hidealite 7510493 Hide-a-lite Instruction Manual

: June 1, 2024
: hidealite

Table of Contents

hidealite 7510493 Hide-a-lite
Product Usage Instructions
LEDstrip 24V IP67 RGBW
SAFETY INSTRUCTIONS
Installation & Safety Instructions
Installation
Documents / Resources

hidealite 7510493 Hide-a-lite

hidealite 7510493 Hide-a-lite-product

Specifications

Product: LEDstrip 24V IP67 RGBW
Length: 5m
Max. Length: 6m
LED Color: RGB + 3000K
LEDs per meter: 120pcs
Output max/m: 13.3W
Voltage: DC 24V

Product Usage Instructions

Safety Instructions
Read the instructions carefully before installation and keep them for future reference. The luminaire should be installed by a licensed electrician. Ensure the installation is done following local regulations. Before installation or maintenance, disconnect the power supply.

Installation
Follow the instructions for safe and correct installation. Match the LEDstrip’s power with the drive unit. Make sure the maximum recommended ambient temperature is not exceeded. Use supplied clips for permanent installation. For profiles, use heat-resistant silicone for a durable and sustainable installation. Do not applysilicone directly on the LED chip but along the sides.

FAQ

Q: Can I exceed the maximum length of 6m for the LEDstrip?
A: It is not recommended to exceed the maximum length of 6m to ensure the product’s lifespan and performance.
Q: Can I install the LEDstrip without a licensed electrician?
A: It is advised to have a licensed electrician carry out the installation to ensure safety and compliance with regulations.

LEDstrip 24V IP67 RGBW

$hidealite 7510493 Hide-a-lite $1$$

included

E-nr| Snro| El.nr| GTIN| Length| Max.Length| LED color| LED/m| Output max/m| Voltage DC
---|---|---|---|---|---|---|---|---|---
*7510492| 4158557| 3217616| 7392971150222| 5m| 6m| RGB+3000K| 120pcs| 13,3W| 24V
7510493| 4158558| 3217617| 7392971150239| rm| 6m| RGB+3000K| 120pcs| 13,3W| 24V

hidealite 7

For explanation of symbols see www.hidealite.se

SAFETY INSTRUCTIONS

Read these instructions carefully before commencing installation and retain for future reference. The luminaire should be installed by a licensed electrician and in accordance with local regulations. Make sure that the power is off before installation or maintenance.

Find your Proﬁle

Suitable proﬁles at www.hidealite.com

Installation & Safety Instructions

The installation should be performed by a qualiﬁed electrician.
See the table of technical speciﬁcations and follow the instructions to perform the installation in a safe and correct manner; note the recommendations for maximum lengths.
Make sure that the LEDstrip’s voltage corresponds with that of the drive unit and ensure that the polarity is correct.
When two or more LEDstrips are interconnected, make sure the maximum recommended length is not exceeded. installation and that the LED strips do not overlap to avoid overheating.
It is important that the LED luminaire’s maximum speciﬁed ambient temperature is taken into consideration in order to guarantee its life span, if this is exceeded, the life span can be shortened drastically.
Use the recommended/approved assembly ﬁttings to ensure the lifespan of the LEDstrip.
The LEDstrip must not be switched on when rolled up.
LEDs are sensitive components and must be treated with care and not subjected to mechanical stress.
The ﬂexible LEDstrip must not be bent more than the recommended bending radius.
The LED chip should not be exposed to direct sunlight when switched on.
The self-adhesive tape is provide for easy installation. Use the supplied clips for permanent installation. When installed in the proﬁles (not uplight) recommends heat-resistant silicone for a permanent and sustainable installation. Do not apply silicone directly on the LED chip but along the sides.