then the control panel is locked.
To deactivate the control panel lock, repeat the activation procedure. The Lo
goes off and the hob is active again.
Timer
The timer can be used to set cooking time for a maximum of 99 minutes (1 hour
and 39 minutes) for all cooking zones.
Select the cooking zone to be used with the timer, press the button with the
clock symbol then set the desired cooking time using the buttons of the timer function (see figure). After a few
seconds, the timer begins the countdown.
Once the set time has elapsed, an acoustic signal sounds and the hob switches
off automatically.
To deactivate the timer, press the “ ” button to set the display showing “00”
or hold the button with the clock symbol for at least 4 seconds.
Booster
When this button is pressed, the cooktop stops at Max Power in five minutes.
Press the Button again, and the cooktop will return to the last setting.
** Please do not place hot pots or pans on the keypad! This could cause
damage.
Auto switch off**
The hob will automatically switch off when you did not set cooking time,
forgot to switch off the hob, and did not operate the hob for two hours.
CONTROL PANEL WARNINGS
Residual heat indicator
The hob is fitted with a residual heat indicator for each cooking zone. These
indicators alert the user when cooking zones are still hot.
If the display shows , the cooking zone is still hot. If the residual heat
indicator of a given cooking zone is lit, that zone can be used, for example,
to keep a dish warm or to melt butter.
When the cooking zone cools down, the display goes off.
Incorrect or missing pot indicator – Error code “E0”
If you are using a pot that is not suitable, not correctly positioned or not
of the correct dimensions for your induction hob, the symbol ”E0” mean “no
pot” will appear in the display (see figure at side). If no pot is detected
within 180 seconds, the hob switches off.
TEMPERATURE LEVEL TABLE
Temperature level| Type of cooking| Level use (indicating cooking experience
and habits)
---|---|---
Max level| 9| Frying –
boiling| Ideal for browning, starting to cook, frying deep frozen products,
fast boiling
High level| 7-8| Browning –
sautéing –
boiling –
grilling| Ideal for sautéing, maintaining a lively boil, cooking and grilling
| 6-7| Browning —
cooking —
stewing –
sautéing –
grilling| Ideal for sautéing, maintaining a light boil, cooking and grilling ,
preheating
accessories
---|---|---|---
Medium level| 4-5| Cooking —
stewing –
sautéing –
grilling| Ideal for stewing, maintaining a gentle boil, cooking (for a long
period of time).
Creaming pasta
3-4| Cooking — simmering
— thickening – creaming| Ideal for long-cooking recipes (rice, sauces, roasts,
fish) with liquids (e.g. water, wines, broth, milk), creaming pasta
2-3| Ideal for long-cooking recipes (less than a liter in volume: rice,
sauces, roasts, fish) with liquids (e.g. water, wines, broth, milk)
Low level| 1-2| Melting — defrosting
— keeping
— food
warm – creaming| Ideal for softening butter, gently melting chocolate, thawing
small products and keeping just-cooked food warm (e.g. sauces, soups,
minestrone)
1| Ideal for keeping just-cooked food warm, for creaming risottos and for
keeping serving dishes warm (with induction-suitable accessory)
Power off| 0/H| Support surface| Hob in stand-by or off mode (possible end-of-
cooking residual heat, indicated by an “H”)
Note: The data in the table is for guidance only. The relation between
the heat setting and the cooking zone consumption of power is not linear. When
you increase the heat setting it is not proportional to the increase of the
cooking zone consumption of power.
The power of the cooking zones can be different in some small ranges. It
changes with the material and dimensions of the cookware.
TECHNICAL INFORMATION
Voltage: 220 – 240V, 50/60 Hz
Max. power: 9200W
Top Left: 1800W BOOSTER 2000W
Top Right: 1500W BOOSTER 1800W
Middle: 2000W BOOSTER 2200W
Down Left: 1500W BOOSTER 1800W
Down Right: 1800W BOOSTER 2000W
Only one zone can be use the function of “Boost“ at the same time per left or
right side.
CLEANING
-
**** Do not use steam cleaners.
-
Before cleaning, make sure the cooking zones are switched off and that the residual heat indicator (“H”) is not displayed.
IMPORTANT: Do not use abrasive sponges or scouring pads. Their use could eventually ruin the glass. -
After each use, clean the hob (when it is cool) to remove any deposits and stains due to food residuals.
-
Sugar or foods with a high sugar content damage the hob and must be immediately removed.
-
Salt, sugar and sand could scratch the glass surface.
-
Use a soft cloth, absorbent kitchen paper or a specific hob cleaner (follow the Manufacturer’s instructions).
TROUBLESHOOTING GUIDE
Read and follow the instructions given in the section “Instructions for use”.
- Check that the electricity supply has not been shut off.
- Dry the hob thoroughly after cleaning it.
- If, when the hob is switched on, alphanumeric codes appear on the display, consult the following table for instructions.
- If the hob cannot be switched off after using it, disconnect it from the power supply.
Error code | Possible Cause | Remedy |
---|---|---|
E0 | No Pan or did not detect | |
the pan | Put on the pan | |
E2 | NTC short or open | Contact the after-sales service |
and specify the error code
E3| High voltage| Contact the after-sales service
and specify the error code
E4| Low voltage| Contact the after-sales service
and specify the error code
E5-E
8| A lot of possibilities, the
cooktop must be sent in
for repair| Contact the after-sales service
and specify the error code
- C/C-C-C-C Error: automatic safety shut-off for liquid overflow
- This means that the touch panel was watered with liquid.
NOISES MADE BY THE HOB
Induction hobs can make whistling or crackling sounds during normal operation,
these actually come from the pots and pans as a result of the characteristics
of the bottoms (for example, bottoms made of several layers of material, or
uneven bottoms). These noises vary depending on the pots and pans used and the
amount of food they contain, and are not indicative of a defect of any kind.
In addition, the induction hob is equipped with an internal cooling system to
control the temperature of electronic parts; as a result, during operation and
for several minutes after the hob has been switched off, the noise of the
cooling fan will be audible.This is perfectly normal and essential for proper
appliance functioning.
AFTER-SALES SERVICE
Before contacting the After-sales Service:
- See if you can solve the problem yourself with the help of the “Troubleshooting guide”.
- Switch the appliance off and then on again it to see if the problem has been eliminated.
If the problem persists after the above checks, contact the nearest After-
Sales Service.
Always specify:
- a brief description of the fault
- the product type and exact model
- your full address
- your telephone number
If any repairs are required, contact an authorized After-Sales Service Centre
(to ensure the use of original spare parts and correct repairs).
Spare parts are available.
Energy saving
For optimum results, it is advisable to:
- Use pots and pans with bottom width equal to that of the cooking zone.
- Only use flat-bottomed pots and pans.
- When possible, keep pot lids on during cooking.
- Use a pressure cooker to save even more energy and time.
- Place the pot in the middle of the cooking zone marked on the hob.
Technical Support and E-Warranty Certificate
www.vevor.com/support
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>