Thermogroup Ablaze Mirrors Framed Mirror Range Installation Guide

Thermogroup Ablaze Mirrors Framed Mirror Range

Product Information

• Specifications
  • Product Name: Ablaze Mirrors Framed Mirror Range
  • Installation: Wall-mounted
  • Warranty: 2 years

Product Usage Instructions

• Before Installation
  • Obtain suitable fixing screws and anchors based on the wall type.
  • Measure the distance between the hangers on the mirror and mark your wall using a spirit level.
  • Drill holes in the positions marked and insert suitable wall plugs or anchors.
  • Insert the screw through the slot in the tongue wall hanger and screw it into position. Adjust the mirror up or down for any minor height adjustments or levelling.
  • Lower the mirror onto the hangers on the wall with care.
• Care and Maintenance
  • For best results, clean the mirror with methylated spirits and water at a rate of 30% methylated spirits to 70% water.
  • Avoid using Windex or similar cleaning products.
  • Do not get water on the sides or back of the mirror to prevent damage to the silver backing.
• Warranty Information
  • The Framed Mirror Range comes with a 2-year warranty.
  • To claim the warranty, repair, or service, the customer must provide the purchase invoice/receipt.
  • The warranty covers faults and problems developed from manufacturer errors.
  • Damage caused by improper use, carelessness, or incorrect wiring is not covered.
• Safety Information
  • Thermogroup is not responsible for any monetary loss or injuries caused by improper use of this product.

FAQs

• Q: Can I use any cleaning products to clean the mirror?
  • A: It is recommended to clean the mirror with methylated spirits and water. Avoid using Windex or similar cleaning products as they may damage the mirror’s backing.
• Q: What does the warranty cover?
  • A: The warranty covers faults and problems developed from manufacturer errors. Damage caused by improper use, carelessness, or incorrect wiring is not covered under the warranty.

BEFORE INSTALLATION

• Please remove the mirror from the packaging and check for any damage. If there is any damage do not install the product and arrange for a replacement product.
• It is recommended to have two people present for installation, especially for a large mirror.

Installation Steps

KEY:

1. Wall
2. Wall Plug
3. Tongue Wall Hanger
4. Screws
5. Hanger
6. Mirror

DIMENSION

1. Obtain suitable fixing screws and anchors based on the wall type.
2. Measure the distance between the hangers on the mirror and mark your wall using a spirit level.
3. Drill holes in the positions marked and insert suitable wall plugs or anchors.
4. Insert the screw through the slot in the tongue wall hanger and screw it into position. You can adjust the mirror up or down for any minor height adjustments or levelling of the mirror by loosening the screw and sliding the tongue wall hanger up and down. Once levelled screw in position with a 2nd screw in the hole.
5. Lower the mirror onto the hangers on the wall with care.

The mirrors are provided with metal hanger plates on the back of the mirror for either landscape or portrait mounting. The mirror is designed to hang on the top plates. Please note Not all of the hangers will be used as some hangers are used for alternative orientations.

Care and Maintenance

• For best results clean the mirror with methylated spirits and water at a rate of 30% methylated spirits to 70% water.
• Do not use Windex or similar cleaning products.
• Avoid getting water on the sides or back of the mirror as damage to the silver backing can occur.

Warranty Information

• Thermogroup covers all its products with a satisfaction guarantee.
• In addition, Thermogroup will supply a replacement product where a fault is shown to be caused by manufacture, materials or workmanship providing the goods have been installed correctly and according to installation instructions.
• This guarantee does not include removal, freight or installation costs.
• Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
• You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.
• You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
• The Framed Mirror Range has a 2-year warranty. To claim the warranty, repair or service the customer must provide a purchase invoice/receipt.
• If the product develops a fault within the warranty period due to normal wear and tear, Thermogroup at its discretion will recognise whether it’s a faulty product or not.
• If it is impossible or not economical for the manufacturer to repair the product, the manufacturer will replace the faulty product with a new unit of the same model or if there is no stock available of the same model as the product, the manufacturer will replace the product with a new unit of a similar size.
• No responsibility can be taken for altered dimensions and lining up of existing holes.
• The repair/replacement service offered within the warranty period only covers the faults and problems as developed from the manufacturer’s errors. If the product fails whilst under warranty, the warranty only covers the replacement of the goods.
• Any damage caused by improper use carelessness or incorrect wiring is not covered.
• Thermogroup is not responsible for any monetary loss or injuries caused by improper use of this product.

Contact Us

• Phone: 1300 368 631
• Technical Helpline: 1300 989 464
• sales@thermogroup.com.au.
• www.thermogroup.com.au.
• 1300 368 631
• www.thermogroup.com.au.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>