ideal lux MAP1 Clio Wall Lamp Instruction Manual
- June 1, 2024
- ideal lux
Table of Contents
ideal lux MAP1 Clio Wall Lamp
Product Information
Specifications:
- Model: Clio MAP1
- Socket: E27
- Maximum Wattage: 1 x 42W
- Voltage: 220-240V
- Frequency: 50/60Hz
Product Usage Instructions
Installation :
The lighting fitting should be installed by a qualified electrician. Follow
the assembly instructions by reading the numerical progression provided.
Safety Instructions:
- Ensure the device complies with European safety standards EN 60 598-1.
- For installation, consult a qualified electrician as per regulations.
- If the external power cable is damaged, it should only be replaced by the manufacturer, retailer, or a qualified electrician.
- Always disconnect the power supply before installation or maintenance.
- The device may have hot parts; handle with care.
- Use appropriate fixing accessories specific to the material; use compliant screws and plugs.
Maintenance and Troubleshooting:
- If the lamp does not turn on, replace the fuse.
- The lamp features a non-replaceable LED light source.
- Different classes of electrical safety are indicated based on grounding requirements and insulation levels.
- Ensure the device is protected against solid particles and dust ingress according to specified levels.
- Refer to the user manual for detailed maintenance instructions.
FAQ
-
Q: What should I do if the lamp does not turn on?
A: Check and replace the fuse if necessary. Ensure the power supply is connected correctly. -
Q: Can I replace the LED light source?
A: No, the LED light source is non-replaceable. Do not attempt to disassemble the lamp. -
Q: Is grounding mandatory for this lamp?
A: Yes, grounding is mandatory for electrical safety. Refer to the safety class indicated for specific requirements.
Clio MAP1
- Wall lamp
- E27 max 1 x 42W / 220~240V 50/60Hz
- 8021696145228 ANTRACITE
- 8021696146775 BIANCO
- 8021696326788 COFFEE
- 8021696146782 GRIGIO
- 8021696146799 NERO
Warning! The diffuser should be head up
ASSEMBLY INSTRUCTIONS
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION THE
LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN 
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE
SAFETY INSTRUCTIONS
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.
- This fitting is produced and tested in accordance with the strictest European safety standards EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires not suitable for recessed on normally flammable surfaces.
- Luminaire not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps which do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
- Cracked or broken safety glass has to be replaced immediately. Use only manufacturer approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class Il Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
- Class III Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Totally protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain. 35. Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
IDEAL LUX s.r.l.
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com
IDEAL LUX Warehouse
Via delle Industrie, 8/D
30036 Santa Maria di Sala (Venezia) 8.00 – 12.00 / 13.30 – 17.00