FK technics 4739980-08 DIN Rail Power Supply Instruction Manual

FK technics 4739980-08 DIN Rail Power Supply

Specifications

• Input Voltage: 100-240 V AC
• Output Voltage: 12V or 24V DC
• Output Power: See below
• Output Current: See below
• IP Coverage: IP20
• Dimensions: See below

Product Usage Instructions

• Use
  • The DIN rail power supply is designed to supply consumers with low DC voltage, suitable for applications with LEDs, such as LED strips. It is recommended to choose a power supply with approximately 20% reserve for a longer service life.
• Input Terminals
  • The input terminals are labeled as + and – for both 12V and 24V DC inputs. Additionally, there are input terminals for L (phase) and N (zero) which may vary by model.
• Construction
  • It is important to ensure that the power supply operates within acceptable temperature limits to prevent damage or a shortened lifespan.
• Setting the Output Voltage
  • The power supply comes with a factory-set output voltage that can be fine-tuned using a trimmer, typically within a range of approximately +/- 5%. This adjustment is useful for compensating voltage drops in long output wires.
• Declaration of Conformity
  • The product complies with all basic valid European standards and the declaration of conformity can be provided upon request.
• Disposal
  • A non-functional product should be disposed of per applicable environmental protection regulations.

Technical Parameters

DIN rail power supply 12V

Thank you for the trust you have shown by purchasing the FK product technics. This manual will familiarize you with the mentioned product, his functions, and proper operation.

IMPORTANT

• Before using the product, read this manual and the safety warning carefully, to prevent possible damage or injury.
• Keep these operating instructions so that you can read them again at any time!
• This user manual is part of the product and contains important instructions to put the product into operation and to operate it.
• If you pass the product on to other people, be sure to hand it over to them and this user manual.
• The content of this manual is bound by copyright laws and without the written consent of the company FK Technics, spol. s r.o., its content may not be reproduced.

NOTICE

• Use the device only for the purposes for which it is intended, taking into account its technical characteristics and specifications. Its overload or higher voltage can destroy the device.
• Installation of the device may only be carried out by a qualified person according to the valid decree.
• The company FK technics, spol. s.r.o. is not responsible for any damages incurred from improper handling of the product.
• Any modifications or other interventions in the design of the source that may be prohibited are prohibited causing the non-functioning of resources and possibly causing further damage.
• Therefore, any intervention in the design of the sources voids the warranty.

USE
The sources are designed to supply consumers with low DC voltage. Appropriate are for applications with LEDs, typically LED strips. For a longer service life, choose a source with approx 20% reserve.

CONSTRUCTION

• The power supply is mainly intended for installation in distribution boxes on a DIN rail, for installation in applications or devices where it will be secured against unprofessional or accidental handling, or contact with the power terminals.
• Before assembly, always make sure that the wires are not connected to the mains or any other voltage.
• Power sources must be placed or built into applications in such a way that free flow of air around the source was guaranteed and it was spontaneous cooling and the prescribed maximum ambient temperature was observed.
• Never place so that the holes in the perforated cover are covered!
• If good cooling of the source is not guaranteed, it may overheat and thus limit the function. Inadmissibly high working temperatures mean a noticeable shortening of the lifespan of sources or their possible damage.

SETTING THE OUTPUT VOLTAGE
The power supply has a factory-set output voltage that can, however, be fine- tuned (according to model approx. +/- 5%) using a trimmer. This is suitable, for example, for voltage drops in long lines output wires.

DECLARATION OF CONFORMITY
The product complies with all basic valid European standards which can be presented upon request.

DISPOSAL
A non-functional product must be disposed of under applicable environmental protection regulations!

TECHNICAL PARAMETERS

CODE

| INPUT| OUTPUT| POWER| DIMENSIONS
---|---|---|---|---
V AC| V DC| W| A| IP Coverage| L x W x H (mm)
4739980-08| 100-240 V| 12 V| 24 W| 2 A| IP20| 90 x 35 x 58
4739981-08| 100-240 V| 24 V| 30 W| 1.25 A| IP20| 90 x 35 x 58
4739982-08| 100-240 V| 12 V| 54 W| 4.5 A| IP20| 90 x 52.5 x 58
4739983-08| 100-240 V| 24 V| 60 W| 2.5 A| IP20| 90 x 52.5 x 58
4739984-08| 100-240 V| 12 V| 85.2 W (LPS)| 7.1 A| IP20| 90 x 70 x 58
4739985-08| 100-240 V| 24 V| 92 W (LPS)| 3.83 A| IP20| 90 x 70 x 58

PRODUCER

FK technics, spol. sr.o. Hartigova 1883/62 130 00 Praha 3
fkt@fkt.cz
www.fkt.cz

Frequently Asked Questions

• Q: What are the recommended applications for this DIN rail power supply?
  • A: The power supply is suitable for supplying low DC voltage to consumers, especially for use with LEDs such as LED strips.
• Q: Can the output voltage be adjusted?
  • A: Yes, the output voltage can be fine-tuned using a trimmer, typically within a range of approximately +/- 5%.
• Q: How should I dispose of a non-functional product?
  • A: A non-functional product should be disposed of following applicable environmental protection regulations to ensure proper disposal.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>