phrozen 3DJake Wash Cure Kit User Guide
- June 1, 2024
- phrozen
Table of Contents
phrozen 3DJake Wash Cure Kit
Phrozen Wash & Cure Kit Specifications
- Control Mode: Knob + Button
- Rated Power: 48W
- Input: 24 VDC
- Product Dimension: 27.7 x 20.7 x 46.7 cm
- Washing Bucket Volume: 8 L
- Maximum Model Size: 21.8 x 12.3 x 23.5 cm
- Weight: 3.5 kg
- Timer: 0 – 30 minutes
Phrozen Wash & Cure Kit User Guide
01 Before You Start
Place the machine on a clean and level surface. Put the washing basket into the bucket. Ensure you wear protective goggles, gloves, masks, and long- sleeved clothing. Pour the appropriate cleaning fluid into the bucket and cover it during operation to prevent splashing.
02 Instructions
- Preparing Prints:
- If the building plate is smaller than 7, hang it with prints on the cleaning basket using the basket holder.
- If the building plate is larger than 10, place the prints directly into the cleaning basket.
- Cleaning Process:
- Adjust the cleaning time using the knob (not exceeding 30 minutes).
- Lift the basket after the timer stops and remove the prints.
- Dry the prints or use an air gun for quicker drying.
- Ensure complex models are clean; repeat cleaning if necessary.
- After cleaning, proceed to cure the prints.
Note: Regularly replace cleaning fluid for best results. Always follow safety warnings provided in the manual.
Curing Station Specifications
- Acrylic Cover
- Turntable
- Touch Panel
- Cure & Dry Prints
- Display Remaining Time
- Stop Machine
- End Progress & Return to Homepage
01 Before You Start
P lace the curing station on a clean surface, install the turntable, and connect the power. Wear protective goggles and avoid lifting the acrylic cover during operation.
Frequently Asked Questions (FAQ)
- Q: Can I use other cleaning fluids besides alcohol?
- A: Yes, you can use Phrozen Wash or other suitable cleaning fluids as recommended in the manual.
- Q: What should I do if there is residual resin on the prints after cleaning?
- A: Repeat the cleaning process (steps 2-5) to ensure thorough cleaning of the prints.
Washing Station Post Printing Cleaner
Parts
Specifications
- Control Mode: Knob + Button
- Rated Power: 48W
- Input: 24 VDC
- Product Dimension : 27.7 x 20.7 x 46.7 cm
- Washing Bucket Volume: 8 L
- Maximum Model Size : 21.8 x 12.3 x 23.5 cm
- Weight: 3.5 kg
- Timer : 0 – 30 minutes
Before You Start
- Place the machine on a clean and level surface.
- Put the washing basket into the bucket.
- Please make sure to wear protective goggles, gloves, masks, and long-sleeved clothing when handling the machine.
- Pour in an appropriate amount of alcohol (95%) or other cleaning fluid (Phrozen Wash).
- Cover the bucket when the machine is in use to avoid splashing and objects falling.
- Keep the bucket covered to avoid alcohol evaporation when the machine is not in use.
Instructions
- After printing is completed hang the building plate with prints on the cleaning basket (if the building plate is smaller than 7”, use the basket holder). For building plate over 10” put the prints straight into the cleaning basket.
- Turn the knob to adjust the time and press to set. It is recommended that each cleaning time should not exceed 30 seconds as overcleaning might damage the prints.
- After the timer stops, lift the basket vertically and take out the prints.
- Leave prints to dry or use an air gun to accelerate the drying process.
- For hollow and more complicated models, please make sure the prints are clean. If any residual resin was found, repeat steps 2-5.
- After the cleaning process is completed, put prints into the curing machine to cure.
Note: Regularly replace 95% alcohol (cleaning fluid) for optimum results
.
Warning
- Please disconnect the power before cleaning or replacing alcohol (cleaning fluid).
- DO NOT pour resins or other liquid except alcohol (cleaning fluid) into the cleaning bucket. Avoid direct contact with skin to prevent allergies. In case of contact with resin and alcohol (cleaning fluid), please rinse immediately with plenty of water.
- DO NOT remove prints from the bucket when the machine is running. The included power cord set packaged with the main unit cannot be used with electrical equipment other than the specified device
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>