VEVOR 1.25 inch-32mm Button Maker Instruction Manual

: June 1, 2024
: VEVOR

Table of Contents

VEVOR 1.25 inch-32mm Button Maker
Product Usage Instructions
SAFETY REMINDER
COMPONENTS
INSTALLATION STEPS
MODEL AND PARAMETER
FAILURE AND TROUBLESHOOTING
Documents / Resources

VEVOR 1.25 inch-32mm Button Maker

Specifications

Product Model: JMB-25
Manufactured Badge Specification: 25
Machine Body Color: Black
Paper Requirements: 127-157g Copper Plate Paper
Accessories With Machine:

1. 25 Metal back plate * 250
2. 25 Plastic back plates * 250
3. 25 Tin Up Cover * 500
4. 25 White paper * 20
5. 25 Transparent plastic film * 500
6. 25 Round Cutter * 1
7. Allen Key * 2
8. Magic Book * 1
9. Instruction * 1

Product Usage Instructions

Safety Reminder

This badge machine is only applied for the intended purpose. Do not apply in other applications that exceed safety considerations.
Children cannot operate this product unless accompanied by an adult.
Pay attention to safety during operation, and avoid crashing fingers.

Components

Armrest
Upper mold
Handle
Lower mold(B)
Lower mold(A)
Bottom plate
Rotating plate

Installation Steps

Put Tin up cover–Paper(pattern levelly placed)-Transparent plastic film into Lower mold(A) in sequence, then push the lower mold till up and down mold aligned.
Use one hand to hold the machine body first then stabilize the machine body by the handle, and another hand to press the machine handle till the down press to be bottom.
Put the Backplate into the Lower mold(B). Rotate the lower mold till the up and down molds are aligned.
Hand hold the machine body, right hand down press the handle till up and down mold merged to bottom.
Finish.

FAQ

Question: How do I know if I am saving half compared to top major brands?

Answer: The “Save Half, Half Price” expressions used by us are estimates of potential savings compared to major brands. Please verify carefully when placing an order to ensure actual savings.

Question: Can children operate the badge machine?

Answer: Children should not operate this product without adult supervision for safety reasons.

Question: What should I do if there are any technology or software updates on the product?

Answer: VEVOR reserves the right to interpret its user manual. The appearance of the product may vary, and updates may not be individually communicated.

We continue to be committed to providing you tools with at competitive prices.
Save Half”, “Half Price” or any other similar expressions used by us only represent an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and do not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are saving half in comparison with the top major brands.
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual.
The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

SAFETY REMINDER

This badge machine is only applied for the intended purpose. Don’t apply in other applications that exceed safety considerations.
Children cannot operate this product unless accompanied by an adult.
Pay attention to safety during operation, and avoid crushing fingers.

COMPONENTS

INSTALLATION STEPS

Put “Tin up cover Paper”(pattern levelly placed)– Transparent plastic film” into “Lower mold(A)” in sequence, then push the lower mold till up and down mold aligned.
Use one hand to hold the machine body first then stabilize the machine body by the handle, and another hand to press the machine handle till the down press to be bottom.
- (NOTE: this time down pressed mold hinge is open status.
- NOTE: Up mold hing is open status.
Put the “Backplate” into “Lower mold(B)”.
- (NOTE: Brooch should be level and not raised. Adjust the level as indicated by the top triangle.)
- Rotate the lower mold till the up and down molds are aligned.
Hand hold the machine body, right hand down press the handle till up and down mold merged to bottom.
- NOTE: Now the up mold hinge is closed status, pin passes through the hole.
Finish.
- NOTE: If use a metal back plate, then the “Lower mold(B)” needs to be placed in the plastic washer. (Metal back plate more thinner, only 58mm needs add washer, 25mm and 32mm needn’t it.)

MODEL AND PARAMETER

Product Model

Model

| JMB- 25| JMB- 32
---|---|---
Manufactured Badge Specification| Φ25| Φ32
Machine Body Color| Black| Black
Paper Requirements| 127-157g

Copper Plate Paper

| 127-157g Copper Plate Paper
Accessories With Machine| 1. Φ25 Metal back plate 250 Φ25 Plastic back plate 250

2. Φ25 Tin Up Cover *500

3. Φ25 White paper *20

4. Φ25 Transparent plastic film *500

5. Φ25 Round Cutter * 1

6. Allen Key * 2

7. Magic Book *1

8. Instruction *1

| 1. Φ32 Metal back plate 250 Φ32 Plastic back plate 250

2. Φ32 Tin Up Cover *500

3. Φ32 White paper *20

4. Φ32 Transparent plastic film *500

5. Φ32 Round Cutter * 1

6. Allen Key * 2

7. Magic Book *1

8. Instruction *1

Product Model Model	JMB- 58
Manufactured Badge Specification	Φ58
Machine Body Color	Black
Paper Requirements	127-157g Copper Plate Paper
Accessories With Machine	1. Φ58 Metal back plate * 50 Φ58 Plastic back plate

*50

2. Φ58 Tin Up Cover *100

3. Φ58 White paper *20

4. Φ58 Transparent plastic film *100

5. Φ58 Round Cutter * 1

6. Allen Key * 2

7. Magic Book 1 8.Washer 2

9. Instruction *1

FAILURE AND TROUBLESHOOTING

Failure Appearance	Possible Reasons	Troubleshooting
This first time downward-press iron cover and not absorbed into up mold	1.

Unsuitable operating method

2. Too much lubricating oil in the up mold

| 1. The first time downward press-up mold hinge is in a separate state

2. Use a clean cloth or tissue to completely wipe it if found too much lubricating oil on the mold

3. The up-and-down mold must be on

the same vertical line when closing

The second downward press part is not wrapped in| 1. Unsuitable operating method

2. Unsuitable paper thickness

3. Up mold screws loosen

| 1. The up-and-down mold must be on the same vertical line when closing

2. Use the stipulated thickness of paper

3. Place the up mold on the machine body, and use the complimentary Allen key to fix the screws in the up mold internal hole center.

Not tightly press the badge, pressed in but not firm| 1. The downward press is not in place, not press to the bottom

2. Paper is thinner

3. ( 25mm ) Configured metal back consumables do not place the washer

| 1. Need press to the bottom when downward pressing

2. Change to use a slightly thicker paper

3. Right side mold place 2mm thickness washer when using the metal back consumables

Up mold unable to lift after pressing manufacture, blocked| 1. Up and down mold position deviated

2. The paper is incorrectly cut round or blocked by a foreign object.

| Use a sharp tool (such as a straight screwdriver) to align to the middle merge position clearance which is between up and down mold, and pry open with the object like a hammer (Attention: Just tap it, generally, it will not be too tightened).

Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
Imported to AUS: SIHAO PTY LTD, 1 ROKEVA STREETEASTWOOD NSW 2122 Australia
Imported to the USA: Sanven Technology Ltd., Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
EC REP SHUNSHUN GmbH Römeräcker 9 Z2021,76351 Linkenheim-Hochstetten, Germany
UK REP Pooledas Group Ltd Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom
Technical Support and E-Warranty Certificate www.vevor.com/support

NEED HELP? CONTACT US!