VEVOR YS-088 Oil Extractor User Manual

VEVOR YS-088 Oil Extractor User Manual

Technical Support and E-Warranty Certificate www.vevor.com/support

OIL EXTRACTOR USER MANUAL

Model:YS-088,YS-088A,YS-087, YS-087A,YS-087B

We continue to be committed to provide you tools with competitive price. “Save Half”, “Half Price” or any other similar expressions used by us only represent sanestimate of savings you might benefit from buying certain tools with us compared tothemajortop brands and does not necessarily mean to cover all categories of tools offered byus. You are kindly reminded to verify carefully when you are placing an order with us if youareactually saving half in comparison with the top major brands

NEED HELP? CONTACT US!

Have product questions? Need technical support? Pleasefeel freetocontact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretationofouruser manual. The appearance of the product shall be subject totheproduct you received. Please forgive us that we won’t informyouagainifthere are any technology or software updates on our product.

Warning

1. Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating.
2. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.

GENERAL SAFETY RULES

1. Gasoline, and fluids with high volatility, high corrosion, high temperature are forbidden to be applied on the extractor.
2. Do not use the unit to extract or store’ dangerous chemicals, poisons, acids, alkaline, or solvents. If such liquids are accidentally used in the unit, it must be drained immediately. 3.Do not disassemble the structure by yourself unless necessary to avoid leakage or damage to the vacuum pump.
3. The maximum temperature of the liquid is recommended not to exceed 60 degrees to avoid burns.
4. The safety precautions and instructions given in this manual are unable to cover in detail all the conditions and situations that may arise.
5. The operator and/or user must use common sense and caution when operating the product especially for any matters that are not referred to the above.
6. The use of any accessories other than those recommended by the manufacturer or stated in the instructions manual may result in injury or may cause damages.

SAVE THESE INSTRUCTIONS

MODEL AND PARAMETERS

Pneumatic/Manual
Material| PP| PP| PP| PP| PP
Quick Coupler| /| /| 1/4” NPT| 1/4” NPT| 1/4” NPT
Air supply Pressure| /| /| 0.4~0.8 Mpa| 0.4~0.8 Mpa| 0.4~0.8 Mpa

STRUCTURE DIAGRAM

Take YS-087 as an example (Pneumatic/Manual)

1. Sealing Cap
2. Manual Mode
3. Pneumatic Mode
4. Main Tube
5. Extension Tube 1+ Dipstick
6. Extension Tube 2 7.Air Inlet Valve

Take YS-088 as an example(Manual)

1. Sealing Cap
2. Manual(Handle)
3. Main Tube
4. Extension Tube 1+ Dipstick
5. Extension Tube2

COMPONENTS

NO.| Name| YS-088| YS-088A| YS-087| YS-087A| YS-087B
---|---|---|---|---|---|---
1| Oil Extractor| 1| 1| 1| 1| 1
2| Main Tube| 1| 1| 1| 1| 1
3| Extension Tube 1+ Wire| 1| 1| 1| 1| 1
4| Extension Tube 2| 1| 1| 1| 1| 1
5| Seal Ring| 2| 2| 2| 2| 2
6| Hose with Check Valve| 1| 1| 1| 1| 1
7| User Manual| 1| 1| 1| 1| 1

OPERATING INSTRUCTION

Step 1 . To make the extraction job smooth and easy, evacuatetheoil while it is warm. Cool down the engine at least 15 minutes after driving. Working temperature between:35F-140F.
Step 2 . Remove the tank cover, select a suitable tube to insert. If thehoseis not long enough, connect an extension tube to the minute, until itreaches the bottom of the oil pan

• Insert

• Counterclockwise to lock

• Extension tube connection

Step 3 . Extract Oil.

Pneumatic mode: Connect the 1/4″ NPT quick coupler totheair compressor or air source. Set the the operating pressure between0.4~0.8Mpa.

Manual mode: Close the air inlet valve. Make sure the tubes are connected tightly.

Pump the fluid extractor with your hands.

Manual

Pneumatic

Step 4. Remove the main tube clockwise. The air source must be disconnected in pneumatic mode.

Pour out the used fluid to another container and take it to the nearby disposal center for recycling.

WARNING

1. Do not extract the oil over the limit line on the tank, the bottom line helps prevent any spilling.
2. If the fluid goes over the limit line, it might flow into the vacuum chamber and cause leaking from bottom.
3. Noted that the fluid should not be over the limit line while pouring.
   

MAINTENANCE

1. Inspect periodically all parts and accessories and replace them if damaged or used.
2. Have damaged parts replaced by an authorized service center.
3. Check the nuts periodically and tighten them if they are loose.
4. Keep the product properly maintained and clean for better and safer performance. 5. After use, it is recommended to clean the product to preserve.

Sanven Technology Ltd.
Address: Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

Made In China

Technical Support and E-Warranty Certificate www.vevor.com/support

References

• Contact Us – Official VEVOR Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>