YAMAN YJMF0-1-001E Blue Green Mask User Manual

YAMAN YJMF0-1-001E Blue Green Mask

User’s Manual
Home-care Beauty Device Blue Green Mask YJMFO

Introduction

Thank you for purchasing a YA-MAN product.

• Do not use the device before reading the Safety Precautions (pages 3-8).
• Please read this User’s Manual carefully for information on how to use the device properly and safely.
• After reading the contents hereof, be sure to keep this User’s Manual in an accessible location.
• Make sure to include this User’s Manual if you are transferring ownership of the device to another person.

Flow Chart of How to Use

Safety Precautions

• Read these Safety Precautions carefully before using the device in order to use it correctly.
• Use the device sensibly in accordance with the prescribed steps.
• Immediately discontinue use and arrange to have the device repaired if any abnormality occurs.
• Do not use the device in a defective state, as doing so could cause a physical harm to the user.
• The precautions listed in the User’s Manual are very important. For your safety, please follow them carefully.
• Precautions are classified as DANGER, WARNING, or ATTENTION in order to clearly specify the level of danger and possible injury or damage that may occur if the device is misused.
• This appliance contains batteries that are non-replaceable.

Classifications of Precautions

• DANGER Improper use of this device poses a severe and likely risk of death or serious injury.
• WARNING Improper use of this device may pose a risk of death or serious injury.
• ATTENTION Improper use of this device may result in an injury or property damage*.

‘Property damage’ refers to damage affecting a dwelling, household belongings, or domestic animals and pets .

Symbols

DANGER (Use and storage)

• The following individuals should not use the device:
  Failure ta comply may cause electronic medical devices to malfunction.

• Do not use the device in con Junction with any medical electronic equipment, including:

  • pacemakers or other implanted electronic medical devices; artificial heart-lung machines or other electronic life-support medical devices; and electrocardiographs or other worn electronic medical devices.
  • This appliance shall not be used by, or on persons up to and including yeas of age.

WARNING (Use and storage)

• Do not use under the following conditions:
  Failure to comply may cause accidents or other problems.

  • If you have existing or suspected heart disease or related disorders · Infants or those who are unable to express their intentions on their own
  • If you are unable to sense temperature or stimulation · If you have on autoimmune disease · If you have a melanoderma · If you suffer from epilepsy
  • If you are photosensitive · If you are using photosensitizers, for example if you are undertaking photodynamic therapy
  • If you suffer from pain in the lower back, neck, joints or areas to which the product is applied · If you have fractured bones

• Consult a physician prior to use under the following conditions:

  • If you have an acute disease · If you have an infectious disease · If you have a malignant tumor · If you have a febrile disease
  • If you have high blood pressure or a blood disease · If you have a fever
  • If you have sensory impairment due to severe peripheral circulatory dysfunction (e.g. diabetes) · If you have a nerve damage
  • If you have a skin disease or atopic dermatitis · If you are a hospital outpatient and are taking medication
  • If you have a pre-existing skin condition, such as an allergic constitution or contact dermatitis, or if you have a concern about your skin when using this device

• Do not use in the following cases or on the following areas,
  Failure to comply may cause accidents or other problems.

  • If your skin is damaged, experiencing a rash, inflammation, or other abnormalities · If you are under the influence of alcohol · Head
  • Anywhere inside the mouth, around the pubic region, or any mucous membrane · Eyeballs · Eyelids (eye sockets) · Bulging moles · Viral warts
  • Areas where you have broken a bone · Areas of internal bleeding, swelling or scabbing after cosmetic medical procedures
  • Avoid using the device for 2 weeks after cosmetic medical procedures. After this period, consult with a physician and only use the device if the physician confirms there is no problem (e.g. Hyaluronic acid injections, silicone injections, botox, thread lifts, double eyelid surgery, HIFU, etc.).

• Do not use the device continuously for an overly long period (for example, through commercial use).

• Do not place the device in water.
  Failure to comply may cause an injury or a failure of the device.

• Do not use the appliance in conjunction with flammable based cosmetic products, unless they are recommended by the manufacturer.

WARNING (Use and storage)

• Do not use the device for any purpose or in areas other than those stated in the User’s Manual. Failure to comply may cause on injury or o failure of the device.

• Do not allow persons who are unable to express their intentions on their own to use the device.

• Da not allow physically challenged persons to use the device unattended.

• Sensory or mental capabilities, or lock of experience and knowledge, unless they hove been given supervision or instruction concerning use of the appliance by o person responsible for their safety.

• Children shall not ploy with the device.

• Cleaning and user maintenance shall not be mode by children without supervision.

• Do not overuse the device.

  • For usage time and frequency, follow the instructions in the User’s Manual.
  • Failure to comply may cause physical injuries.

• Before each use, check the device for any crock, deformation or other damages. Do not use if you simony sign of damage or failure.
  Failure to comply may cause injuries or skin problems .

• Do not use, store, or charge the device in the following locations:

  • In bathrooms or near bathtubs, showers,  washbasins or other containers filled with water
  • Dusty areas
  • Outdoors or o location where there is exposure to direct sunlight
  • Uneven or unstable location, or a location where there is vibration or shocks
  • A location where there are strong radio waves or magnetism
  • Near o flammable substance (such as alcohol, thinner, benzene, nail polish remover or spray).
  • A location where there is exposure to oil smoke or steam
  • A location that may become hot, such as near a heating device (e.g. a heater)
  • A location with drastic temperature changes (far example, near on air conditioner or heater) Failure to comply may cause a fire, electric shacks, accidents, malfunction of the device, falls or injuries.

• Do not leave the device unattended while it is turned on.
  Failure to comply may cause o fire or other accidents.

WARNING (Use and storage)

• Do not use if the power cord is damaged.

• Do not use the device in a dark room. Also, do not look at, or directly into, the irradiation unit. Failure to comply may cause injury to your eyes.

• Do not tighten with excessive force.
  Failure to comply may cause physical pressure, fatigue, and pain.

• Do not use this product when asleep.
  Failure to comply may cause injuries or skin problems.

• Do not disassemble, attempt to repair or modify this device in anyway.

  • Failure to comp y may co use o fire, electric shock or other injuries.
  • Contact your local distributor for an advice on repairing the device.
  • Do not dispose of the device in a fire or place it near fire or flames. Do not use, charge or store in a high-temperature or high-pressure area.
  • The device features a built-in rechargeable battery. Failure to comply may lead to the generation of heat, a fire or explosion.

• When using the equipment in the bathroom, be sure to disconnect the power plug after use, as it is dangerous to access water even when the equipment is turned off.

• If the device is dropped or damaged, turn off the power immediately, pull out the plug, and request a repair/inspection.
  Failure to comply may lead to a fire or electric shock.

• If you feel an earthquake, see lightning or hear thunder, turn off the power and unplug the device.
  Failure to comply may cause a fire or electric shock.

WARNING (Use and storage)

• Do not use together with another electronic device (beauty equipment).
  Failure to comply may cause skin problems or malfunction of the device.

• When using the device, remove all metal accessories (e.g. necklaces)
  Failure to comply may cause skin problems.

• Ensure that the temperature of the usage environment is properly maintained.

• The range of environmental temperature in which the device con be used is from 10 to 40°C. Verify the ambient temperature of the location where the device will be used.

• Failure to comply may cause the device to fail or malfunction.

• The device may not correspond effectively to the ambient temperature of a new location immediately after moving to the new location.

• Do not apply excessive force onto the mask. Applying excessive force, including bending, pulling or folding the face mask or the neck mask, may damage the product or cause it to malfunction.

CAUTION (Use and storage)

• Do not press the device too hard and do not use it continuously.
  Pressing the device stronger than necessary or using it continuously may damage the skin.

• Do not allow the device to come into contact with another beauty device or electronic appliance while the power is on.

• Do not use with other electronic products (electric blankets/bed sheets, heated tables, etc.) at the same time.
  Failure to comply may lead to accidents due to malfunctions.

• Do not use while driving.
  Failure to comply may cause accidents or injuries.

• During the treatment, carefully check that your skin is not showing any abnormalities.

• Stop using the device immediately if you start to feel pain, fatigue or see any skin reaction during use.

• Stop using the device immediately if the treatment does not agree with your skin. If symptoms persist the following day and beyond, consult a physician.

WARNING (The power supply)

• Please DO use the device with an operating voltage range from 100 V to 240 V.

• Make sure the plug is fully inserted into the power outlet.
  Failure to comply may cause a fire, electric shock or a failure of the device.

• If any problem occurs, turn off the power immediately.

• Always use the dedicated AC adapter.
  Failure to comply may cause on electric shock, a short circuit or a fire.

WARNING (when using outside of Japan)

• Be sure to use a 100-240V AC power adapter for charging the device.
  Failure to comply may cause a fire or electric shock.

• Be sure to check the plug configuration and the voltage of the power outlet before use.
  Failure to comply may cause the generation of heat, a fire, or a malfunction of the device.

• The plug configuration and voltage may vary depending on the region and the type of accommodation.
  Always be sure to check for compatibility before using the device.

• For information about plug adopters, consult a consumer electronics retailer.

• This appliance contains batteries that ore only replaceable by skilled persons.

Names and Functions of Components

The design and specifications of the device and attached accessories are subject to change for improvement purposes without notice.

Accessories

• Do not throw away the mask stands (for face mask and neck mask) as they are used to store face masks and neck masks.

  • Mask stand (far face mask)
  • Mask stand (far neck mask)
  • AC adapter
  • User’s Manual

Main Unit (controller)

Main Unit (face mask/neck mask) Functions

Auto Power Off
The device will automatically switch off approx. 10 minutes alter it has been turned on.

Before Use

Charge the Device

• Fully charge the battery before using the device for the first time after purchasing.
• When using the device for the first time or when the device has not been used for an extended period of time, it is possible that you will be able to use the device for a short time only, even with a full charge. In such a case, charge the controllers again before using it.
• Use only the included AC adapter.

Charging| The lamps will turn on in the following order:
SOOTHE FIRM BRIGHT.
---|---
When charging is complete| The SOOTHE, FIRM, and BRIGHT lamps all turn on and then turn off alter 5 seconds.
Charging time| Approx. 6 hours
Operating time| Approx. 40 minutes

• Actual charging time and operating time will differ depending upon the remaining battery level and the charging environment.

How to check battery level

flash 3 times, turn off, and then power off automatically.

ATTENTION

• If there is any water droplet on the controllers or charging terminal, make sure to wipe them dry before use. Charging the device with water droplets on the device could cause a failure.
• When you have not used the device for a long period of time, check to see that it is functioning normally before re-starting use. Failure to comply may cause an accident or a malfunction of the device.

How to Use

When using the device for the first time, always test for compatibility with your skin to prevent skin problems.
If, after using the device for about one minute, you experience no abnormalities on your skin, you can continue using it.

Preparation

1. Wash your face and apply lotion on the skin
2. After washing your face to remove makeup, please use your own skin-care products to prepare your skin for treatment.
3. If your hair is long, we recommend tying it up.
4. Connect the controller Connect the mask to the controller.
5. Do not press any button of the controllers when you attach them to the silicone mask.
6. Make sure the power is switched off when attaching the controllers onto the silicone mask.

ATTENTION

• Do not use skin-care products which contain oil, such as oil-based serums. It may cause deterioration of the mask.
• Refrain from irradiation if you are still wearing makeup (far example, foundation cream). Using the device without removing makeup may cause skin problems.

Putting on (neck mask)

1. Fit the neck mask onto your neck

2. Ensure that your neck is clean. You can also moisturize your skin with your personal skin care products before use.

3. Make sure that no hair strands are caught in the mask.

4. Make sure to attach the cord so that it is facing downward, as shown in the figure above.
   Point
   When wearing the face mask and the neck mask at the same time, we recommend putting on the neck mask first and then the face mask, to prevent the respective cords from getting entangled.

5. Verify that the mask is firmly attached using a mirror

6. Lay stopper band [4] on top of stopper band [3] and fasten while making the necessary adjustments for the mask to tightly.

7. Be careful not to fasten the Stopper band too tight.

8. Even if the mask does not fit perfectly and appears to be loose, as long as the section with the lit LED is in contact with your skin, you can proceed with the treatment.

ATTENTION
The band is made al stretchable silicone rubber and pulling it too hard when fitting the mask an may cause it ta became too tight around the neck. Adjust the band  that it lightly touches the section with the lit LED.

Putting on (face mask)

1. Fit the face mask onto your face 

2. Adjust the mask to positions of your eyes.

3. Make sure that no hair strands are caught in the mask.
   Point
   When wearing the face mask and the neck mask at the same time, we recommend putting on the neck mask first and then the face mask, to prevent the respective cords from getting entangled.

4. Verify that the mask is firmly attached using a mirror.

5. Lay stopper band [2] on top of stopper band [I] and fasten while making the necessary adjustments for the mask to tightly.

6. Be careful not to fasten the Stopper band too tightly.

7. Even if the mask does not fit perfectly and appears to be loose, as long as the section with the lit LED section lightly touches the skin, you can proceed with the treatment.
   Point
   If the mask is too large, tying your hair at the back of your head will help keep the face mask in place. If the mask is too small, you con use your hand to hold it in place without having to fasten the band.

Beginning the treatment (face)

1. Turn on the device
   Long-press the face mode button to light up BRIGHT Mode and start operation.

2. Select the mode
   Each time you briefly press the face mode button on the controller, the mode changes in the following order: BRIGHT FIRM➔ SOOTHE … 

There are no level settings.

• Infrared rays, invisible to the naked eye, ore emitted together with the red LED.

ATTENTION

• Refrain from using the device continuously for more than 10 minutes. Failure to comply may cause skin problems.
• If the light feels too bright during treatment, adjust the fit of the eyecup by changing the position of the mask or how the band is fastened, or continue treatment with your eyes closed. Failure to comply may cause injury to your eyes or skin.

Turn off the device

• The device will automatically switch off approx. 10 minutes after it has been turned on.
• If you wish to stop in mid-treatment, long-press the FACE Mode button on the controller to turn off the power.
• After each use, refer to ‘After Treatment’ (page 18) and remove the remaining sebum, lotion and other particles stuck to the device.
• Failing to remove them may cause a malfunction of the device or skin problems.

Beginning the treatment (neck)

1. Turn on the device
   Long-press the NECK Mode button to turn on BRIGHT & FIRM mode and start operation.

2. Turn off the device

3. The device will automatically switch off approx. 10 minutes after it has been turned on.

4. If you wish to stop mid-treatment, long-press the NECK Mode button on the controller to turn off the power.

5. • After each use, refer to ‘After Treatment’ (page 18) and remove the remaining sebum, lotion and other particles stuck to the device.
     Failing to remove them may cause a malfunction of the device or skin problems.

There ore no level settings.

Mode LED color
BRIGHT & FIRM Blue green+ red

After Treatment How To Clean

Wipe face mask, neck mask and controller after each time to keep them clean.

1. Wipe off any dirt using a well-wrung soft cloth or similar materials.
2. For stubborn steins, wipe gently with a cloth soaked in a diluted neutral detergent.
3. Do not leave the device with remaining sebum or lotion on it.
4. Place the device (face mask and neck mask) on the stand
   To prevent the masks from losing its shape, please store them pieced on the stand provided.

• When cleaning the device, be sure to turn off the device. Failure to comply may cause an electric shock, short circuit or fire.
• Do not wash it with water.
• This device is not waterproof. Doing so may cause a failure of the device.

ATTENTION
Never use alkaline detergent, alcohol, thinner, or nail polish remover to clean the device.

Storage

• Store in a clean, well-ventilated place out of the reach of children.
• If you do not plan on using the device for a long time, disconnect the face mask and neck mask cords and the AC adapter from the controller, and unplug the AC adapter from the outlet before storing.
• Do not leave the device in hot or humid places, such as near flames, in bright sunlight or in a bathroom.
• When storing, do not fold the mask.

Maintenance and Inspections

• If you have not used the device for an extended period, inspect it carefully and check that the device works properly and safely before use.
• If the device is malfunctioning, go to ‘Troubleshooting’ (page 20) and attempt to identify the problem before arranging to have the device repaired. If the problem persists, contact your local distributor.
• If the device malfunctions or appears damaged, please contact your local distributor.

Additional Information

Troubleshooting
If you perceive any abnormality with the device during use, check to see whether any of the following symptoms are present.

The device does not turn on| •   Press either the face button or neck button for longer than 1 second (pages 15and 17).
---|---
•    The device has run out of power. Charge the battery (page 11).
Device only operates for a few minutes even after charging.| •   The device will automatically switch off approx . 10 minutes after it has been turned on .
---|---
•   Low battery. Charge the battery (page 11).
•    The battery has expired. Consult the Global After Service ( https://www .ya-man.co.jp/en/support/repair/ ) or your local distributor.
•   The battery does not charge properly. Check that the mode display LED turns on and that charging has started.

• The mode display LED on the controller flashes during operation.
  Low battery. Charge the battery (page 11).

• The device does not start charging.

  • Connect the AC adapter to a power outlet (page 11).
  • Attach the AC adapter to the controller body (page 11).

• An electronic sound can be heard during operation.
  This is a normal operating sound. This is not a malfunction.

Frequently Asked Questions

• What is the recommended duration and frequency of use?
  Use the device on the same area for about 10 minutes once a day. For the face, select one of the available modes.

  • The device will automatically switch off approx. 10 minutes after it has been turned on.
  • The above information is a guideline only. Please observe your skin condition and use the device accordingly.
  • Check carefully to make sure that there are no skin abnormalities before using the device.
  • Stop using the device immediately if the treatment does not agree with your skin.

• Can I use the face mask and the neck mask separately?
  They can be used together or separately.

• Can I use the device continuously?
  We recommend using this device once a day for 10 minutes. If you use the same mask consecutively, leave an interval of at least 30 minutes.

• Can I use the device in the bathroom?
  This device is not waterproof. Do not use the device in the bathroom.

• Can I use the device while sleeping?
  Do not use the device while sleeping.

• Can I use the device on dry skin?
  Yes.

• Can I use the device over a facial mask?
  No.

• My skin is experiencing a rash/inflammation/itchiness
  This is caused by heat and light stimulation. If symptoms persist the following day and beyond, consult a physician.

• I’m concerned about the smell of the mask
  Silicone rubber may sometimes produce a peculiar smell, but this should not be considered a sign of malfunctioning.

• I feel some discomfort and tiredness
  This is caused by heat and light stimulation. Stop using the device until your foci al discomfort is gone.

• My teeth hurt when I use the device
  If you ore undergoing dental treatment, the pressure of the mask may cause tooth pain. If you feel discomfort, consult a physician.

• Can I use the device immediately after sun tanning?
  Using the device after sun tanning or shaving may cause inflammation.
  If skin problems should occur while using the device, stop using the device immediately and consult a physician.

• Q My skin is experiencing redness
  The pressure from the mask may cause temporary redness. If the redness continues the following day, consult a physician.

• The mask leaves a mark on my face
  The mask is made of stretchable silicone. Depending on the condition of your skin, the mask may leave a mark. However, there is no need for concern as the mark will disappear with time.

• Is there a possibility that makeup color will transfer  to the mask?
  Yes, this may occur. Please remove makeup before using the device.

Product specifications

environment.)
Operating time| Approx. 40 minutes (from a fully charged state) * Operating time moyvory with conditions of use.
Outside dimensions| Face mask: Approx. W177, H209, D247 (mm). Length of cord, 75 cm Neckmosk:               Approx. Wl39 x H69 x Dl32 (mm). Length of cord: 71 cm Controller:                approx. W56, H130, D39 (mm)
Weight| Face mask: approx. 458 g; Neck mask: approx. 141 g; Controller: Approx. 196 g
Materials| Face mask and neck masks: silicone and TPU; Controller: ABS
Country of origin| Made in China
Accessories|

• Mask stand (for face mask)                                      One
• Mask stand (for neck mask)                                      One
• AC adapter                                                                  One
• User’s Manual

Recommended environmental temperature| 10°Cto40°C

Contacts for overseas customers
Please contact your local distributor or visit YA-MAN Global websites ( https://www.ya-man.com/en/ ).

Marking Description

• This marking indicates that product should not disposed with other household wastes throughout the UK and EU. To prevent possible home to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.
• To return your used device. please use the return and collection systems contact the retailer where the product was purchased.They can take this product for environmentally safe recycling.
• This marking indicates that the detachable supply unit.
• This product must be charged only using the included detachable power supply.

YJFM0-1-00lE
©2024 YA-MAN All Rights Reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>