Simply Retrofits 120VAC Round Retrofit Downlight Instruction Manual
- June 14, 2024
- Simply Retrofits
Table of Contents
www.simplyretrofits.com
5″ &6″ ROUND RETROFIT DOWNLIGHT
4WAY CCT Adjustable
READ BEFORE INSTALLATION
SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble,
operate or install this product. This product must be installed in accordance
with any applicable installation code(s) by a qualified electrician or person
familiar with the construction and operation of the product and the hazards
involved.
WARNING
- RISK OF FIRE OR ELECTRIC SHOCK: The electrical rating of this product is 120VAC.
- RISK OF FIRE OR ELECTRIC SHOCK: Install his product only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings in this manual.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- RISK OF SHOCK — DISCONNECT POWER BEFORE INSTALLATION
- Do not make or alter any open holes in an enclosure of wiring or electrical components during installation.
- THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS.
- RISK OF FIRE OR ELECTRIC SHOCK: LED Recessed Downlight with Trim installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
CAUTION
To avoid possible electrical shock, be sure that the power is turned off at
the fuse box or circuit breaker before installing or servicing the product.
For your safety, read and understand the instructions completely before
beginning installation.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate
the receiving antenna. Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. Consult the dealer or an experienced
radio/TV technician for help. Any changes or modifications not expressly
approved by the manufacturer could void the user’s authority to operate the
equipment.
PACKAGE CONTENTS
Before beginning installation of this product, make sure all parts are present. Compare parts with package contents list and diagram. If any part is missing or damaged, do not attempt to assemble, install or operate this product.
| COMPONENTS INCLUDED
---|---
A| (1) MEDIUM BASE ADAPTER
B| (1) RECESSED DOWNLIGHT
C| (1) INSTRUCTION MANUAL
PRODUCT ELECTRICAL RATINGS
120 V/ 60 Hz, 120 mA, 11.1 W
SUITABLE FOR DAMP LOCATIONS
Suitable for Type IC Housings and Non-IC Housings.
Continuous dimming between 10% – 100% with most dimmers
LIGHTING DISTRIBUTION
HOW TO SELECT YOUR LIGHT COLOR OR NIGHTLIGHT
This product comes with a dual feature that allows you to select between downlight mode and nightlight mode.
- Downlight mode provides a selection of five color temperatures.
- Nightlight mode provides low light output at a soft color temperature.
NOTICE: The toggle switch is
located on the back of the fixture.
PICK YOUR FAVORITE LIGHT COLOR BEFORE INSTALLING
- You can lock in one color temperature.
- When the slide switch is set to 3K, the color temperature is set at 3000K.
- When the slide switch is set to 4K, the color temperature is set at 4000K.
- When the slide switch is set to 5K, the color temperature is set at 5000K.
HOW TO SWITCH TO NIGHTLIGHT MODE
- Toggle the wall switch to power on the light.
- Atinitial light up, the product is set to downlight mode.
- To transition to nightlight mode, toggle the wall switch off and back on within 2 seconds.
- To transition back to downlight mode, toggle the wall switch off and back on within 2 seconds
INLLATION INTO EXISTING RECESSED FIXTURE
NOTE: For use with 5 in. and 6 in. recessed housings (housing sold separately)
- Turn off the power at the switch and fuse box or circuit breaker.
- Remove the existing trim installed in the recessed housing (if necessary).
- If applicable, slide the lampholder bracket to its upward maximum position. If necessary, remove the lampholder mounting bracket by removing the wing nut and the lampholder from the bracket, then attach the provided label to the existing luminaire.
- Install the medium base adapter into the socket.
- Connect the two terminals together.
- Insert the torsion springs into the fixture housing brackets. When installing the product into a 5 in. recessed housing, the torsion spring must be moved. Unscrew the torsion spring from the 6 in. position and move to the 5 in. position. NOTE: Select preferred light color before installing.
- Gently push the product in until it is flush to the ceiling.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>