ideal lux Net SP1 D29 Suspension Lamp Instruction Manual

ideal lux Net SP1 D29 Suspension Lamp

Product Information

Specifications

• Model: Net SP1 D29
• Power: E27 max 1 x 42W
• Input Voltage: 220-240V, 50/60Hz
• Color Options: BIANCO, NERO, ORO
• Manufacturer: IDEAL LUX s.r.l.
• Made in: Italy

Product Usage Instructions

Installation

• Installation must be carried out by qualified electricians by the provided assembly instructions.
• Ensure the main power is switched off before installation.

Safety Instructions

• Always disconnect the power supply before performing any installation or maintenance.
• Use appropriate fixing accessories for different materials. Only use screws and plugs compliant with regulations.
• Do not look directly at the light source.
• Ensure all external damaged electrical cables are replaced by the manufacturer, retailer, or a qualified electrician.
• The fixture may have hot parts. Handle with care.

Electrical Safety Classes

• Class I: Mandatory grounding for electrical safety.
• Class II: Double insulation or reinforced insulation, no grounding required.
• Class III: Low voltage operation (below 50 Volts), no grounding required.

FAQ

• Q: Can the LED light source be replaced?
• A: The LED light source in this product is non-replaceable. Do not disassemble the fixture.
• Q: What should I do if the lamp does not turn on?
• A: If the lamp fails to light up, replace the fuse in the fixture.

Net SP1 D29

• Suspension lamp
• E27 max 1 x 42W / 220~240V – 50/60Hz
  • 8021696328102 BIANCO
  • 8021696313788 NERO
  • 8021696313771 ORO

DIMENSIONS

FEATURES

POWER

INSTALLATION INSTRUCTIONS

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION. THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.

SAFETY INSTRUCTIONS

1. This fitting is produced and tested by the strictest European safety standards (EN 60.598- 1).
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
5. Always isolate power before commencing installation, maintenance or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors.
10. Luminaires are not suitable for recessed on normally flammable surfaces.
11. Luminaire is not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing the ceiling.
13. This fitting is only suitable for fixing the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
15. Only use lamps that do not exceed the maximum specified wattage.
16. Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
18. Cracked or broken safety glass has to be replaced immediately. Use only manufacturer approved parts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected to the metal frame of the lamp. Earthing is obligatory.
22. Class Il Electrical safety is guaranteed by the main insulation and double or reinforced insulation. Earthing is not necessary.
23. Class Ill Electrical safety is guaranteed by the very low power supply (less than 50 Volt). Earthing excluded.
24. Not protected.
25. Protected against solid objects greater than 50 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against solid objects greater than 2,5 mm.
28. Protected against solid objects greater than 1mm.
29. Dust protected.
30. Protected against dust infiltration.
31. Not protected.
32. Protected against vertically falling water drops.
33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.
34. Protected against rain.
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged immersion.
40. The luminaire was not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.

CONTACT

IDEAL LUX s.r.l.

• Via Taglio Destro 32
• 30035 Mirano (VE) Italy
• www.ideal-lux.com.

IDEAL LUX Warehouse

• Via delle Industrie, 8/D
• 30036 Santa Maria di Sala (Venezia)
• 8.00 – 12.00 / 13.30 – 17.00

References

• The domain name Electrician.LA is for sale

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>