FK technics TGR-12V-20W Long Life LED Driver 12V DC Instructions

FK technics TGR-12V-20W Long Life LED Driver 12V DC

Product Specifications:

Code| Input V AC| V DC| Output W| A| POWER IP Coverage| DIMENSIONS L x W x H (mm)
---|---|---|---|---|---|---
4739954-08| 220-240 V| 12 V| 15 W| 1.25 A| IP20| 90 x 40 x 24

Product Usage Instructions

Use:

The sources are designed to supply consumers with low DC voltage, suitable for applications with LEDs, such as LED strips. To ensure a longer service life, choose a source with approximately 20% reserve capacity.

Maintenance:

The sources are maintenance-free and do not require special upkeep. Simply remove dust by vacuuming and ensure proper airflow for optimal performance.

Output Terminals:

The output terminals are labeled as + and – for both 12V and 24V DC outputs.

Input Terminals:

Connect the input terminals labeled as L (phase) and N (zero) to the appropriate power source.

FAQ

Q: Can I use this product with devices other than LEDs?

A: The product is designed for low DC voltage applications, primarily with LEDs. It is recommended to use it as intended for optimal performance.

Q: What should I do with a non-functional product?

A: Dispose of any non-functional product following applicable environmental protection regulations to ensure proper disposal.

Power supply with covered terminals

Thank you for the trust you have shown by purchasing the FK product technics. This manual will familiarize you with the mentioned product, his functions and proper operation.

IMPORTANT

• Before using the product, read this manual and the safety warning carefully, to prevent possible damage or injury.
• Keep these operating instructions so that you can read them again at any time!
• This user manual is part of the product and contains important instructions to put the product into operation and to operate it.
• If you pass the product on to other people, be sure to hand it over to them and this user manual.
• The content of this manual is bound by copyright laws and without the written consent of the company FK technics, spol. s r.o., its content may not be reproduced.

NOTICE

• Use the device only for the purposes for which it is intended, taking into account its technical characteristics specifications. Its overload or higher voltage can destroy the device.
• Installation of the device may only be carried out by a qualified person according to the valid decree.
• The company FK technics, spol. s.r.o. is not responsible for any damages incurred improper handling of the product.
• Any modifications or other interventions in the design of the source that may be prohibited are prohibited cause non-functioning of resources and possibly cause further damage.
• Therefore, any intervention in the design of the sources voids the warranty.

USE

The sources are designed to supply consumers with low DC voltage. Appropriate are for applications with LEDs, typically LED strips. For a longer service life, choose a source with approx 20% reserve.

CONSTRUCTION

• Before the assembly itself, always make sure that the supply wires are not connected to Tension. Beware of electric shock!
• The connection terminal block of the source is not designed for mechanical stress. At when connecting the wires to the terminals, be sure to use the appropriate force, choose the appropriate size screwdriver and connect only the appropriate cross-section of wires.
• After connecting all the wires, always cover the terminals with caps and screw them. Caps it also serves to limit the pull and prying of the conductor on the terminal board.
• Power sources must be placed or built into applications in such a way that free flow of air around the source was guaranteed and it was spontaneous cooling and the prescribed maximum ambient temperature was observed.
• Overheating of the source may limit the function compared to the built-in protection, impermissible working temperatures mean a noticeable shortening of the service life resources or their possible damage. Do not cover the source! (e.g. insulating cotton wool in soffit)

MAINTENANCE

The sources are designed as maintenance-free and do not require any special maintenance. Removing dust by vacuuming and ensuring air flow is suitable.

DECLARATION OF CONFORMITY
The product complies with all basic valid European standards which can be presented upon request.

DISPOSAL
A non-functional product must be disposed of in accordance with applicable environmental protection regulations!

TECHNICAL PARAMETERS

Code

| INPUT| OUTPUT| POWER| DIMENSIONS
---|---|---|---|---
V AC| V DC| W| A| IP Coverage| L x W x H (mm)
4739954-08| 220-240 V| 12 V| 15 W| 1,25 A| IP20| 90 x 40 x 24
4739955-08| 220-240 V| 24 V| 15 W| 0,625 A| IP20| 90 x 40 x 24
4739956-08| 220-240 V| 12 V| 30 W| 2,5 A| IP20| 147 x 48 x 24
4739957-08| 220-240 V| 24 V| 30 W| 1,25 A| IP20| 147 x 48 x 24
4739958-08| 220-240 V| 12 V| 40 W| 3,33 A| IP20| 160 x 58 x 20
4739959-08| 220-240 V| 24 V| 40 W| 1,67 A| IP20| 160 x 58 x 20
4739960-08| 220-240 V| 12 V| 60 W| 5 A| IP20| 185 x 64 x 22
4739961-08| 220-240 V| 24 V| 60 W| 2,5 A| IP20| 185 x 64 x 22
4739962-08| 220-240 V| 12 V| 80 W| 6,66 A| IP20| 170 x 57 x 32
4739963-08| 220-240 V| 24 V| 80 W| 3,33 A| IP20| 170 x 57 x 32
4739964-08| 220-240 V| 12 V| 100 W| 8,33 A| IP20| 180 x 66 x 32
4739965-08| 220-240 V| 24 V| 100 W| 4,16 A| IP20| 180 x 66 x 32
4739966-08| 220-240 V| 12 V| 150 W| 12,5 A| IP20| 205 x 71 x 35
4739967-08| 220-240 V| 24 V| 150 W| 6,25 A| IP20| 205 x 71 x 35
4739968-08| 220-240 V| 12 V| 200 W| 16,66 A| IP20| 205 x 71 x 35
4739969-08| 220-240 V| 24 V| 200 W| 8,33 A| IP20| 205 x 71 x 35

PRODUCER:

FK technics, spol. sr.o. Hartigova 1883/62 130 00 Praha 3
fkt@fkt.cz
www.fkt.cz

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>