BRESSER 200RF Digital Binocular Night Vision Device Instruction Manual

Art. No. 9677494
Explorer 200RF
Night Vision Device
with Laser Rangefinder
INSTRUCTION MANUAL

200RF Digital Binocular Night Vision Device

About this Manual

Please read the safety instructions and the operating instructions carefully before use.
Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, the instruction manual must be provided to the new owner/user of the  product.

Class 1 Laser Product

This device has been classified as a CLASS 1 LASER product according to EN/IEC 608251-2014.

The accessible laser radiation is safe under reasonably foreseeable conditions, and under normal conditions of use. Do not open the housing. The device does not contain any parts that can be serviced by the end consumer.
Servicing of this unit must be left up to qualified service personnel.

Intended use

This device is designed for viewing at objects in darkness and measuring distances.
General Warning

DANGER!
Children should only use the device under adult supervision. Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard.
Do not expose the device to high temperatures.
Use only the recommended batteries.
Do not short-circuit the device or batteries, or throw them into a fire. Excessive heat or improper handling could trigger a short-circuit, a fire or an explosion.

FIRE RISK!
Do not place the device, particularly the lenses, in direct sunlight. The concentration of light could cause a fire.

RISK of ELECTRIC SHOCK!
This device contains electronic components that operate via a power source (batteries).
Children should only use the device under adult supervision. Only use the device as described in the manual; otherwise, you run the risk of an electric shock.

RISK OF CHEMICAL BURN!
Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with skin, eyes and mucous membranes. In the event of contact, rinse the affected region immediately with a plenty of water and seek medical attention.

NOTE!
Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. Remove the batteries from the unit if it has not been used for a long time.

PRIVACY PROTECTION!
The nightvision device is intended only for private use. Please heed the privacy of other people. Do not use them to look into apartments, for example.

Scope of delivery

Night vision device (A), USB Cable (B), Li-Ion rech. Battery type 18650, (2 pcs., already installed) (C), Neck Strap (D), Carrying Case (E), Cleaning Cloth, Instruction Manual
NOTE : 2 pcs battery are already installed

Parts overview

1.  POWER button
2. MODE button
3. RF button
4. Zoom/Back button
5. Camera/OK button
6. IR button
7. IR button
8. Rangefinder module
9. Objective lens (turn to focus)
10. Infrared (IR) LED
11. Micro USB port & MicroSD card slot
12. View area
13. Strap hook
14. Tripod connection
15. Battery compartments (left/right)

Charging the device

NOTE : The USB cable is to be used only for charging the device, not for data transmission.

1. Open the cover of the Micro USB port.

2. Connect the USB-A plug of the included USB cable with your cellphone power adapter.
   NOTE : Only use 5V/2A adapter. The charging time is approx. 3 hours (full charge).
   For first charge, it is recommended NOT to charge through Notebook/PC USB port, as the power current is not as strong as cellphone chargers.

3. Insert the Micro USB plug of the icluded USB cable into the Micro USB port of the device.

4. Put the Euro plug of the cellphone power adapter* into the wall socket.
   NOTE : Due to the nature of Li-Ion batteries, it is recommended to charge them at least once every three months, even if the device is not in use. This helps to activate the battery regularly and to extend the battery life.

Using the device at day

1. Press the Power button to turn on the device. Once the power is on, you will see an image in the view area.
2. Adjust the focus by turning the objective lens.
3. For daytime use, make sure the IR is off. If the image is in color, the IR is off.

Using the device at night

1. Press the Power button to turn on the device. Once the power is on, you will see an image in the view area.
2. For night use, turn on the IR by pressing the IR button. Increase the brightness by pressing the IR button, and decrease the brightness by pressing the IR button. You can choose from 7 levels of brightness (1 to 7).

Adjusting the screen brightness
Press the Power button briefly to adjust screen brightness in 8 levels. Once chosen, the number of screen brightness will disappear in 3 seconds.
Using digital zoom
Press the Zoom/Back button to zoom in at multiple levels. The maximum zoom is 3X. Once at 3X, keep pressing Zoom to go back to 1X.
Using the rangefinder
When looking at an object, press the RF button to measure the distance from your postion to the object. Press and hold the RF button to switch between yards (Yd) and meters (M).
Inserting a MicroSD card
To take photos and videos, you have to insert a suitable MicroSD card* first. Files taken will then be saved on the card.

1. Make sure that the device is turned off.
2. Insert the card and push the card into the card slot to lock it.
3. To remove the card, push it to release.
4. When the card is partially ejected, you can pull it out of the card slot.
   Note : When using a card with files saved, it is recommended to save the files on your computer first, and format the card before use.

If the “Memory Full” warning message appears on the LCD screen, the Micro SD card is full. Please transfer all the files to your computer and delete the files on the card. Then the card can be used again.

Taking pictures
Note: Insert a suitable MicroSD card* before you start.

1. Turn on the device.
2. Press MODE button to enter photo mode. Check the top left corner of the screen for the icon. If the icon is not visible, press the MODE button multiple times until the icon is visible.
3. Press the Camera/OK button to take photos.

Display:

Recording videos

Note : Insert a suitable MicroSD card* before you start.

1. When device is turned on, it will be in video mode automatically.
2. Check the top left corner of the screen for the icon. If the icon is not visible, press the MODE button multiple times until the icon is visible.
3. Press the Camera/OK button to record videos. Press the button again to stop recording.

Display:

Playback

1. Press the Mode button until either the icon or is visible in the top left corner of the screen.
2. The LCD screen will show the file saved last. If it was a photo, the photo will be shown on the screen, with icon in the top left corner. If it was a video, the icon will be visible in the top left corner.
3. Press the IR button to go to the next file or press the IR button to go to the previous file.
4. If it is a video, press Camera/OK button to play, delete current or delete all files or exit.

Displays

Menu settings

This is to set up parameters for the device if you wish to change default settings. Press M button multiple times until the menu shows up. Press IR button to go up the menu, or IR button to go down the menu. Press Camera/OK button to enter. Once the desired setting is selected, press Camera/OK to save it. When everything is set, press Mode button to exit back to the video mode.

Main menue

Auto Power off

Format SD Card

Lidar Stamp

Lidar Unit

Date YY/ MM/ DD

YY|  Press Camera/OK to enter YY set up and use IR   or IR   to select numbers. Once confirmed, press Camera/OK again.
---|---
MM| Press IR   to move to MM, press Camera/OK to enter MM set up, and use IR or IR   to select numbers. Once confirmed, press Camera/OK again.
DD| Press IR   to move to DD, press Camera/OK to enter DD set up, and use IR or IR   to select numbers. Once confirmed, press Camera/OK again.

Time hr/ min/ sec

hr|   Press Camera/OK to enter hr set up and use IR  or IR  to select numbers. Once confirmed, press Camera/OK again.
---|---
min| Press IR   to move to MM, press Camera/OK to enter min set up, and use
IR   or IR   to select numbers. Once confirmed, press Camera/OK again.
sec| Press IR   to move to DD, press Camera/OK to enter sec set up, and use
IR   or IR   to select numbers. Once confirmed, press Camera/OK again.

Date/ Time Tag

Replacing Batteries

NOTE : If the battery does not function anymore, new Li-Ion batteries will need to be installed.
Only use Li-Ion rechargeable batteries as specified in chapter „Specifications“.

1. Open the battery compartments with a screw driver. Keep the screw in a safe place so it does not get lost. Replace the old batteries with the new 18650 batteries. Screw the battery compartment back tightly.
2. For your safety, it is suggested to use only legitimate, branded batteries.

Specifications

General

day
Object lens Focus| Manually adjustable
Visual angle| 10.5° degrees
Range-Finding Distance| 200 meters (220 yards); with light-colored animal skin it can be 64 meters (70 yards)
Range-Finding Angle| Up to 80 degrees up and down
Luminance| 850 Infrared LED
External Memory| Compatible with MicroSD cards from 4 to 64 GB
Power Supply| Replaceable Li-Ion battery 18650 3200mAh X 2pcs (included)
Power Life| Up to 10 hours for day use, 5 hours for night use
Recharging| USB cable
Buttons| RF, Power, Zoom/Back, IR  or IR , Camera/OK, Mode
Unit Size|   19.67cm x 14cm x 7.5cm (approx.)
7.74” x 5.51” x 2.95” (approx.)
Net Weight| 635g
Colors| Black (rubber spray)

Li-Ion rechargeable batteries

Type: Li-Ion 18650 rechargeable battery
Power: 3.7V
Capacity: min. 3,000mAh recommended for better power life
NOTE : The battery must have a cap (i.e. cannot be flat top). It must be between 18mm and 19mm wide, and between 68mm and 69mm tall.

Troubleshooting

Device Power Off:

• As IR (Infrared) LED is power-consuming, when used under low power, the device may shut down to protect the circuit. In this case, you can charge via a cellphone charger or a power bank.
• Due to the nature of Lithium-Ion battery (aka Li-Ion battery), it is recommended that the device is being charged at least once every three months, even if it is not in use. This helps to activate the battery regularly and extend the battery life. If the battery does not function anymore, new Li-Ion batteries will need to be purchased. For instructions on purchasing new batteries, please see chapter “Replacing Batteries”.

Poor Image:

• If you wear glasses, please keep them on while using the device.
• For day use, please make sure the IR is off. For night use, make sure the IR is on.
• Adjust the focus by slowly turning the objective lens at the front of the device. Make sure it is focused.

Why is “No SD Card” message showing on the screen while the Micro SD card has been inserted?

• Please turn off the power, insert the card once more and check again.
• If the issue persists, please check the Micro SD card. In some cases, Micro SD cards may fail to be read due to compatibility issue. Try inserting another Micro SD card.

Cleaning and Maintenance

Before cleaning the device, disconnect it from the power supply (remove batteries)! Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid. Clean the eyepieces and/or lenses only with a soft, lint-free cloth, (e.g. microfibre cloth). To avoid scratching the lenses, use only gentle pressure with the cleaning cloth. Protect the device from dust and moisture. Store it in the supplied bag or transportation packaging. Remove the batteries from the unit if it is not used for a long period of time.

EC DECLARATION OF CONFORMITY
****Bresser GmbH has issued a „Declaration of Conformity“ in accordance with applicable guidelines and corresponding standards. The full text of the EU declaration of conformity is available at the following internet address:
www.bresser.de/download/9677494/CE/9677494_CE.pdf

UKCA DECLARATION OF CONFORMITY
** Bresser GmbH has issued a „Declaration of Conformity“ in accordance with applicable guidelines and corresponding standards.
The full text of the declaration of conformity is available at the following internet address: www.bresser.de/download/9677494/UKCA/9677494_UKCA.pdf
Bresser UK Ltd.**

• Suite 3G, Eden House, Enterprise Way, Edenbridge, Kent TN8 6HF, Great Britain

DISPOSAL

Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage!
As per Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.
In accordance with the regulations concerning batteries and rechargeable batteries, disposing of them in the normal household waste is explicitly forbidden. Please make sure to dispose of your used batteries as required by law — at a  local collection point or in the retail market. Disposal in domestic waste violates the Battery Directive.
Before disposing of removable batteries and rechargeable batteries, you must remove them from the electrical device and dispose of them separately at the designated collection points. To protect them against short-circuiting, tape the terminals of the Li-Ion batteries with non-conductive adhesive tape before disposal.

WARRANTY AND SERVICE

The period of warranty is 5 years, beginning on the day of purchase. Please keep the cash receipt as evidence of purchase. Devices which become defective during the warranty period can be returned to the dealer where the device was bought. The repaired device or a new one will then be returned to you. In the case of defects which occur after the end of the warranty period, the devices can also be returned. However, repairs which become necessary after the end of the warranty period will be subject to a service fee.

Service

Please contact the service centre first for any questions regarding the product or claims, preferably by e-mail.
E-Mail: service@bresseruk.com
Telephone*: +44 1342837098
BRESSER UK Ltd.
Suite 3G, Eden House
Enterprise Way
Edenbridge, Kent TN8 6HF
Great Britain
“Number charged at local rates in the UK (the amount you will be charged per phone call will depend an the tariff of your phone provider), calls from abroad will involve higher costs.

Bresser GmbH
Gutenbergstr. 2
46414 Rhede · Germany
www.bresser.de
@BresserEurope| Bresser UK Ltd.
Suite 3G, Eden House
Enterprise Way
Edenbridge, Kent TN8 6HF
Great Britain
---|---

Errors and technical changes reserved.
Manual_9677494_NV-Explorer-200RF_de-en_BRESSER_v042024a

References

• Bresser | Startseite | Expand Your Horizon mit BRESSER

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>