ideal lux Aria SP1 Suspension Lamp Instruction Manual

ideal lux Aria SP1 Suspension Lamp

Product Specifications

• Model: Aria SP1
• Socket Type: E27
• Maximum Wattage: 1 x 60W
• Voltage: 220-240V, 50/60Hz
• Color: BIANCO
• Barcode: 8021696059679

Product Usage Instructions

Installation:

1. Ensure installation is carried out by a qualified electrician.
2. Follow the assembly instructions in numerical order.
3. The lighting fitting should be installed as per the provided guidelines.

Safety Instructions:

1. Always disconnect the power supply before installation or maintenance.
2. Use appropriate fixing accessories for different materials.
3. Do not disassemble the product or attempt to replace LED light sources.
4. In case of damage to the external power cable, it should be replaced by the manufacturer, retailer, or a qualified electrician.

Electrical Safety Classes:

• Class I: Requires grounding for electrical safety.
• Class II: Does not require grounding due to double insulation or reinforced insulation.
• Class III: Operates on very low voltage (below 50 Volts) and does not require grounding.

Protection Ratings:

• IPX0: Not protected.
• IPX1-IPX8: Varying degrees of protection against solid objects and moisture.

Frequently Asked Questions (FAQ):

• Q: Can the LED light sources be replaced?
  A: No, the LED light sources are not replaceable. Do not attempt to disassemble the product.

• Q: What should I do if the lamp does not turn on?
  A: If the lamp does not turn on, try replacing the fuse inside the product.

• Q: Is grounding mandatory for this product?
  A: Yes, grounding is mandatory for Class I electrical safety.

Instructions

THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.

Suspension lamp

Assembly Instructions

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION. THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.

SAFETY INSTRUCTIONS

1.  This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
5. Always isolate power before commencing installation, maintenance or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors.
10. Luminaires not suitable for recessed on normally flammable surfaces.
11.  Luminaire not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing to the ceiling.
13. This fitting is only suitable for fixing to the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
15. Only use lamps which do not exceed the maximum specified wattage.
16. Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
18.  Cracked or broken safety glass has to be replaced immediately. Use only manufacturer approved parts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class I Electrical safety guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory
22. Class Il Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
23. Class III Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
24. Not protected.
25. Protected against solid objects greater than 50 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against solid objects greater than 2,5 mm.
28. Protected against solid objects greater than 1mm.
29. Dust protected
30. Totally protected against dust infiltration.
31. Not protected.
32. Protected against vertically falling water drops.
33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.
34.  Protected against rain.
35. Protected against splashing water.
36. Protected against water jets
37. Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged immersion.
40.  Luminaire not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.

References

• The domain name Electrician.LA is for sale

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>