MELODYSUSIE M-B450 Rechargeable Nail Drill Instruction Manual

MELODYSUSIE M-B450 Rechargeable Nail Drill

Safety Instructions

READ ALL INSTRUCTIONS BEFORE USING

To reduce persons. the risk of bums, electrocution, fire, or injury
Please read the following safety instructions carefully to avoid potential hazards that could lead to personal injury or device damage.

Check before Using

1. Check the power cord before using the device for the first time, and periodically throughout its life. Do not use the device if the cord or plug is damaged, or if the device is not functioning correctly.
2. Only plug this device into a voltage system that matches the voltage system specified on the device or charger. The use of improper voltage can cause damage to the device and will VOID the warranty.
3. Use the original charger only.
   The handpiece of the device is not compatible with other models of nail drill machines from MelodySusle or other brands. Please do not connect the handpiece with other nail drill machines.

Note for Battery

1. Fully charge the battery before the first use to ensure optimal performance.
2. Do not overcharge the device or use it when it is charging.
3. Charge the device in a well-ventilated area within the temperature range of oc to 40″C.
4. Do not charge the device near any flammable or explosive materials.
5. Do not cover the device with clothes or other materials while it’s charging.
6. Charge and discharge the device once every three months if the device is not used for long periods. Please note that the battery performance may decline over several years under nonnal conditions.

Note for Using

1. Do not draw out the connecting wires during use or touch the plug with wet hands to prevent electrical leakage, shock, or fire hazards. Please turn the power off after use.
2. Do not use crooked or damaged nail drill bits, and only replace them when the power is off.
3. Adjust the speed gradually, avoiding sudden changes. Immediately stop using the device If there are any unusual movements or noises.
4. Misuse, dropping, or excessive force may cause device damage.
5. individuals under the age of 18 require parental consent and supervision to use this device. B Do not operate in wet or moist conditions.
6. Do not touch any rotating part while the device Is working.

Maintenance Work

• Do not disassemble the device. It is dangerous and will VOID the warranty.
• Do not place the device at approximately or more than 50 • C (in a metal box, car, or other hot places). Keep the handpiece dry and keep it away from oil and grease.
• Store the device in a cool and dry place. Do not store it in a hot or humid environment.
• Store the power cord properly and keep it away from heated surfaces.
• Do not dispose of the device In heat or fire.
• Do not clean the device with harmful chemicals or detergents. Only a dry cloth is allowed for cleaning.

Note for Injury

• Frequent manicures can also cause damage to your nails.
• If you need to remove the gel polish from natural nails, try to use nail polish remover pads to avoid damage to the nail bed with improper operation.
• Do not use the device if you have open wounds on your nails or hands.
• If you have skin diseases, heat sensitivity, allergic reactions, onychomycosis, or any other condition, consult your doctor and medical professional before using the device.

Contents

• Rechargeable Nail Drill
• Power Supply
• Carbide Drill Bit
• Ceramics Drill Bit
• Handpiece Holder
• Handpiece Seat
• Diamond Cuticle Nail Drill Bits
• User Manual

Using the Nail Drill

1. Connect the handpiece to the handpiece jack.
2. Replace the desired drill bit. Please read and follow the steps for Replacing the Drill Bit.
3. Press the ON/OFF button for seconds to turn on the device.
4. Press the Pause/Run button to run the device.
5. Rotate the speed control knob to accelerate or decelerate the rotation speed of the drill bit.
6. Press the Pause/ ON button to pause the device when needed, then press to run it again.
7. Change the rotation direction of the drill bit on the F/R button if needed.
8. Press the ON/OFF button for seconds to off after polishing. Then rotate the central barrel and take out the drill bit. Place the handpiece in the handpiece holder when not in use.

Replacing the Drill Bit

Originally a blank bar is attached, and you can replace it as you like. Please make sure that the desired bit is suitable for the collet.

• Only change the drill bit when the power is off and the handpiece completely stops.
• Do not move the central barrel during operation.
• Insert the drill bit into the device correctly and rotate the central barrel to the correct position, otherwise high vibration, drill bit stuck, etc. may happen.

1. Turn the central barrel clockwise until hearing a ‘click’ sound, then release and remove the original bit and place the desired bit into the handpiece.
2. Turn the central barrel counterclockwise until hearing a  click sound to lock the drill bit in place.
3. Please distinguish the rotation direction of the bit and collet. Take care of your fingers not to be hurt by the edge of bits.

Charging

1. Take out the adapter and connect It to the DC socket of the nail drill.
2. Connect the power supply with the adapter and insert the main plug into a wall socket.
3. The LCD screen will show the battery charge status.

Specifications

• Input Voltage Range: AC100-240V/50-60Hz, O.BA
• Output Voltage: 24V /1A
• Battery capacity: 2000mAH

Warranty and Customer Service

• 6-month limited warranty
  (Apply for an extra 6-month warranty extension by registering at https://www.melodysusie.com/pages/extend-warranty if needed).
  Note: You can purchase the handpiece separately if needed.

• If you require any technical support, please contact us.
  Website: www.melodysusie.com
  Email: seivice@melodysusie.com
  Email: service.uk@melodysusie.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>