Lucci decor 020275 Venezia 12 Light Round Halogen Pendant Instruction Manual

Lucci decor 020275 Venezia 12 Light Round Halogen Pendant

Venezia 12LT PENDANT
SKU# 020275
Rated Voltage 220-240V~ 50Hz

Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this product. Please keep instructions for future reference.

Warranty

• This luminaire is covered by a 12-month warranty. The warranty is from date of purchase, not the date of installation.
• If the luminaire is not assembled and installed by a licensed electrician, the warranty will be void.
• Please retain the proof of purchase and evidence of installation by a licensed electrician.
• Warranty will be void if there is any damage due to improper usage or modification to the luminaire.
• Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation requirements

• Must be assembled and installed by a licensed electrician.

• All wiring and installation of the luminaire must adhere to the latest local and national wiring rules.
  Eg. AS/NZS 3000 Electrical installations.

• This luminaire is a Class I product and must be earthed during wiring and installation.

• Do not exceed the maximum wattage rating.

• Select a suitable location for installation:

  • This product is suitable for indoor use only.
  • The mounting point must support 2 times the weight of the luminaire.
  • Ensure the luminaire is not installed in direct line of an air vent/system.
  • If installing a luminaire in an area prone to moisture, ensure that the area is well ventilated, and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.

• Take care not to pull any electrical wires during unpacking as this may damage the connection.

• Lay out all the components on a smooth surface and make sure no components are missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.

• Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.

• Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation directions

1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.

2. Remove the mounting bracket from the canopy by loosening the screws on the sides.

3. Use the mounting bracket as a template to mark the screw positions on the ceiling.

4. Install the mounting bracket onto the ceiling by using appropriately sized mounting screws and anchors.
   Ensure the screws and anchors used are suitable for the mounting surface and the surrounding environment.

5. Connect the mains supply wire and the earth cable to the terminal block.
   Mains Supply Wire                                        Luminaire Wire / Terminal Block
   Earth – Yellow/Green                               Yellow/Green
   Neutral – Blue or Black                                   Blue or N
   Live – Brown or Red                                       Brown or L
   NOTE: Ensure the wires are secure, and no bare wires are exposed.

6. Install the canopy onto the mounting bracket and secure by tightening the screws on the sides.

7. Slide the crystal over the lamp holder and lock into position by tightening the bracket end. Install the globe (not included) into lamp holder. Do not touch the bulb with your bare hands, as it may decrease the life of the bulb. Use gloves, tissue or a clean cloth.

8. After the installation, switch on the luminaire to test all the lighting functions and enjoy your new luminaire.

Safety Tips

• Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, changing the globe or making any adjustment to the luminaire.
• To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
• Select a suitable location away from liquids and hazards.
• Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
• To clean, wipe with a damp clean cloth. Do NOT soak or immerse the product in water or other liquids

Specifications

Specifications

SKU #| 020275
Colour| CRYSTAL
Rated Voltage| 220-240V~ 50Hz
Rated Wattage| 240W Max. (12 x Max.20W)
Lamp Holder| G9
Weight| 12.8kg
Canopy size| H:55mm  Dia:500mm
Dimensions| Dia: 100mm (Crystal shades)  Susp:2500mm

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>