MelodySusie MS-P-C180F Portable Electric Nail Drill Instruction Manual

MelodySusie MS-P-C180F Portable Electric Nail Drill

Instruction Manual
Thank you for choosing MelodySusie! Please read this instruction manual carefully and keep it in an accessible location so you may refer to it later.

Safety Instructions

READ ALL INSTRUCTIONS BEFORE USING.
To reduce the risk of burns, electrocution, fire or injury to persons. Please read the following safety instructions carefully to avoid potential hazards that could lead to personal injury or device damage.
NOTE: Use an adapter of 5V 2A if the USB cable of the device connects to the adapter. Do not exceed 5V 2A, or the drill will burn out.

Check before Using

1. Check the cord and device before using. Do not use the damaged cord to charge the device. Do not use the device if it is not functioning correctly.
2. Only plug this device into a voltage system that matches the voltage system specified on the device. The use of improper voltage can cause damage to the device and will VOID the warranty.
3. Use the original power cord only.

Note for Battery

1. Fully charge the battery before the first use to ensure optimal performance.
2. Do not overcharge the device or use it when it is charging.
3. Charge the device in a well-ventilated area within the temperature range of 0 C to 40 C.
4. Do not charge the device near any flammable or explosive materials.
5. Do not cover the device with clothes or other materials while it’s charging.
6. Charge and discharge the device once every three months if the device is not used for long periods. Please note that the battery performance may decline over several years under normal conditions.

Note for Using

1. Turn the power off after use.
2. Do not use crooked or damaged nail drill bits, and only replace the bit when the power is off.
3. Adjust the speed gradually, avoiding sudden changes. Immediately stop using the device if there are any unusual movements or noises.
4. Misuse, dropping or excessive force may cause device damage.
5. Individuals under the age of 18 require parental consent and supervision to use this device.
6. Do not operate in wet or moist conditions.
7. Do not touch any rotating part while the device is working.

Maintenance Work

1. Do not disassemble the device. It is dangerous and will VOID the 2 warranty.
2. Do not place the device at approximately or more than 50°C (in a metal box, car, or other hot places). Keep the device dry and keep it away from oil and grease.
3. Store the device in a cool and dry place. Do not store it in a hot or humid environment.
4. Store the power cord properly and keep it away from heated surfaces.
5. Do not dispose of the device in heat or fire.
6. Do not clean the device with harmful chemicals or detergents. Only a dry cloth is allowed for cleaning.

Note for Injury

1. Frequent manicures can also cause damage to your nails.
2. If you need to remove the gel polish from natural nails, try to use nail polish remover pads to avoid damage to the nail bed with the improper operation.
3. Do not use the device if you have open wound on your nails or hands.
4. If you have skin diseases, heat sensitivity, allergic reactions, onychomycosis, or any other condition, consult your doctor and medical professional before using the device.

Contents

• Rechargeable Nail Drill*1
• USB Cord*1
• User Manual*1
• Sanding Bands*56
• Nail Drill Bits*11
• Nail Brush*1

Using the Nail Drill

1. Step 1: Insert the drill bit firmly into the drill head.
2. Step 2: Press the ON/OFF button for 3 seconds to turn on the device.
3. Step 3: Press the +/- button to accelerate or decelerate the rotation speed between 25 speeds. Long Press the +/- button to quickly adjust to the desired gear.
4. Step 4: Press the F/R button twice quickly to switch the rotation direction to forward when the LCD screen shows “F” or reverse when the LCD screen shows “R”.
5. Step 5: Press the Pause/On button to pause the device when needed, then press to run it again.
6. Step 6: Press the ON/OFF button for 3 seconds to turn off the device after polishing. Take out the nail drill bit.

Tips
If the nail drill is accidentally blocked while working, it will automatically stop to protect the motor and restart by short-pressing the Pause/On button once.

Charging

• Only charge the device when the power is off.
• Do not draw out the connecting wire during charging or touch it with wet hands to prevent electrical leakage, shock, or fire hazards.

1. Take out the USB cord and connect one end to the charging port and the other end to a USB power supply.
2. Charge the device when the indicator light turns red. And the device is fully charged when the indicator light stays Green.

Problem and Terms of Settlement

Specifications

Input Voltage Range: 5V/2A

Warranty and Customer Service

6-month limited warranty Apply for an extra 6-month warranty extension by registering on https://www.melodysusie.com/pages/extend-warranty if needed).
If you require any technical support, please contact us.

• Website: www.melodysusie.com
• Email: [email protected]
• Email: [email protected]

www.melodysusie.com

• US Service: [email protected]
• UK Service: [email protected]
• FR Service: [email protected]
• DE Service: [email protected]

Whipple Rd, Union City, CA 94578
AMZLAB GmbH Laubenhof 23,45326 Essen, Germany THEMIS AR support Itd. 85 Great Portland St, London, United Kingdom, W1W 7LT

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>