ideal lux D75 Zig Zag AP Wall Lamp Instruction Manual
- June 1, 2024
- ideal lux
Table of Contents
ideal lux D75 Zig Zag AP Wall Lamp
Product Information
- Specifications
- Brand: Zig Zag
- Model: AP D75
- Power: LED 30W
- Input Voltage: 220-240V, 50/60Hz
- Available Colors and Temperatures:
- BIANCO 3000 K – 8021696277219
- BIANCO 4000 K – 8021696277257
- CROMO 3000 K – 8021696307183
- NERO 3000 K – 8021696277226
- OTTONE 3000 K – 8021696287072
- RAME 3000 K – 8021696307190
- Manufacturer: IDEAL LUX srl
- Country of Origin: Italy
Product Usage Instructions
- Installation
- The lighting fixture should be installed by a qualified electrician following the assembly instructions provided.
- Light Source
- The product is equipped with a replaceable light source with an efficiency energy class of E.
- LED Information
- The LED light source operates at 88V DC and 300 mA. It is replaceable by the end-user.
- Safety Instructions
- Ensure compliance with European safety standards EN 60 598-1. Installation must be done by a qualified electrician. In case of damage to the external power cable, it should be replaced by the manufacturer only.
FAQs
- Q: Can the LED light source be replaced by the end-user?
- A: Yes, the LED light source is replaceable by the end-user as it operates at safe voltages.
- Q: What are the available colours and temperatures for this product?
- A: The available colors and temperatures are BIANCO 3000 K, BIANCO 4000 K, CROMO 3000 K, NERO 3000 K, OTTONE 3000 K, and RAME 3000 K.
- Q: Where should I contact for technical support?
- A: For technical support and inquiries, you can contact IDEAL LUX srl via their website or visit their warehouse during working hours.
DIMENSION
FEATURE
ASSEMBLY INSTRUCTIONS
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
ICONE
- This product is provided with a light source with efficient energy class of:
- Replaceable light source by an end-user.
- Replaceable LED light source by an end-user.
- Replaceable light source by authorized personnel only.
- Upon the end of the life of the light source, the whole product will be replaced.
- Replaceable control gear by an end-user.
- Replaceable light source by authorized personnel only.
- Upon the end of the life of the control gear, the whole product will be replaced.
SAFETY INSTRUCTIONS
- This fitting is produced and tested by the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires are not suitable for recessed on normally flammable surfaces.
- Luminaire is not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing the ceiling.
- This fitting is only suitable for fixing the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps that do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
- Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected to the metal frame of the lamp. Earthing is obligatory.
- Class IL electrical safety is guaranteed by the main insulation and double or reinforced insulation. Earthing is not necessary.
- Class Ill Electrical safety is guaranteed by a very low power supply (less than 50 Volts). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire is not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
CONTACT
- IDEAL LUX s.r.l.
- Via Taglio Destro 32
- 30035 Mirano (VE) Italy
- www.ideal-lux.com.
- IDEAL LUX Warehouse
- Via delle Industrie, 8/D
- 30036 Santa Maria di Sala (Venezia)
- 8.00 – 12.00 / 13.30 – 17.00
- REV 23/10/2023
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>