ideal lux Walky-2 FI LED Recessed Light Instruction Manual
- June 1, 2024
- ideal lux
Table of Contents
ideal lux Walky-2 FI LED Recessed Light
Product Information
- Specifications
- Model: Walky-2 FI
- Power: LED 1W / 220~240V 50Hz
- Barcode: 8021696249827
- Colour: BIANCO
- Dimensions: 83×168 mm
- Light Source Efficiency Class: WALKY
- Light Source Current: 350 mA
- Light Source Voltage: 3 V DC
Product Usage Instructions
- Installation
- The lighting fitting should be installed by a qualified electrician.
- Follow the assembly instructions by reading the numerical progression provided.
- Light Source Replacement
- This product is equipped with a light source that can be replaced by the end-user. Ensure to follow safety guidelines when replacing the light source.
- Maintenance and Safety Instructions
- Always disconnect the power supply before installation or maintenance.
- Avoid looking directly at the light source.
- Refer to European safety standards EN 60 598-1 for safety compliance.
- For damaged external cables, replacement should be done by the manufacturer, retailer, or a qualified electrician.
- Use appropriate fixtures and accessories for installation, ensuring compliance with regulations.
FAQs
- Q: Can the LED light source be replaced by the user?
- A: Yes, the LED light source is replaceable by the end-user. Refer to the user manual for detailed instructions on how to replace the light source.
- Q: What should I do if the external cable is damaged?
- A: In case of damaged external cables, they should be replaced only by the manufacturer, retailer, or a qualified electrician to ensure safety.
DIMENSION
FEATURE
ASSEMBLY INSTRUCTIONS
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
ICONE
- This product is provided with a light source with efficient energy class of:
- EAN
- 8021696249827
- Light Source Model
- WALKY
- Light Source (mA)
- 350 mA
- Light Source (V)
- 3 V DC
- Replaceable light source by an end-user.
- Replaceable LED light source by an end-user.
- Replaceable light source by authorized personnel only.
- Upon the end of the life of the light source, the whole product will be replaced.
- Replaceable control gear by an end-user.
- Replaceable light source by authorized personnel only.
- Upon the end of the life of the control gear, the whole product will be replaced.
SAFETY INSTRUCTIONS
- This fitting is produced and tested by the strictest European safety standards (EN 60.598- 1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires are not suitable for recessed on normally flammable surfaces.
- Luminaire is not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing the ceiling.
- This fitting is only suitable for fixing the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps that do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
- Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected to the metal frame of the lamp. Earthing is obligatory.
- Class Il Electrical safety is guaranteed by the main insulation and double or reinforced insulation. Earthing is not necessary.
- Class Ill Electrical safety is guaranteed by a very low power supply (less than 50 Volts). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire is not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
CONTACT
- IDEAL LUX s.r.l.
- Via Taglio Destro 32
- 30035 Mirano (VE) Italy
- www.ideal-lux.com.
- IDEAL LUX Warehouse
- Via delle Industrie, 8/D
- 30036 Santa Maria di Sala (Venezia)
- 8.00 – 12.00 / 13.30 – 17.00
- REV 23/10/2023
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>