hidealite 7509826 LEDstrip 24V IP20 Middle Instruction Manual
- May 15, 2024
- hidealite
Table of Contents
hidealite 7509826 LEDstrip 24V IP20 Middle
Product Specifications:
- Product Name: LEDstrip 24V IP20 Midlum
- Model Numbers:
- 75 098 26* 41 585 17 32 276 77 7392971149509
- 75 098 27 41 585 18 32 276 78 7392971149516
- 75 098 28* 41 585 19 32 276 79 7392971149523
- 75 098 29 41 585 20 32 276 80 7392971149530
- 1,2 75 098 30* 41 585 21 32 276 81 7392971149547
- 75 098 31 41 585 22 32 276 82 7392971149554
- Number of LEDs: 168 pcs per strip
- Power Consumption: 9.6W per strip
- Version: 2023/07
Product Usage Instructions
- Installation:
- Ensure power is switched off before installation.
- Peel off the adhesive backing and carefully place the LED strip in the desired location.
- Connect the strip to a compatible power source following the manufacturer’s instructions.
- Operation:
- Switch on the power source to illuminate the LED strip.
- Use a compatible remote control or switch to adjust brightness and color settings if applicable.
- Maintenance:
- Regularly check for dust accumulation and gently clean with a soft, dry cloth if necessary.
- Avoid exposing the LED strip to moisture or extreme temperatures.
Frequently Asked Questions (FAQ):
Q: Can I cut the LED strip to a shorter length?
A: Yes, you can cut the LED strip at designated cut points to achieve
the desired length. Be sure to follow the cutting instructions provided in the
manual.
Q: Can I connect multiple LED strips together?
A: Yes, you can connect multiple LED strips end-to-end using connectors
or soldering, ensuring the voltage requirements are met.
Q: What is the IP20 rating of the LED strip?
A: The IP20 rating indicates that the LED strip is protected against
solid objects larger than 12.5mm and does not have specific protection against
water ingress.
DIMENSION
SYMBOLS
For explanation of symbols see www.hidealite.se
ACCESSORIES
SAFETY INSTRUCTIONS
Read these instructions carefully before commencing installation and retain for future reference. The luminaire should be installed by a licensed electrician and in accordance with local regulations. Make sure that the power is off before installation or maintenance.
Installation & Safety Instructions
- The installation should be performed by a qualified electrician.
- See the table of technical specifications and follow the instructions to perform the installation in a safe and correct manner; note the recommendations for maximum lengths.
- Make sure that the LEDstrip’s voltage corresponds with that of the drive unit and ensure that the polarity is correct.
- When two or more LEDstrips are interconnected, make sure the maximum recommended length is not exceeded.
- Make sure the power is switched off during in-stallation and that the LE Dstrips do not overlap to avoid overheating.
- It is important that the LED luminaire’s maximum specified ambient temperature is taken into consideration in order to guarantee its life span, if this is exceeded, the lite span can be shortened drastically.
- Use the recommended/approved assembly fittings to ensure the lifespan of the LEDstrip
- The LEDstrip must not be switched on when rolled up.
- LEDs are sensitive components and must be treated with care and not subjected to mechanical stress.
- The flexible LEDstrip must not be bent more than the recommended bending radius.
- The LED chip should not be exposed to direct sunlight when switched on.
- The double-sided adhesive tape is for installing the lights, but may need to be complemented with heat-resistant silicone. When installed in the profiles (not uplight) recommends heat-resistant silicone for a permanent and sustainable installation. Do not apply silicone directly on the LED chip but along the sides.
We reserve the right to change specifications at any time.
Installation
Elektro Elco AB, Tallvägen 5, SE-56435 Bankeryd, Sweden
info@elco.se
www.hidealite.se
www.hidealite.uk
www.hidealite.fi
www.hidealite.no
www.hidealite.dk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>