BRESSER BR-100RGB LED Studio Light Instruction Manual

BR-100/150RGB
LED Studio Light
Art. No. F005103
F005104 INSTRUCTION MANUAL

BR-100RGB LED Studio Light

Visit our website via the following QR Code or web link to find further information on this product or the available translations of these instructions.

|
---|---
www.bresser.de/PF005103| www.bresser.de/PF005104

WARRANTY

www.bresser.de/warranty_terms

GENERAL WARNINGS

DANGER OF BODILY INJURY!
Do not use in the presence of children or animals. Store out of reach of children and animals.
RISK OF MATERIAL DAMAGE!
Make sure that no one can trip over connection cables of the device. The device could be knocked over.
Only use the recommended power cable or the recommended battery for the power supply!
The manufacturer accepts no liability for voltage damage caused by the use of an unsuitable power supply!
DANGER OF AN ELECTRIC SHOCK!
This device contains electronic parts that are powered by a power source (power adapter). Only use the device as described in the manual. Otherwise, you run the DANGER of an ELECTRIC SHOCK.
Never bend, squeeze or pull power cables, connecting cables, extensions or connectors.
Protect cables from sharp edges and heat.
Check this device, cables and connections for damage before use.
Never attempt to operate a damaged device, or a device with damaged electrical parts!
Damaged parts must be replaced immediately by an authorized service agent.
Operate the device only in a completely dry environment and do not touch the device with wet or damp body parts.
RISK OF GLARE!
Make sure that people and animals do not look into the light. The high luminosity can cause glare to the eyes and afterimages. This impairment of vision can lead to accidents.
FIRE/EXPLOSION HAZARD!
Always place the device in such a way that it cannot tip over and ensure that it is stored in a reasonably safe place.

• Keep children and animals away from the device! They could knock the device over.
• Make sure that no one can trip over connection cables. The device could be knocked over.
• Do not expose the device to high temperatures. Do not short-circuit the device or dispose of in fire! Excessive heat and improper handling can cause short circuits, fires and even explosions!
• Only use the recommended power supply*!

IMPORTANT NOTE!
Do not disassemble the device! In the event of a defect, please contact your dealer.
They will contact the Service Center and can arrange the return of this device for repair if necessary.
Disconnect the power supply by pulling the mains plug when the appliance is not in use, in case of a longer interruption of operation and before any maintenance and cleaning work.
Place your device so that it can be disconnected from the power supply at any time. The power outlet should always be near your appliance and should be easily accessible, as the plug of the power cord serves as a disconnect device from the mains supply.
To disconnect the unit from the mains, always pull the mains plug and never pull the cable!
Do not subject the device to excessive vibrations.

PARTS OVERVIEW

Model BR-100RGB Model BR-150RGB

PARTS DESCRIPTION

1. Ventilation slots
2. V-mount battery holder(s)
3. DMX
4. Remote Control | Bluetooth
5. DMX Input | Output (RJ45)
6. U-holder
7. LED Display
8. Rotary control knob
9. MODE
10. Function
11. Tilt adjusting screw
12. Power socket
13. Power knob
14. Fixing screw for 16mm (5/8″) Spigot
15. Spigot connection hole
16. RGB LEDs
17. Barn doors

FUNCTIONS & OPERATION

CCT/HSI/FX

1. Shortly press 4 to switch between CCT and HSI control mode.

2. In the CCT mode, shortly press 7 to change the color temperature 2700K-9999K and shortly press 7 again to change the dimmer 0-100%.

3. In the CCT mode, long press 4 to change 12 special effects and related. Shortly press 7 to switch between 12 special effects, flash speed or dimmer. Turn the knob 8 to change effects from F1-12, flash speed 1-9 and dimmer 0-100%.
   12 Special effects (F1-F12)
   Pulsing / Campfire / Lightning / Ex plosion / TV / Candle / Fault Bulb / Breathe / Paparazzi / SOS / Flame / Fade

4. In the HSI mode, shortly press 7 to switch between hue, saturation and intensity. Turn the knob 8 to change hue 0-360°, saturation 0-100% or intensity 0-100%.

5. In the HSI mode, long press 4 to change 8 special effects and related. Shortly press 7 to switch between 8 special effects, flash speed or dimmer. Turn the knob 8 to change effects from F1-8, flash speed 1-9 and dimmer 0-100%.

8 Special effects (F1-F8)
Cop Car / Party / Fireworks / Disco / Ambulance / Fire Siren / RGB Loop / Welding
DMX channel selection

1. Shortly press 5 to enter DMX channel selection mode.
2. When DMX/CH is blinking, the DMX address can be changed by pressing the knob 8.
3. When DMX status is off, long pressing 6 allows to reset Bluetooth in mobile APP control mode.

not included
2.4G Remote control

1. Turn the knob 8 to select the 001-099 channel in the mode of 2.4G remote control.
2. When DMX status is off, long pressing 6 to reset bluetooth connection while using mobile APP control (NOT in DMX mode).

POWER SUPPLY & TURNING ON/OFF

NOTE!

Never operate this device with rechargeable batteries or mains power supply simultaneously to avoid any damages to the electronical parts. There is a risk of a short circuit!

Only operate the light with the recommended rechargeable batteries.
Depending on the respective model, the LED light can be equipped with one or two battery holders.
Power supply with DC power connection

1. Put the 2-pins plug of the power cable in the power socket 10.
2. Put the Euro plug of the power cable in the power outlet.
3. Move the power knob 10 to postion ‘II’ to turn on the light by using DC power supply.
4. Move the power knob  10 to postion ‘0’ to turn off the light.

*Power supply with rechargeable V-mount batteries (accessory depends on model)**

1. Slowly slide the fully loaded rechargeable V-mount battery into the holder from above until it snaps into place.
2. Move the power knob 10 to postion ‘I’ to turn on the light by using battery power supply.
3. Move the power knob 10 to postion ‘0’ to turn off the light.

APP CONTROL

This studio light can be controlled through a smart device (e.g. Tablet-PC, Smartphone) by the ‘LinkLite’ App.

1. Use the link or QR code below to download the App ‘LinkLite’.
2. Turn on the studio light and wait about 5 seconds.
3. Long press 2 to reset the bluetooth connection for the studio light.
4. Enable Bluetooth on your smart device and connect with the desired studio light model.

Once the studio light is connected, you are able to control the device through the App.
Note: If the connection failed, add the desired device manually through the App (select ‘Add device’).
APP DOWNLOAD:

https://a.smart321.com/comlinklite

*not included

ADJUSTING THE TILT ANGLE

1. Hold the LED light and slowly loosen the locking screw (12) for the tilt joint.
2. Move the light head to the desired position and tighten the locking screw (12) again hand-tight.

*MOUNTING ON A TRIPOD (optional)**

1. Loosen the fixing screw (14) for the Spigot connection hole (15) so that the opening of the Spigot connection is exposed.
2. Place the LED light with the opening on the Spigot of a tripod and tighten the fixing screw (14) firmly.

DISPOSAL

Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal.
**** Do not dispose of electronic devices in the household garbage! As per the Directive 2012/19/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.

CE DECLARATION OF CONFORMITY

**** Bresser GmbH has issued a „Declaration of Conformity“ in accordance with applicable guidelines and corresponding standards. The full text of the CE declaration of conformity is available at the following internet address:
www.bresser.de/download/BR-RGB/CE/BR- RGB_CE.pdf

WARRANTY & SERVICE

The regular warranty period is 2 years and begins on the day of purchase. To benefit from an extended voluntary warranty period as stated on the gift box, registration on our website is required.
You can consult the full warranty terms as well as information on extending the warranty period and details of our services at www.bresser.de/warranty_terms.

www.bresser.de/warranty_terms

TECHNICAL DATA

5050 RGB: 351 pcs.
Special Effects| 20 (8+12)
Flash Speed| 1-9
App Control| via LinkLite App (free of charge via download link)
Remote Control**| 99 channels; 2.4G wireless remote control
Remote Distance| up to 30m
DMX512 dimmer*| yes, via RJ45 interface connection
Battery Type| 1 x rechargeable V-mount
lithium battery 14.8V, ≥ 120W| 2 x rechargeable V-mount
lithium battery 14.8V, ≥ 120W
DC power input| DC13-19V| DC36V / 4.3A
Dimensions**| 300x300x46mm| 300x480x46mm

*not included
Service
Please contact the service centre first for any questions regarding the product or claims, preferably by e-mail.
E-Mail: service@bresseruk.com
*Telephone: +44 1342 837 098
BRESSER UK Ltd.*
Suite 3G, Eden House
Enterprise Way
Edenbridge, Kent TN8 6HF
Great Britain
Number charged at local rates in the UK (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs.
Err ors and technical changes r eserved. · Fouten en technische wijzigingen voorbehouden. · Irrtümer und technische Änderungen vorbehalten.
Manual_F005103-F005104_BR-100RGB-150RGB_en-nl-de_BRESSER_v022024a

Bresser GmbH
Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de
@BresserEurope
Bresser UK Ltd.
Suite 3G, Eden House Enterprise Way
Edenbridge, Kent TN8 6HF
Great Britain

References

• Bresser | Startseite | Expand Your Horizon mit BRESSER
• Linklite

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>