Extron DTP HDMI 4K 330 Digital Video Extender User Guide

Extron DTP HDMI 4K 330 Digital Video Extender

Specifications

• Extends HDCP-compliant HDMI signal up to 330 feet (100 m)
• Power: 12V 0.7A
• Audio input: unbalanced stereo via 3.5 mm mini stereo jack
• Connectivity: HDMI, RS-232, IR, DTP RJ-45

Installation

Step 1 – Mounting

Turn off or disconnect all equipment power sources and mount the Tx and Rx units as required.

Step 2 – Connections

1. HDMI Input connector (Tx): Connect an HDMI cable between this port and the HDMI output port of the digital video source.
2. Audio input (Tx): Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack for analog audio input.
3. RS-232 and IR connectors: Connect primary and secondary devices via RS-232 and IR captive screw connectors on both units.
4. DTP RJ-45 connectors: Connect transmitter DTP Out to receiver DTP In.
5. HDMI Output connector (Rx): Connect a display with an HDMI input for the display of the transmitted digital image.
6. Audio Output connector (Rx): Connect a balanced or unbalanced stereo or mono audio device to the receiver via the Audio captive screw connector.
7. Power connector: Connect an IEC power cord between the included 12 VDC power supply and a 100-240 VAC, 50-60 Hz source.

Frequently Asked Questions

Q: What is the maximum distance the Extron DTP HDMI 4K 330 can extend an HDMI signal?

A: The DTP HDMI 4K 330 can extend an HDCP-compliant HDMI signal up to 330 feet (100 m).

Q: How do I securely fasten the input and output connectors?

A: Refer to the LockItTM Lacing Brackets provided on the back of the user guide to securely fasten the input HDMI connector to the transmitter and the output HDMI connector to the receiver.

Q: What cables should be used for termination according to Extron’s recommendations?

A: Extron recommends terminating both cable ends per TIA/EIA T568B specifications at a minimum.

• IMPORTANT NOTE: Go to www.extron.com for the complete DTP HDMI 4K 330 user guide, and specifications before connecting the product to the power source.
• This guide provides quick start instructions for an experienced installer to set up and operate the Extron DTP HDMI 4K 330 digital video extender.
• The DTP HDMI 4K 330 transmitter and receiver pair can extend an HDCP-compliant HDMI signal up to 330 feet (100 m).

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the Tx and Rx units as required.

DTP HDMI 4K 330 Tx Rear Panel

DTP HDMI 4K 330 Rx Rear Panel

Step 2 — Connections

1. HDMI Input connector (Tx) — Connect an HDMI cable between this port and the HDMI output port of the digital video source.
   • NOTE: See the LockIt™ Lacing Brackets on the back of this guide to securely fasten the input HDMI connector to the transmitter.
2. Audio input (Tx) — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack for an analog audio input.
3. RS-232 and IR connectors — To pass serial or infrared data or control signals, such as serial control of a projector, connect the primary device to the transmitter and the secondary device to the receiver via the RS-232 and IR captive screw connectors on both units.
4. DTP RJ-45 connectors — Connect transmitter DTP Out to receiver DTP In.
   • Extron recommends that you terminate both cable ends under the following specifications, at a minimum:
   • TIA/EIA T 568 B
   • CAT 6A, shielded
   • 24 AWG, solid conductor
   • ATTENTION:
   • Do not connect these devices to a computer data or telecommunications network.
   • Ne connectez pas ces appareils à un réseau de télécommunications ou de données informatiques..
   • Signal LED — Lights when the unit is receiving a TMDS clock signal on the HDMI input (transmitter) or any valid signal on the DTP In connector (receiver).
   • Link LED — Lights when a valid link is established between the units on the DTP cable.
     **** Pin| TIA/EIA T568B

Wire color

---|---
1| White-orange
2| Orange
3| White-green
4| Blue
5| White-blue
6| Green
7| White-brown
8| Brown
5. HDMI Output connector (Rx) — Connect a display with an HDMI input for display of the transmitted direct digital image.

• NOTE: See the LockIt™ Lacing Brackets to securely fasten the output HDMI connector to the receiver

6. Audio Output connector (Rx) (see the drawing on) — Connect a balanced or unbalanced stereo or mono audio device to the receiver via the Audio captive screw connector. See the drawing below.
7. Power connector — Connect an IEC power cord between the included 12 VDC power supply and a 100-240 VAC, 50-60 Hz source.
   • Connect the power supply to either unit as shown at right. Use the included tie-wrap to strap the cord to the captive screw connector.

ATTENTION:

• Connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (-) contacts.
• Raccordez les manchons à la masse (GND). Ne PAS connecter les manchons aux contacts négatifs (–).
• NOTE: Only one power supply is required. A single power supply connected to either unit in the pair powers both units. A power supply is included with each transmitter.

Operation

After all devices are powered up, the system is fully operational. See the definitions of the power indications (shown at right), below:

1. Power LED (front panel)
   • Amber — The unit is receiving power, either locally or remotely (on the DTP cable).
   • Green — The unit is powered on and is receiving an active HDMI signal, either on the HDMI input if a transmitter, or transmitted on the DTP cable if a receiver.
2. Power LED (rear panel)
   • Amber — The unit is receiving power remotely (on the DTP cable).
   • Green — The unit is receiving power locally.

If any problems are encountered, verify that the cables are routed and connected properly. If your problems persist, call the Extron S3 Sales and Technical Support Hotline that is closest to you, at the number shown below.

LockIt™ Lacing Brackets

1. Use an included LockIt Lacing Bracket to securely fasten an HDMI cable to each device as follows.
2. Plug the HDMI cable into the panel connection (1).
3. Loosen the HDMI connection mounting screw from the panel enough to allow the LockIt lacing bracket to be placed over it (2). The screw does not have to be removed.
4. Place the LockIt lacing bracket on the screw and against the HDMI connector, then tighten the screw to secure the bracket (3).
   • ATTENTION: Do not overtighten the HDMI connector mounting screw. The shield it fastens to is very thin and can easily be stripped.
5. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing bracket as shown (4).
6. While holding the connector securely against the lacing bracket, use pliers or similar tools to tighten the tie wrap, then remove any excess length (5).

• For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide on the Extron website.
• © 2013 – 2024 Extron — All rights reserved. www.extron.com
• All trademarks mentioned are the property of their respective owners.
• Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

References

• Extron - The AV Technology Leader

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>