PG CL-BSLM1000-BZ 1000Lumen Bronze Dual Head Solar Motion Sensor Outdoor Security Light Instruction Manual

PG CL-BSLM1000-BZ 1000Lumen Bronze Dual Head Solar Motion Sensor Outdoor

Security Light

PRECAUTIONS:

Please read and understand this entire manual before Installing or operating this light fixture.  Read all instructions before installation, then store in a safe place for future reference. Failure to do so may result in faully assembly and potential injury.

• Prior to installation. (3) D-cell batteries are required (batteries not included). Do not mix old and new batteries.
• This light fixture should be installed outdoors to a wall.
• Do not immerse components in liquid.
• Your motion light is water-resistant.
• Never look directly into the solar motion light When illuminated.
• Operating temperature -13•F to 113’F (2· 5’C to 45•C)

WARNING : To prevent SERIOUS I NJURY OR DEATH, never allow children near the batteries. II a battery is swallowed, seek immediate medical attention.
WARNING: When replacing tile battery, DO NOT use old batteries. DO NOT DISPOSE OF THE BATTERIES IN FIRE. BATTERIES MAY L EAK OR EXPLODE

HARDWARE:

TOOLS REQUIRED

INSTALLATION AND OPERATION INSTRUCTIONS]

BATTERY INSTALLATION

1. Remove the mounting bracket (8) from the light (A) Remove the screw on the back of the light (A). Take off the back cover to access the battery compartment.
2.  lnsen three (3) 1.SV 0-Cell Batteries(not included) into the battery chamber on the back of the light (A). Do not mix old and new batteries. Make sure the polarity is correct for each battery.
3. Close the back cover and secure it by re–attaching the screw on the back of the light (A)

LIGHT INSTALLATION

1. Using the mounting bracket (B) as your guide, drill (4) holes using a 1 /8 drill bit into the mounting surface. Insert (4) anchors (C) in the holes, then fasten the mounting bracket (8) onto the wall with (4) screws (0).
2. Once the mounting bracket (8) is secured to the surface, connect the light (A) to the mounting bracket {8).
3. Installation is complete. Turn on the light by pressing the “ON” button located on the bottom of the light.

TEST MODE:
First, press the Mode button to turn the light on. Switch the time to Test. This mode allows you to test the lights motion sensor to confirm it activates the light. Test mode will activate the light day or night. Once the light is installed, attempt to trigger the light by moving in the intended detection zone. If the light triggers on, you are now ready to move the switch to the preferred duration option. The light will now only turn on at night.

BASIC OVERVIEW
There are 3 controls

1. MODE
2. TIMER
3. SENSITIVITY

MODE

• Press the Mode button once and it will enter ‘Auto 100%’ mode: The light will turn on full brightness automatically when motion is detected at night.
• Press the Mode button twicea nd it will enter ‘30%’mode: The light will turn on with 30% brightness automatically when motion is detected at night.
• Press the Mode button a third time and it will enter ‘OFF’mode and the light will shut off.

TIME

Determine the duration of the light once motion is detected: 15 seconds, 30 seconds, or 60 seconds.

SENSITIVITY
Controls the distance of the range of motion detection. There are three selections to choose from:

1. I.LOW
2. MEOIUM
3. H/GH

CARE AND MAINTENANCE:

The light should be cleaned with a damp cotton cloth regularly. That will ensure optimal performance.

TROUBLESHOOTING:

Ille pc,,•1er oottoo andmakesure itisin Ille ON po�tion.
The battenes are a combination ofold and new. Make sure only new batteries areused.
The batteries are dead.                   Replace with new batteries.

EYES:

• DO NOT look directly atthe LED lights.
• DO NOT remove the LED lights
• protective covering

This product has a two-year limited warranty from the date of purchase. This guarantees against failure due to factory  defects, whether caused by materials or workmanship. The warranty is non-transferable and only pertains to the original purchaser. Proof of purchase Is required for any repair or replacement, so please keep your proof of purchase receipt. This warranty does not cover normal wear and tear or damage due to misuse. Misuse of this product in cludes but is not limited to:

• Using outdoors in extreme weather conditions.
• Opening the product’s housing.
• Any attempts to update, remodel or fix the unit yourself

This device complies IMth Part 15 of the FCC rules. Operation is subject to the follol’.1ng two conditions: (1) this device may not cause hannful interference.and (2) this device must accept any interference received, induding interference that may cause undesired

If you have questions or are missing parts, please contact customer service at 1-888-745-4837questions or are missing parts, please contact customer service at 1-888-745-4837

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>