hidealite 100 LED Strip 24V Rgbw Light Instruction Manual
- May 15, 2024
- hidealite
Table of Contents
hidealite 100 LED Strip 24V Rgbw Light
Product Information
Specifications:
- Product Name : LEDstrip 24V IP20 RGBW
- E-nr : 100 *75 104 86 41 585 51 32 176 10 7392971150161
- Length : 5m
- Color Temperature: RGB + 3000K
- LED Quantity : 120 pcs
- Power: 17.6W
- Version : 2023/11
Product Usage Instructions
- Installation:
- Ensure the power is off before installation.
- Clean the surface where the LED strip will be applied.
- Peel off the adhesive backing and carefully attach the LED strip to the desired location.
- Connect the power supply to the strip following the manufacturer’s instructions.
- Remote Control:
- Use the provided remote control to change colors and adjust brightness.
- Experiment with different color combinations to create the desired ambiance.
- Maintenance:
- Regularly check for dust or debris on the LED strip and clean it with a soft, dry cloth if necessary.
- Avoid exposing the strip to water or moisture to prevent damage.
FAQ
- Q: How do I change the color of the LED strip?
- A: You can change the color using the provided remote control. Press the color change buttons to cycle through different colors.
- Q: Can I cut the LED strip to a shorter length?
- A: Yes, you can usually cut the LED strip at designated cut points following the manufacturer’s guidelines. Be sure to seal the cut end properly.
- Q: Is the LED strip waterproof?
- A: The LED strip mentioned in the manual is IP20 rated, which means it is suitable for indoor use and not waterproof. Avoid exposure to moisture.
For an explanation of symbols see www.hidealite.se
DIMENSIONS
- Suitable profiles at www.hidealite.com
Installation
SAFETY INSTRUCTIONS
Read these instructions carefully before commencing installation and retain them for future reference. The luminaire should be installed by a licensed electrician and in accordance with local regulations. Make sure that the power is off before installation or maintenance.
Installation & Safety Instructions
- The installation should be performed by a qualified electrician. See the table of technical specifications and follow the instructions to perform the installation safely and correctly: note the recommendations for maximum lengths.
- Make sure that the LEDstrip’s voltage cor- responds with that of the drive unit and ensure that the polarity is correct. When two or more LE Dstrips are interconnected, make sure the maximum recommended length is not exceeded. Make sure the power is switched off during in-stallation and that the LED strips do not overlap to avoid overheating.
- the LED luminaire’s maxi-mum specified ambient temperature must be taken into consideration in order to guarantee its life span, if this is exceeded, the life span can be shortened drastically.
- Use the recommended/approved assembly fittings to ensure the lifespan of the LED strip.
- The LED strip must not be switched on when rolled up.
- LEDs are sensitive components and must be treated with care and not subjected to mechanical stress.
- The flexible LED strip must not be bent more than the recommended bending radius.
- The LED chip should not be exposed to direct sunlight when switched on.
- The double-sided adhesive tape is for installing the lights but may need to be complemented with heat-resistant silicone. When installed in the profiles (not uplight) recommends heat-resistant silicone for a permanent and sustainable installation. Do not apply silicone directly on the LED chip but along the sides.
We reserve the right to change specifications at any time.
Installation
Elektro Elco AB, Tallvägen 5, SE-56435 Bankeryd, Sweden
References
- LED lighting of the highest quality - Hidealite
- Vi udvikler og sælger LED belysning - Hidealite
- LED-belysning, downlights, spotlights och utendørs belysning av topp kvalitet - Hidealite
- Hide-a-lite - LED-belysning & LED-armaturer för ditt projekt! - Hide-a-lite
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>