melodysusie B07Q8SM65P Eos 3 LED UV Nail Lamp User Manual
- June 4, 2024
- melodysusie
Table of Contents
melodysusie B07Q8SM65P Eos 3 LED UV Nail Lamp
Thank you for choosing MelodySusie! Please read this user guide carefully and keep it in an accessible location as you may refer to it later.
Items Included
- 1 x Eos 3 LED UV Nail Lamp
- 1 x User Manual
- 1 x AC Power Cord
- Step 1 : Connect the power cord to a secure outlet.
- Step 2 : Put your hands in and the lamp will automatically turn on(1 Ss).
- Step 3: Simply remove your hands when curing, and the lamp will turn off automatically.
- Step 4: Choose a pre-set timer button (15s, 30s, 60s, 90s) as needed. The lamp will run until the preset time has elapsed. \
Malfunctions and Solutions
| Malfunctions | Reasons | Solutions |
|---|---|---|
| The nail lamp does not work well./ The beads do not turn on. | The LED light |
beads or the lamp’s internal circuit is damaged. Please contact
our customer service team
| | for help.
The nail lamp does not work|
A light bead or a group of light beads don’t turn on. The light bead is damaged.
| Please contact MelodySusie customer service team to change to
the new light beads.
well./ The| |
|
beads do not
turn on.
|
The power cord’s AC plug
| Please kindly note the plug
is US plug. If you want to
| is not compatible with| use the nail lamp in other
| outlet.| countries or areas, please
use it with a universal
| | adaptor.
| When pressing the bunon, the lamp doesn’t have any response.| Please check
whether the surface of the button has water or dust. Clean the nail lamp with
a dry cloth.
| | Please adjust the angle of
| The light to your nail| your nail surface to face
| surface is not enough.| the light straightly to
ensure sufficient
| | illumination
The gel nail polish cannot be cured or dried| Insufficient curing time may
result in incomplete curing of your gel nail polish. The curing time
requirements vary from different gel polish brands and colors.| Please try to
extend the curing time appropriately until the nail surface is completely
cured. For best results, avoid moving your hand too much until curing is
complete.
|
Please check whether the light beads of nail lamp are aging.
| Please contact MelodySusie customer service team to change for the new light
beads.
Malfunctions| Reasons| Solutions
---|---|---
The gel nail polish cannot be cured or dried
| Use the incompatible polish, such as regular nail polish, nail lacquer.| Please use LED, UV gel nail polish or use a compatible nail lamp.
The gel polish is a bit tacky after drying.
| Please wipe your nail surface with a gentle cleanser or alcohol prep pads.
Malfunctions| Reasons| Solutions
---|---|---
The nail lamp does not work well. /The
beads do not
|
The power cord’s AC plug is loose or poorly connected.
| Reconnect the power cord and make sure it is properly connected or contact
MelodySusie customer service team to change the power supply.
|
turn on.| The power cord’s AC| Make the power cord’s AC
| output is not properly| output is properly
| connected to the lamp’s| connected to the lamp’s
| AC outlet.| AC outlet.
Important Safety Information
- Please be sure to read the following safety instruction to avoid potential hazards that could result in personal injuries or damage to the device.
- Make sure your outlet supplies correct power voltage to avoid damage to the lamp.
- Please do not unplug the power cord when the machine is working to avoid potential damage to the lamp.
- Do not use the lamp’s top as a nail table, as this can negatively affect the performance.
- If you don’t use the nail lamp for long time, please turn off the power switch and store it properly to extend its lifetime.
- Do not disassemble the device. Doing so could be dangerous and result in voiding warranty conditions. If you require any technical support, contact us at service@melodysusie.com.
- If the device or the power cord is damaged, it should be repaired or replaced by MelodySusie or another authorized professional.
- Children under 18 years old should not use this device without parental consent and supervision.
- Please turn off the device and unplug the power cord before cleaning. Use cloth with neutral detergent to clean the surface of machine.
Specifications
- Input/ Output Voltage Range: AC 100-240V/50-60Hz
- Beads Number: 24
- Material: ABS
- Nail Lamp Size: L220W206H100mm (8.668.11 3.94inches)
- Nail Lamp Weight: 554g (1.221b)
- Color: White
- Email: service@melodysusie.com
- Website: www.melodysusie.com
Warranty and Customer Service
MelodySusie offers a 6-month limited warranty on qualityrelated issues. Please apply for your extra 6-month warranty extension and download the user manual in other languages by registering on www melodysusje com if needed.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>