Vivolink VLUSB3EXT100H KVM extender User Manual

: June 1, 2024
: VIVOLINK

Table of Contents

Vivolink VLUSB3EXT100H KVM extender
SAFETY PRECAUTIONS
Product Introduction
Specification
Panel Description
System Connection
Button Control
RS232 Control
Panel Drawing
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Vivolink VLUSB3EXT100H KVM extender

Vivolink-VLUSB3EXT100H-KVM-extender-product

Specifications

Model: VLUSB3EXT100H
Product Name: 100m USB3.2 Gen1 Extender over HDBT
Version: VLUSB3EXT100H_2024V1.0

Safety Precautions

Unpack the equipment carefully and save the original box and packing material for possible future shipment.
Follow basic safety precautions to reduce the risk of fire, electrical shock, and injury to persons.
Do not dismantle the housing or modify the module to avoid electrical shock or burn.
Using supplies or parts not meeting the products’ specifications may cause damage, deterioration, or malfunction.
Refer all servicing to qualified service personnel.
Avoid exposure to rain, moisture, or water to prevent fire or shock hazard.
Avoid putting heavy items on the extension cable to prevent extrusion.
Ensure fine ventilation during installation to avoid damage caused by overheating.
Keep the module away from liquids to prevent spillage that may result in fire, electrical shock, or equipment damage.
Do not twist or pull forcefully on the cable ends to prevent malfunction.
Avoid using liquid or aerosol cleaners for cleaning; always unplug the power before cleaning.
Unplug the power cord when the device is unused for a long period.
Dispose of scrapped devices properly; do not burn or mix with general household waste.

Product Introduction

The VLUSB3EXT100H is a 100m USB 3.2 Gen1 Extender over HDBT. Please read the user manual carefully before using the product. Different models and specifications may vary, so refer to the manual for accurate information.

Preface
Read this user manual carefully before using the product. Pictures shown in this manual are for reference only. Different models and specifications are subject to real product.
This manual is only for operation instruction, please contact the local distributor for maintenance assistance. The functions described in this version were updated till January, 2023. In the constant effort to improve the product, we reserve the right to make functions or parameters changes without notice or obligation. Please refer to the dealers for the latest details.

SAFETY PRECAUTIONS

To ensure the best from the product, please read all instructions carefully before using the device. Save this manual for further reference.

Unpack the equipment carefully and save the original box and packing material for possible future shipment
Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
Do not dismantle the housing or modify the module. It may result in electrical shock or burn.
Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction.
Refer all servicing to qualified service personnel.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
Do not put any heavy items on the extension cable in case of extrusion.
Do not remove the housing of the device as opening or removing housing may expose you to dangerous voltage or other hazards.
Install the device in a place with fine ventilation to avoid damage caused by overheat.
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the module immediately.
Do not twist or pull by force ends of the cable. It can cause malfunction.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
Unplug the power cord when left unused for a long period of time.
Information on disposal for scrapped devices: do not burn or mix with general household waste, please treat them as normal electrical wastes.

$Vivolink-VLUSB3EXT100H-KVM-extender- $2$$

Product Introduction

Thanks for choosing the 100m USB 3.2 Gen1 extender. The extender is designed to transmit USB signal up to 100m distance. VLUSB3EXT100H is the host port of the extender, it contains one Type-B and one Type-C for PC or laptop connect. It also has two local USB-A port with 5V500mA power supply for speakerphone and headset. The extender also supports bi-directional 24V PoC power.
The extender features multiple methods of control. When in the AUTO mode, VLUSB3EXT100H will automatically switch to the first detected host. When the active host is removed, the unit will switch to another host when the host is connected to a PC/Laptop. The unit can be manually controlled by the front panel buttons and RS232 commands.

Features

2×1 USB 3.2 Gen1 switcher;
Support extend USB signal up to 100m;
Support RS232 passthrough/control/upgrade;
Auto/manual switching mode;
Bi-directional 24V PoC power supply.

Package List

1x VLUSB3EXT100H
1x Power Adapter (DC 24V, 1.5A)
1x Mounting Kit
1x 3-pin Terminal Block
4x Rubber feet
1x User Manual

Note: Please contact your distributor immediately if any damage or defect in the components is found.

Specification

VLUSB3EXT100H

(The current version only reaches the 70m extension)

Panel Description

Front Panel

$Vivolink-VLUSB3EXT100H-KVM-extender- $3$$

Power LED: The LED illuminates green when the unit is power on.
Select:
- 1/2 LED: The LED illuminates bule when switching to the corresponding host.
- Auto LED: The LED illuminates bule when in auto switching mode and light off when in manual switching mode.
- AUTO/3s: Press button to switch the host. Press and hold the button 3 seconds to switch the switching mode. Note that the factory default switching mode is AUTO.
PoC: 1x DIP switch, turn on/off the PoC.
Devices: 2x Type-A USB 3.2 Gen1, shared 5V500mA total and limit 5V500mA per port. Connecting to the speakerphone and headset.

Rear Panel

$Vivolink-VLUSB3EXT100H-KVM-extender- $4$$

Host: Type-B and Type-C USB 3.2 Gen1, connecting to the PC/Laptop.
RS232: 1x 3-pin DIP switch for select the RS232 port function.
CTRL: Control the unit via sending the RS232 commands.
PASS: RS232 passthrough.
FW: Firmware upgrade.
HDBT-USB3: 1x RJ45 port for connecting with the device unit of the extender.
The yellow light indicates the connection status of the HDBT, and the green LED is the data light.
DC 24V: DC barrel port for DC24V 1.5A power adapter connection.

System Connection

Usage Precaution

Make sure all components and accessories included before installation.
System should be installed in a clean environment with proper temperature and humidity.
All of the power switches, plugs, sockets, and power cords should be insulated and safe.
All devices should be connected before power on.

System Diagram

$Vivolink-VLUSB3EXT100H-KVM-extender- $5$$

Button Control

Manual Switching
When the unit is in the manual switching mode, press the AUTO/3s button repeatedly to cycle through the two hosts, and the corresponding host LED illuminates blue immediately.

Automatic Switching

Press and hold the AUTO/3s button at least three seconds to enable automatic switching. The current host will not be changed, and the auto LED will turn blue.
When in the AUTO mode, the unit will switch according to the following rules:

Press and hold the AUTO/3s button at least three seconds again can exit AUTO mode, but the host will not be changed, and the auto LED will turn off.
New host: Once detecting a new host, the unit will automatically select the new host.
Press the AUTO/3s button also can forcibly change the host.
Reboot: Once power is restored to the unit, it will automatically reconnect the host before powered off.
Source removed: When an active host is removed, the switcher will switch to the other active host.

RS232 Control

Connect the RS232 port to control device (e.g. PC) with RS232 cable. The switcher can be controlled by sending RS232 commands.

RS232 Control Software

Installation: Copy the control software file to the control PC.
Uninstallation: Delete all the control software files in corresponding file path.

Basic Setting

Connect the switcher with all input devices and output devices needed, then to connect it with a PC which is installed with RS232 control software. Double- click the software icon to run this software.

Here takes the software CommWatch.exe as an example:

The main view is shown as below

$Vivolink-VLUSB3EXT100H-KVM-extender- $6$$ Please set the parameters of COM number, baud rate, data bit, stop bit and the parity bit correctly, and then you will be able to send command in command sending area.

RS232 Command

Communication protocol: RS232 Communication Protocol Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none
Note: All commands need to be ended with “”.

System Control

**** Command	Description	Example & CommandFeedback
>Help	Query commands	>Help
>GetStatus	Query status	>GetStatus

<VLUSB3EXT100H<FW Version: V1.0.0a<POC Off<AutoSwitch Mode Off<USB 01<Device Power Follow Host Mode Off<Device1 Power On<Device2 Power On<SetRS232Baud: 9600
>Reboot| Restart the unit| >Reboot
<Reboot
>SetUSB| Switch the local USB-A to HOST[Param1]Param1 = 01,02| >SetUSB 01
<SetUSB 01
>FactoryReset| Factory default the unit| >FactoryReset
---|---|---
<FactoryReset
>SetDeviceFollow [Param1]| Set the devices power mode:Param = On(Follow mode, turn off the power when no host connect)Param = Off(Always on, always provide the power to devices)| >SetDeviceFollow On
<Set Device Power Follow Host Mode On
>GetDeviceFollow| Query devices power mode| >GetDeviceFollow
<Device Power Follow Host Mode On
>SetAutoSwitch| Set the auto switching mode statusParam = On, Off|

SetAutoSwitch On/Off
<SetAutoSwitch On<SetAutoSwitch Off
>GetAutoSwitch| Query auto switching mode status| >GetAutoSwitch
<SetAutoSwitch On
  >SetRS232Baud| Set the baud rate of the unit. Param = 9600(default), 19200, 38400, 57600,115200| >SetRS232Baud 9600
<SetRS232Baud: 9600
  >SetDevicePower [param1] [param2]| Control the devices power supply on/offParam1 = 00~02 00: All devices01~02: Device1~ Device2Param2 = On/Off| SetDevicePower 0 Off
  <Set All Device Power Off
>GetDevicePower|   Query devices power status| >GetDevicePower
<Device1 Power On<Device2 Power On