PG CL-SML3 1500 LUMEN Triple Head Solar Motion Activated Security Light Instruction Manual

PG CL-SML3 1500 LUMEN Triple Head Solar Motion Activated Security Light

WARNING:

• Your motion light is not a toy. Keep it out of reach from small children.
• Your motion light must be installed outdoors. Direct sunlight is needed for light to operate properly.
• If using a step ladder, you may require a second person to help install the solar motion light.
• Prior to installation, lay out all components and check against the part list section in this manual.
• Never look directly into the solar motion light when illuminated.
• This product is designed for outdoor use.

PRE-INSTALLATION

1. Before assembly compares package contents with list to make sure all parts are present.
2. Select a suitable location that can support the weight of the fixture. Determine the mounting method (page 2).

HARDWARE: Please read these instructions thoroughly prior to installation, then store in a safe place for future reference. Before beginning installation of the product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 15 minutes per light.

TOOLS REQUIRED(NOT INCLUDED)

IMPORTANT INFO:

• Your motion light must be installed outdoors. Direct sunlight is needed for the light to charge the internal battery most efficiently and to operate properly. Be aware of objects such as trees or property overhangs that may block the solar panel’s exposure to sunlight.
• Prior to installing the light, an initial charge is needed and should be done in the OFF position for at least 1 to 3 days in direct sunlight. Afterward, the included rechargeable battery will be charged sufficiently for operation.
• The motion sensor is very light-sensitive. For best performance at night, ensure there is no interfering light preventing the sensor from working correctly.
• If using a step ladder, you may require a second person to help install the solar motion light.
• At close range never look directly into the solar motion light when illuminated.
• This product is weather-resistant.

INSTALLATION OVERVIEW

1. Place the mounting socket in the desired position, and mark the screw points through the holes. Use a power drill and screwdrivers to fasten the socket to the chosen surface. If mounting on brick or another hard siding, use a 1/4-in drill bit to pre-drilled holes for screw anchors.
2. Buckle the motion light to the mounting socket securely, and adjust the solar panel and light heads to your desired direction.
3. In case you want to take the light off, press the handle below. Slip the light off by moving it upward.

NOTES:

• The ideal height is 8 Ft. from the ground. At such a height, the fixture will provide a detection distance of up to 25 feet.
• The motion sensor is the most sensitive as a person or object moves parallel to the sensor head.
• The motion sensor is the least sensitive if a person or object moves directly at the sensor head.
• Do not mount the fixture near a heat source like an air conditioner, vent, or furnace exhaust, or in a direction facing a reflective object or nearby light source.
• The sensor cannot be placed less than 8 Ft. from any reflective material. If the light flashes, the sensor is too close to such material. If this happens, move the light fixture.

MODE SELECTION

Mode I (Motion Sensor Mode):
Enter into Mode I by pressing the button once. The lights will stay on for 3 seconds, indicating this mode. When motion is detected, the lights will illuminate at full brightness for approximately 20 seconds. The lights won’t turn on if it is daytime.

Mode II (Dim light/Motion Sensor Mode):
Enter into Mode II by pressing the button a second time. Under this mode, the light illuminates automatically at dusk using a low-brightness energy saving mode. When motion is detected, the light illuminates at full brightness for approximately 20 seconds. When movement detection ceases, the light will revert to the low-brightness energy-saving mode.

Mode III (OFF):
Enter into Mode III by pressing the button a third time. The light will be turned off.

EYES

• DO NOT look directly at the LED lights.
• DO NOT remove the LED lights protective covering.

CARE AND MAINTENANCE

• The solar motion light is suggested to be cleaned with a damp cloth regularly. This will ensure optimal performance and battery charging.
• Never let any abrasive material come into contact with the solar panel.

This product has a two-year warranty from the date of purchase. This guarantees against failure due to factory defects, whether caused by materials or workmanship. The warranty is non-transferable and only pertains to the original purchaser. Proof of purchase is required for any repair or replacement, so please keep your proof of purchase receipt. This warranty does not cover normal wear and tear or damage due to misuse. Misuse of this product includes but is not limited to:

• Using outdoors in extreme weather conditions.
• Opening the product’s housing.
• Any attempts to update, remodel or fix the unit yourself.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>