SEALEY SM521 150mm Bench Grinder User Manual
- June 1, 2024
- SEALEY
Table of Contents
SEALEY SM521 150mm Bench Grinder User Manual
MODEL NO: SM521
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
2. INTRODUCTION
Fitted with 230V induction motor and is fully guarded. Suitable for workshop use. Supplied with Ø200mm wet stone and Ø150mm dry stone, ready to use. Suitable for sharpening fine blades.
3. SPECIFICATION
4. ASSEMBLY
5. GRINDING STONES
6. OPERATION
PRE-USE INSPECTION
‰WARNING! In spect the grinder before operating the machine. Ensure the
grinder is unplugged from The mains power before commencing the inspection.
- Check the tool rest on the dry wheel is securely fixed and set at a maximum of 2mm from the grinding stone.
- Check that eye shield is in good condition, secure and that you can see through it clearly.
- Turn the dry grinding stone by hand and check for any damage. Check they do not touch the tool rest or guards and are correctly aligned. If any of the above checks fail, replace, repair, or adjust as necessary before starting the grinder.
STONE USE
Depending on the model, grinders are supplied with one or two aluminous oxide
stones. Stones have two grades, fine for hard materials and coarse for soft
materials. When grinding, should surface of the stone become “loaded” (coated
with particles of the material being ground) it is probably the wrong grade of
stone for the job.
IMPORTANT: Grinding stones MUST Only be assembled by a person holding a grinding wheel certificate. See section 5.
6.3. USING THE GRINDER
- Plug the grinder into the mains power supply.
- Place the eyeshield in its appropriate safety location.
- Switch the grinder on and bring the workpiece slowly into contact with the spinning stone, or wire wheel.
- When you have completed your task, unplug the grinder from the mains power supply, and clean the machine ready for next use.
7. MAINTENANCE
WARNING! Ensure the grinder is unplugged from the mains power supply before performing any maintenance or service.
- As the grinding stone wears, adjust the position of the tool rest. The rest must be set at a maximum of 2mm from the stone surface.
- Regularly remove the grinding stone covers and clean out any dust and dirt.
- The machine motor and bearing are sealed units and require no regular maintenance. Should you require assistance, contact your local Sealey service agent.
- For information relating to the handling and maintenance of grinding stones refer to section 5.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.
NOTE: It is our policy to continually improve products and as such we reserve
the right to alter data, specifications and component parts without prior
notice.
IMPORTANT: No Liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
sales@sealey.co.uk
© Jack Sealey Limited
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>