ideal lux SP12 Nabucco Suspension Lamp Instruction Manual
- June 1, 2024
- ideal lux
Table of Contents
ideal lux SP12 Nabucco Suspension Lamp
Product Information
Product Specifications:
- Model: Nabucco SP12
- Maximum Wattage: E14 max 12 x 40W
- Power Supply: 220-240V, 50/60Hz
- Manufacturer: IDEAL LUX s.r.l.
- Country of Origin: Italy
- Product Code: 8021696237794 ORO
Product Usage Instructions
Installation:
- The lighting fitting should be installed by a qualified electrician.
- Follow the assembly instructions by reading the numerical progression provided.
Safety Instructions:
- Always disconnect the mains voltage before starting the installation or any maintenance.
- Avoid looking directly at the light source.
- Ensure the external electrical cable is replaced only by the manufacturer, retailer, or a qualified electrician if damaged.
- Use appropriate fixing accessories for different materials.
- If the lamp does not turn on, replace the fuse.
- Grounding is mandatory for electrical safety (Class I).
- For Class II and Class III safety, follow the specific guidelines provided.
- Avoid dismantling the LED light source as they are non-replaceable.
Frequently Asked Questions
Q: Can I replace the LED light source in the Nabucco SP12?
A: No, the LED light source in this product is non-replaceable. Do not attempt to dismantle it.
Q: What should I do if the lamp does not turn on?
A: In case the lamp does not turn on, check and replace the fuse if necessary. If the issue persists, consult a qualified electrician.
Q: Is grounding mandatory for this lighting fixture?
A: Yes, grounding is mandatory for electrical safety. Follow the instructions provided for proper installation.
Dimension
E14 max 12 x 40W/220~240V 50/60Hz – 8021696237794 ORO.
Features
Installation Instruction
SAFETY INSTRUCTIONS
- This fitting is produced and tested by the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires are not suitable for recessed on normally flammable surfaces.
- Luminaire is not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing the ceiling.
- This fitting is only suitable for fixing the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps that do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
- Cr the macked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class | Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected to the metal frame of the lamp. Earthing is obligatory.
- Class II Electrical safety is guaranteed by the main insulation and a double or reinforced insulation. Earthing is not necessary.
- Class Ill Electrical safety is guaranteed by a very low power supply (less than 50 Volts). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected
- Protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire is not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
Contact Information
IDEAL LUX s.r.l.
- Via Taglio Destro 32 30035 Mirano (VE) Italy
- www.ideal-lux.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>