CONNECT TECH CTIM-00151 COM Express Type 7 Carrier Board User Guide
- June 16, 2024
- Connect Tech
Table of Contents
Connect Tech Inc.
Embedded Computing Experts
www.connecttech.com
COM Express® Type 7 Carrier Board
CTIM-00151 COM Express Type 7 Carrier Board
Connect Tech Inc.
42 Arrow Road
Guelph, Ontario
N1K 1S6
www.connecttech.com
CTIM-00151 Revision 0.06 2018-04-12
Document: CTIM-00151
Tel: 519-836-1291
Toll: 800-426-8979 (North America only)
Fax: 519-836-4878
Email: sales@connecttech.com
support@connecttech.com
Preface
Disclaimer
The information contained within this user’s guide, including but not limited
to any product specification, is subject to change without notice.
Connect Tech assumes no liability for any damages incurred directly or
indirectly from any technical or typographical errors or omissions contained
herein or for discrepancies between the product and the user’s guide.
Customer Support Overview
If you experience difficulties after reading the manual and/or using the
product, contact the Connect Tech reseller from which you purchased the
product. In most cases the reseller can help you with product installation and
difficulties.
In the event that the reseller is unable to resolve your problem, our highly
qualified support staff can assist you. Our support section is available 24
hours a day, 7 days a week on our website at:
http://connecttech.com/support/resource-center/. See the contact information
section below for more information on how to contact us directly. Our
technical support is always free.
Contact Information
Mail/Courier
Connect Tech Inc.
Technical Support
42 Arrow Road
Guelph, Ontario
Canada N1K 1S6
Email/Internet
sales@connecttech.com
support@connecttech.com
www.connecttech.com
Note:
Please go to the Connect Tech Resource Center for product manuals,
installation guides, device drivers, BSPs and technical tips. Submit your
technical support questions to our support engineers.
Telephone/Facsimile
Technical Support representatives are ready to answer your call Monday through
Friday, from 8:30 a.m. to 5:00 p.m. Eastern Standard Time. Our numbers for
calls are:
Toll Free: 800-426-8979 (North America
only)
Telephone: 519-836-1291 (Live
assistance available 8:30 a.m. to 5:00 p.m. EST,
Monday to Friday)
Facsimile: 519-836-4878 (on-line 24
hours)
Limited Product Warranty
Connect Tech Inc. provides a two-year Warranty for the COM Express® Type 7
Carrier Board. Should this product, in Connect Tech Inc.’s opinion, fail to be
in good working order during the warranty period, Connect Tech Inc. will, at
its option, repair or replace this product at no charge, provided that the
product has not been subjected to abuse, misuse, accident, disaster or non-
Connect Tech Inc. authorized modification or repair.
You may obtain warranty service by delivering this product to an authorized
Connect Tech Inc. business partner or to Connect Tech Inc. along with proof of
purchase. Product returned to Connect Tech Inc. must be pre-authorized by
Connect Tech Inc. with an RMA (Return Material Authorization) number marked on
the outside of the package and sent prepaid, insured and packaged for safe
shipment. Connect Tech Inc. will return this product by prepaid ground
shipment service.
The Connect Tech Inc. Limited Warranty is only valid over the serviceable life
of the product. This is defined as the period during which all components are
available. Should the product prove to be irreparable, Connect Tech Inc.
reserves the right to substitute an equivalent product if available or to
retract the Warranty if no replacement is available.
The above warranty is the only warranty authorized by Connect Tech Inc. Under
no circumstances will Connect Tech Inc. be liable in any way for any damages,
including any lost profits, lost savings or other incidental or consequential
damages arising out of the use of, or inability to use, such product.
Copyright Notice
The information contained in this document is subject to change without
notice. Connect Tech Inc. shall not be liable for errors contained herein or
for incidental consequential damages in connection with the furnishing,
performance, or use of this material. This document contains proprietary
information that is protected by copyright. All rights are reserved. No part
of this document may be photocopied, reproduced, or translated to another
language without the prior written consent of Connect Tech, Inc.
Copyright 2017 by Connect Tech, Inc.
Trademark Acknowledgment
Connect Tech, Inc. acknowledges all trademarks, registered trademarks and/or
copyrights referred to in this document as the property of their respective
owners. Not listing all possible trademarks or copyright acknowledgments does
not constitute a lack of acknowledgment to the rightful owners of the
trademarks and copyrights mentioned in this document.
ESD Warning
Electronic components and circuits are sensitive to Electrostatic Discharge (ESD). When handling any circuit board assemblies including Connect Tech COM Express carrier assemblies, it is recommended that ESD safety precautions be observed. ESD safe best practices include, but are not limited to:
- Leaving circuit boards in their antistatic packaging until they are ready to be installed.
- Using a grounded wrist strap when handling circuit boards, at a minimum you should touch a grounded metal object to dissipate any static charge that may be present on you.
- Only handling circuit boards in ESD safe areas, which may include ESD floor and table mats, wrist strap stations and ESD safe lab coats.
- Avoiding handling circuit boards in carpeted areas.
- Try to handle the board by the edges, avoiding contact with components.
Revision History
Revision | Date | Changes |
---|---|---|
0 | 3/13/2017 | Preliminary Release |
0.01 | 3/14/2017 | Add Appendix |
0.02 | 3/17/2017 | Update cable kit |
0.03 | 4/17/2017 | Add detailed features |
0.04 | 5/19/2017 | Update installation notes, and 3rd party equipment list |
0.05 | 7/11/2017 | Added cable drawing links |
0.06 | 4/12/2018 | Updated Serial/GPIO P8 |
Introduction
Connect Tech’s COM Express® Type 7 Carrier Board is based on the PICMG COM Express® COM.0 R3.0 specification. It includes 2x 10G ethernet from SFP+ modules, 2x Gigabit Ethernet ports, M.2 NVMe Storage, 4x USB 3.0, full and half size Mini PCIe expansion slots, 8x 3.3V buffered GPIO, and a Console connection via Micro USB.
The carrier board is ideal for high-compute, enterprise level applications that have a need for a small form factor rugged solution providing access to high-end Xeon D class processors.
Connect Tech’s COM Express® Type 7 Carrier Board is based on the PICMG COM Express® COM.0 R3.0 specification. It includes 2x 10G ethernet from SFP+ modules, 2x Gigabit Ethernet ports, M.2 NVMe Storage, 4x USB 3.0, full and half size Mini PCIe expansion slots, 8x 3.3V buffered GPIO, and a Console connection via Micro USB.
The carrier board is ideal for high-compute, enterprise level applications that have a need for a small form factor rugged solution providing access to high-end Xeon D class processors.
Product Features and Specifications
Specifications
Compatibility| COM Express Type 7 Modules PICMG COM Express® COM.0 R3.0
Support for current and next-gen Xeon-D (Broadwell DE) processor modules
Network| 2 x 10GbE (via SFP+ cages)
Integrated 10Gbps PHY located directly on the carrier board
Capable of 10GBASE-SR, 10GBASE-LR or 10GBASE-T using when using the
appropriate SFP+ transceiver module.
2 x GBE Ports (via RJ-45) 1000BASE-T (10/100/1000Mbps) Capable
Storage| 1 x M.2 2280 M-Key Slot (Dual function PCIe + SATA)
– NVMe (PCIe x4 Gen3) Capable
– SATA III (6Gbps) Capable
1 x Standard SATA Port (7-Pin)
USB| 4x USB 3.0 ports
Mini PCIe Expansion| 1x mini PCIe slot full size (USB + PCIe) 1x mini PCIe
slot half size (USB + PCIe)
Serial| 1x CPU Console UART (via Micro USB)
1x General Purpose UART (via 2mm header)
GPIO| 8x 3.3V buffered GPIO
Display| Not directly supported, possible through Mini PCIe expansion
Audio| Not directly supported, possible through Mini PCIe expansion
Misc External Interfaces| Reset Button, Power Button, Sys Ctrl
Power| +12V DC only
RTC Battery| Available through header
Dimensions| 125mm x 95mm (4.921” x 3.74”)
3D model: http://www.connecttech.com/ftp/3d_models/CCG070_3D_MODEL.zip
Operating Temperature| -40°C to +85°C
Part Numbers / Ordering Information
Part Number
CCG070| Base model
Product Overview
Block Diagram
Connector Locations
Top View
Bottom View
Jumper and Connector Summary
Designator | Description |
---|---|
P1 | 10/100/1000 Ethernet |
P2 | Dual SFP+ |
P3 | 10/100/1000 Ethernet |
P4 | M.2 |
P5 | SATA |
P6, | RTC Battery |
P7 | Micro USB Console |
P8 | Misc. I/O |
P9 | CPU Fan |
P10 | COM Express |
P11 | Input Power |
P13A, P13B | Mini PCIe |
P15A, P15B | USB 3.0 |
J1 | NVMe selection |
S1 | Power Selection |
Detailed Feature Description
Preface: This section includes pinouts for all non-standard connectors. For all industry standard connectors; the user will need to refer to the appropriate specification provided by the governing body.
COM Express Module Connector
The processor and chipset are implemented on the COM Express Type 7 CPU
module, which connects to the COM Express carrier via a Tyco fine pitch
stacking connector. 8mm standoffs are required to mount COM Express module.
The following table describe how each of Type-7 module interfaces are used and
allocated to the carrier resources.
Function| COM Express interface|
---|---|---
Location| P10
Type| Tyco 3-5353652-6
Pinout| Refer to PICMG COM Express 3.0
COM Express Interface Usage and Allocation
Module Interface| Carrier Endpoint| Connection Type|
Circuitry Involved
---|---|---|---
10G KR0| P2| Dual SFP+| KR-SFP PHY
10G KR1| P2| Dual SFP+| KR-SFP PHY
10G KR2| N/A| not used|
10G KR3| N/A| not used|
GBE0| P1| P1 – RJ45|
GPIO (in and out)| not used| not used|
I2C| P8| Header| various
LPC| not used| not used|
NCSI| not used| not used|
PCIe0| P13A| Mini PCIe|
PCIe1| P13B| Mini PCIe|
PCIe2| P3| RJ45| PCIe MAC/PHY
PCIe3-15| not used| not used|
PCIe16-19| P4| M.2| PCIe / SATA mux on 16
PCIe20-31| not used| not used|
SATA0| P5| 7 pin SATA| PCIe / SATA mux
SATA1| P4| M.2|
SER0| P7| Micro USB| USB UART
SER1| P8| Header|
SMB| not used| not used|
SPI| not used| not used|
USB0| P15A| USB 3.0|
USB1| P15A| USB 3.0|
USB2| P15B Top, Bottom| USB 3.0| USB 3.0 Hub
USB3 (2.0 only)| P13A, B| Mini PCIe| USB 2.0 Hub
Network
The carrier provides 4 network interfaces. One 10/100/1000 Ethernet direct
from the COM Express module, one 10/100/1000 ethernet from a PCIe MAC/PHY, and
two SFP+ 10G Ethernet implement use the Type-7 10G BASE KR Interfaces. All
connectors are industry standard RJ-45 pinout and SFP+ pinout
Function| Dual SFP+|
---|---|---
Location| P2
Type| Samtec SFPK-2SL-02-S-TR
Pinout| Refer to Small Form Factor Pluggable SFF-8431
Function| RJ-45|
---|---|---
Location| P1. P3
Type| Pulse JXD0-0001NL
Pinout| Refer to IEEE 802.3
USB
The carrier provides 2x Dual USB3.0 connectors. One connector has USB3.0
directly from the COM Express module. The other connector has USB3.0 supplied
by a Hub. All connectors are industry standard USB3.0 right angle.
Function| USB|
---|---|---
Location| P15A,B
Type| TE 1932355-4
Pinout| Refer to Universal Serial Bus 3.0 Specification
Bus Expansion
One half sized Mini PCIe and One full sized Mini PCIe are provided. These
slots support both a x1 PCIe and USB2.0 connection simultaneously to
facilitate using WIFI / Bluetooth combo cards. Both 3.3V and 1.5V are provided
to each slot.
These slots DO NOT support mSATA modules and DO NOT have support for external SIM cards.
Function| Mini PCIe|
---|---|---
Location| P15A, P15B
Type| TE 1932355-4
Pinout| Refer to PCISIG PCI Express Mini Card Electromechanical Specification
Revision 2.0
Storage
The carrier can either be booted from an external SATA HDD/SDD or through
an onboard M.2 NVMe or M.2 SATA drive.
The M.2 slot can support either a M.2 x4 PCIe based NVMe or SATA based. The carrier board automatically handles the switching, however J1 can be used to forced the selection. (J1 off = PCIe based, on = SATA based)
Function| M.2, Key M|
---|---|---
Location| P4
Type| TE 1-2199230-5
Pinout| Refer to PCISIG PCI Express M.2 Specification
Function| SATA|
---|---|---
Location| P5
Type| Molex 0470804001
Pinout| Refer to SATA-IO Serial ATA
Serial and GPIO
The carrier provides an on-board USB UART which acts as a USB client to an
external USB host; such as a laptop.
This allows the user to view the BIOS or OS over USB, providing the module and
operating system have been configured correctly. This UART is connected to the
SER0 interface of the COM Express module.
Also provided are the SER1 interface (3.3V UART signal levels only), GPIO from
an I2C expander, and a connection to the I2C bus.
The GPIO Expander is XRA1200 at address 0x40 (8 bit address).
Function| Micro USB, USB serial Console|
---|---|---
Location| P7
Type| Molex 47589-0001
Pinout| Refer to Universal Serial Bus 2.0 Specification
Function| Micro USB, USB serial Console|
---|---|---
Location| P8
Type| FCI 98414-G06-20LF
Cable| See Cables and Accessories
Pinout|
Pin| Signal| Pin| Signal
1| PWRBTN# ()| 2| GND
3| SYS_RST# ()| 4| GND
5| I2C_SCL ()| 6| GND
7| I2C_SDA ()| 8| GND
9| GPIO0| 10| GPIO4
11| GPIO1| 12| GPIO5
13| GPIO2| 14| GPIO6
15| GPIO3| 16| GPIO7
17| SER1_TX ()| 18| GND
19| SER1_RX ()| 20| GND
(*) COM Express module signals
Input Power, RTC Battery and Fan
Input power is provided through a two-part terminal connector. The carrier
accepts only a +12V DC input; and uses that to generate all other power rails.
On-board circuitry facilitates an ATX power up scheme, which is controllable through switch S1. The COM Express module’s active cooling solution can be connected to the fan connector P9. The COM Express module’s RTC battery is supplied through connector P6. Users can provide their own RTC battery solution or purchase one provided by Connect Tech.
Function| Input Power|
---|---|---
Location| P11
Type| FCI 20020111-G041A01LF (on board) FCI 20020003-G041B01LF(provided)
Pinout| Pin
1
|
VIN
| Signal
| 2| VIN|
| 3| GND|
| 4| GND|
Function| RTC Battery|
---|---|---
Location| P6
Type| Molex 53047-0310
Cable| See Cables and Accessories
Pinout|
Function| CPU Fan, standard 4 pin|
---|---|---
Location| P9
Type| Molex 22232041
| |
Pinout| Pin| Signal
| 1| PWM
| 2| TACH
| 3| +12VV
| 4| GND
Function| Power Selection|
---|---|---
Location| S1
Type| 2x 2 position switch
Pinout|
Switch| State| Function
1| Off (up)| 12V controlled by SUS_S3#
1| On (down)| 12V always on (Bypass)
2| Off (up)| Manual Power Button
2| On (down)| Auto Power Button
Both switches Off will produce an ATX style power up sequence.
RTC Battery
This carrier has a connector P6 providing 3.3V to VBAT, which is the supply
for the RTC Clock of the COM Express module.
For further information about RTC battery selection and life time estimation,
see Application Note 00009
CTIN-00009 http://connecttech.com/pdf/CTIN-00009.pdf
Typical Hardware Installation for +12V power input
-
Ensure all external system power supplies are off.
-
Install the COM Express module into P10. Be sure to follow the manufacturer’s direction for proper heatsink/heat spreader installation and any other cooling instructions from the manufacturer. If active cooling is used plug the 4pin fan connector into P9.
-
Install the necessary cables for the application. For the relevant cables, see the Cables & Interconnect section of this manual. Minimum recommended connections:
• Micro USB for COM Express console redirection into P7
• RTC Battery cable into P6 -
Connect the power cable to power supply
-
Set up console redirection
• Plug the host end of the Micro USB cable into desktop or laptop system.
• Assuming a Windows based system, a FTDI serial driver will install. The USB serial circuit is isolated from the rest of the CCG070 carrier and powered from the cable.
• Run a terminal emulator such as PUTTY, and connect to COM## at 115200 kbps 8N1 (8 bit, 1 stop, no parity). Consult with the module vendor’s documentation to confirm these settings.
NOTE: not all Type-7 modules have console re-direction enabled by default. Consult the module vendor’s documentation for further details. -
For an initial installation & first time power up:
• Set the S1 into +12V always on mode (bypass mode) and manual power button.
• Switch on the power supply – for the very first boot after installing a module into a new carrier a power cycle may be required.
Cables and Accessories
Available from Connect Tech
Drawing No. | Part No. | Description | CKG043 |
---|---|---|---|
CTIC-00435 | CBG116 | ||
System-Misc to 20-pin Minitek Cable | 1 | ||
CTIC-00477 | CBG136 | ||
RTC Battery Cable | 1 | ||
OEM | CBG247 | Micro USB Cable | 1 |
CKG043 Cable Kit also available.
Useful Third Party Hardware and Accessories
Assembly Hardware
Manufacturer | Part No. | Description | Qty | Purpose |
---|---|---|---|---|
McMaster-Carr | 94669A100 | 6mm | ||
unthreaded spacer, M2.5, AL | 4 | Mini PCIe install | ||
McMaster-Carr | 92000A107 | 12 mm Philips | ||
Pan Head M2.5 Screw SS | 4 | Mini PCIe install | ||
McMaster-Carr | 92000A114 | 5 mm Philips | ||
Pan Head M3 Screw SS | 1 | M.2 install | ||
McMaster-Carr | 94669A615 | |||
Or 94669A102 | 8mm unthreaded spacer, | |||
M2.5, AL | 5 | COM Express module install * | ||
McMaster-Carr | 91828A113 | 2mm nut, M2.5 | ||
SS | 5 | COM Express module install * | ||
McMaster-Carr | 92000A112 | |||
to 92005A079 | 25 mm Philips Pan Head |
M2.5 Screw
30 mm Philips Pan Head M2.5 Screw| 5| COM Express module install *
(*) Hardware required will depend on the vendor’s cooling solution
Cables and Modules
Manufacturer | Part No. | Type | Description |
---|---|---|---|
Innodisk | EMPV-1201-W1 | Mini PCIe | Mini PCIe to dual VGA & HDMI(DVI-D Single |
Link) module
Innodisk| 7W9000000080| Cable| Dual VGA Cable for above
Innodisk| 7W9000000020| Cable| HDMI Cable for above
Avago| AFBVR-2CAR10Z| SFP+ Cable| 10G Ethernet SFP+ Active Optical Cable
Intel| SSDSCKJW180H601| M.2 SSD| SSD 180GB 80mm SATA 6Gb/s, 16nm, MLC
Samsung| MZ-V6E250| M.2 SSD| SSD 250GB PCIe 3.0 x4, NVMe 1.2
Document: CTIM-00151
Revision: 0.06
Date: 2018-04-12
Connect Tech Inc.800-426-8979 |
519-836-1291
References
- CKG043 - Connect Tech Inc.
- Support - Connect Tech Inc.
- Resource Center - Connect Tech Inc.
- Connect Tech Inc., Embedded Computing Experts
- McMaster-Carr
- McMaster-Carr
- McMaster-Carr
- McMaster-Carr
- McMaster-Carr
- McMaster-Carr
- McMaster-Carr
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>