GOOVER B0CYBWG1S3 COB LED Strip Lights Kit User Guide
- June 1, 2024
- GOOVER
Table of Contents
USER GUIDE
(UL COB STRIP LIGHT KIT)
IMPORTANT SAFETY INFORMATION
WARNING: Do not stare directly at the LED chips. Eye damage may occur.
CAUTION:
- Do not power the LED strip while coiled on reel.
- Ensure correct polarity for 12-volt connections: (+) to (+), (-) to (-).
- Do not install low-voltage wiring next to AC power lines. Maintain a 90-degree angle if they cross.
- Secure cables and wires with insulated staples, plastic ties, or clips.
- Use only the provided DC 12V power supply. Avoid bending, crushing, or pulling the cable.Protect from sharp edges, oil, and heat.
- Securely fasten connectors before operating
Disposal: Electrical waste should not be disposed of with household waste.
Recycle responsibly at designated facilities.
WHAT YOU GET
| 16,4ft COB Strip Light | 1 |
|---|---|
| Controller | 1 |
| Wireless Remote | 1 |
| 48W Power Adapter | 1 |
| Double Head Connector | 1 |
| Wire Clips | 2 |
CONNECTION DIAGRAM
REMOTE FUNCTIONS
The included remote controller lets you easily adjust the brightness of
your lights to create the perfect ambiance. 
Connector: Optional Use for
Custom Bends
Match the “+ signs: Ensure the sign on the + sign LED strip aligns with the
“+ sign on the connector.
Gently press and secure: Carefully press the strip into the connector until
the prongs make a firm connection. Apply gentle pressure to ensure a good fit.
CONNECTOR INSTALLATION
-
OPTIONAL: If using connectors cut the strip light across indicated lines.
IMPORTANT:
If using the connector, match wire colors and polarity markings on the strip to those on the connector. Ensure that the “+” and “-” signs align correctly.
Gently press and secure: Carefully press the strip
into the connector until the prongs make a firm connection. Apply gentle
pressure to ensure a good fit. -
Clean surface where you intend toinstall the GOOVER LED Strips.
-
Remove the backing from the light strip to reveal adhesive tape.
-
Press down and run the stripin a straight line onto the surface.
-
Use mounting clips if needed to make power source wire and strips stable.
-
Use connector included if needed to extend LED strips around corner.
-
Power on to ensure your new led strip lights up and functions properly.
TROUBLESHOOTING
Lights not turning on?
- Double-check the connection between the strip and the power source.
- Remember: GOOVER LED strips require a 12V DC power source.
- Ifusing a controller, ensure its switched on.
Lights not lighting up?
- Verify the power source’s voltage. It must be 12V DC for proper function.
- Anything below the required voltage (12V DC) may resultin lights not lighting up.
Adhesive tape not sticking?
- Thoroughly clean the mounting surface with rubbing alcohol or a similar cleaner.
- Mounting tape may not adhere effectively to certain surfaces like wood, stone, or rough materials.
- Try these alternatives: GOOVER Foam Tape, Mounting Clips, or An adhesive suited to the material in question.
WARNING!
DO NOT CONNECT DIRECTLY TO HIGH VOLTAGE POWER! Read all warnings and
installation instructions thoroughly.
HANDLE LED STRIP LIGHT WITH CARE!
DO NOT BEND LED STRIP LIGHT TO A ‘DIAMETER LESS THAN 1.5 INCHES.| DO NOT
FOLD,CREASE OR TW IST LED STRIP LIGHT
DO NOT BEND LED STRIP LIGHT ‘ON A HORIZONTAL PLANE| DO NOT PUT EXCESSIVE
PRESSURE ‘ON SURFACE OF STRIP LIGHT (BLASS /ACRYLIC PANES, ETC.)
DO NOT COVER STRIP LIGHT WITHANY MATERIALS.| O NOT POWER STRIP LIGHT WHILE ATTAGHED TO SPOOL OR TIGHTLY COILED.
Three-year warranty
Have any questions or concerns?
Please contact us!
service@gooverlight.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>