LABCONCO 44003 Series Steam Scrubber Glassware Washer User Manual

LABCONCO 44003 Series Steam Scrubber Glassware Washer

Specifications

• Models: 44003 Series, 44004 Series, 44203 Series, 44204 Series, 45780 Series, 45781 Series
• Warranty: Repair or replacement of parts and labor for normal and proper use with compatible chemicals
• Exclusions: Broken glassware, filters, gaskets, light bulbs, finishes, lubrication, improper installation, unauthorized repair, incompatible chemicals

Product Usage Instructions

Chapter 1: Introduction

Safety Symbols: Familiarize yourself with safety symbols for proper usage.

Chapter 2: Prerequisites

• Hot Water Requirements
• Purified Water Requirements
• Electrical Requirements
• Drain Requirements
• Space Requirements
• Safety Precautions: Follow safety precautions for safe
  operation.

Chapter 3: Getting Started

• Unpacking Your Glassware Washer
• Washer Components
• Washer Installation Steps:
  • Installing Leveling Feet
  • Leveling the Washer
  • Centering the Washer Door
  • Securing the Washer to the Countertop
  • Connecting Water Services: Hot water supply, purified water supply, drain hose
  • Connecting Power Supply
  • Controller Set Up
  • Testing Your Washer
  • Running Diagnostics

Chapter 4: Using Your Washer

• Arranging the Washer Racks: SteamScrubber Racks, FlaskScrubber Spindle Rack
• Loading Glassware into the FlaskScrubber
• The Detergent Dispenser
• Filling the Neutralizing Acid Dispenser

FAQs

• Q: What should I do if my shipment was damaged in transit?
  • A: File a claim directly with the freight carrier within fifteen (15) days of delivery. Unauthorized returns will not be accepted.
• Q: How can I contact Labconco Corporation for assistance?
  • A: Contact Labconco’s Customer Service Department or Product Service Department at 1-800-821-5525 or 1-816-333-8811 between 7:30 a.m. and 5:30 p.m., Central Standard Time.
• Q: What is excluded from the warranty coverage?
  • A: Broken glassware, maintenance items like filters, gaskets, light bulbs, finishes, lubrication, improper installation, unauthorized repair, and use with incompatible chemicals are not\ covered under warranty.

SteamScrubber & FlaskScrubber Glassware Washers
Models
44003 Series 44004 Series 44203 Series 44204 Series 45780 Series 45781 Series

Copyright © 2019 Labconco Corporation. The information contained in this manual and the accompanying products are copyrighted and all rights reserved by Labconco Corporation. Labconco Corporation reserves the right to make periodic design changes without obligation to notify any person or entity of such change.
Warranty
Labconco Corporation provides a warranty to the original buyer for the repair or replacement of parts and reasonable labor as a result of normal and proper use of the equipment with compatible chemicals. Broken glassware and maintenance items, such as filters, gaskets, light bulbs, finishes and lubrication are not warranted. Excluded from warranty are products with improper installation, erratic electrical or utility supply, unauthorized repair and products used with incompatible chemicals.
SteamScrubber® & FlaskScrubber® Glassware Washers carry a two-year warranty from date of installation or three years from date of shipment from Labconco, whichever is sooner. Warranty is non-transferable and only applies to the owner (organization) of record.
Buyer is exclusively responsible for the set-up, installation, verification, decontamination or calibration of equipment. This limited warranty covers parts and labor, but not transportation and insurance charges. If the failure is determined to be covered under this warranty, the dealer or Labconco Corporation will authorize repair or replacement of all defective parts to restore the unit to operation. Repairs may be completed by 3rd party service agents approved by Labconco Corporation. Labconco Corporation reserves the rights to limit this warranty based on a service agent’s travel, working hours, the site’s entry restrictions and unobstructed access to serviceable components of the product.
Under no circumstances shall Labconco Corporation be liable for indirect, consequential, or special damages of any kind. This warranty is exclusive and in lieu of all other warranties whether oral, or implied.
Returned or Damaged Goods
Do not return goods without the prior authorization from Labconco. Unauthorized returns will not be accepted. If your shipment was damaged in transit, you must file a claim directly with the freight carrier. Labconco Corporation and its dealers are not responsible for shipping damages. The United States Interstate Commerce Commission rules require that claims be filed with the delivery carrier within fifteen (15) days of delivery.
Limitation of Liability
The disposal and/or emission of substances used in connection with this equipment may be governed by various federal, state, or local regulations. All users of this equipment are required to become familiar with any regulations that apply in the user’s area concerning the dumping of waste materials in or upon water, land, or air and to comply with such regulations. Labconco Corporation is held harmless with respect to user’s compliance with such regulations.
Contacting Labconco Corporation
If you have questions that are not addressed in this manual, or if you need technical assistance, contact Labconco’s Customer Service Department or Labconco’s Product Service Department at 1-800-821-5525 or 1-816-333-8811, between the hours of 7:30 a.m. and 5:30 p.m., Central Standard Time.
Part #4591100, Rev. P ECO L668

CHAPTER 1

INTRODUCTION

Congratulations on your purchase of a Labconco Glassware Washer. Labconco manufactures two types of Glassware Washers, the SteamScrubber® and the FlaskScrubber®. Each of these washers is available in an Undercounter, an Undercounter 33 or a Freestanding model. An optional kit is available to convert Freestanding models to Mobile models. Each washer model is available in 115V or 230V, and with or without a window in the door.
Your Labconco Glassware Washer is designed and manufactured to thoroughly clean your laboratory glassware and accessories and complies with NSF/ANSI 3 standards for sanitization. You can select pre-programmed wash cycles or program customized wash cycles to meet your requirements.
The Glassware Washer graphic display provides operational information. Models with a window and light in the door allow you to visually monitor the operation of your washer. Wash cycles may be programmed to provide steam and the use of purified water in the rinse cycles, allowing you to choose the best conditions for cleaning your glassware.
Safety Symbols
Your Glassware Washer was designed with safety in mind, however conditions may exist that could be hazardous.

Throughout this manual potentially hazardous conditions are identified using the following words and symbols.

Product Service 1-800-522-7658

1

Chapter 1: Introduction
It is important that you understand the warnings listed throughout this manual before you operate the Glassware Washer.

2

Product Service 1-800-522-7658

CHAPTER 2

PREREQUISITES

Before you install the Glassware Washer, prepare your site for installation. Carefully examine the location where you intend to install the Glassware Washer. You must be certain that the area is level and of solid construction. In addition, a hot water source, a drain, a purified water source (if applicable), and an electrical source must be located near the installation site. A cold water source is required when the optional Cool Drain Water Kit is installed.
Refer to Appendix C: Glassware Washer Specifications for complete Glassware Washer electrical and environmental conditions, specifications and requirements.
Hot Water Requirements
An existing hot water supply may be used as the hot water source for your Glassware Washer. Labconco recommends the inlet water temperature to be greater than 120°F (49°C) to fully activate powdered detergents and raise the glassware temperature to achieve fast and complete drying. Hotter water will produce better washing results.
Water pressure must be between 20-120 psi (138-827 kPa) at the washer and provide a minimum of 1.25 gallons (4.7 liters) per minute flow rate.
A shut-off valve should be installed in the water supply line plumbed to the washer. The hot water inlet valve on the Glassware Washer is equipped with a female 3/8 NPT fitting. A compression fitting is provided that connects to .375″ (9.53mm) OD copper tubing.
Purified Water Requirements
To use purified water for the rinse cycles, a purified water supply is required. The washer can be connected to an in-house, pressurized, purified water tap; a water purification system; or a non-pressurized purified water container.

Product Service 1-800-522-7658

3

Chapter 2: Prerequisites
The purified water system must be provided with supply piping of sufficient size to permit at least 0.9 gallons (3.4 liters) per minute of flow. Tubing with an internal diameter of at least .375″ (9.53 mm) is recommended. The purified water inlet valve on the washer is equipped with a plastic hose barb connection to accommodate .375″ (9.53 mm) ID flexible plastic or rubber hose. Use a spring or band hose clamp to secure the hose to the hose barb connection. The hose barb connection may be removed from the valve to expose a male 3/4″ – 11-1/2 NH hose coupling. Rigid plastic, tin-lined, or stainless steel tubing and fitting can be connected to the washer fitting.
An optional connection kit (Labconco P/N 4592200) is available for connecting .375″ (9.53mm) OD plastic tubing to the purified water inlet valve. The purified water system connections must be airtight to prevent the washer pump from pulling air instead of water.
If the purified water is stored in a carboy, at least 3.4 gallons (13 liters) must be available for each rinse. If all the purified water is not available at the start of a wash cycle, but instead is produced concurrently with the wash cycle, the production rate must permit at least 0.9 gallon (3.4 liters) per minute to be delivered to the washer.
Electrical Requirements
Undercounter and Freestanding models, are hard-wired directly into a junction box using conduit. A 20 Amp circuit breaker or fuse is required for models rated at 115V (60 Hz) or 230V (50/60 Hz).
High voltage models are designed to operate at 230 VAC, single phase. It will operate safely at nominal 208 VAC, however the heater output will be reduced proportionally. As the operating voltage drops below 230V a boost transformer can be used if higher voltage is preferred.
If your Glassware Washer is converted to a Mobile model, a dedicated electrical outlet is required. A 20 Amp circuit breaker or fuse is required for models rated at 115V (60 Hz) or 230V (50/60 Hz). 115V models are equipped with a 20 Amp NEMA 5-20P plug. 230V models are equipped with a 15 Amp NEMA 6-15P plug. It may be necessary to remove the plug and install a different plug to match the available receptacle.

4

Product Service 1-800-522-7658

Chapter 2: Prerequisites
Drain Requirements
The drain hose, .57″ (1.45 cm) ID is installed during manufacture. The hose provides a flexible coupling to the building drain piping and can be secured with a spring or band hose clamp. (A band hose clamp is provided with the washer.)
Tubing or pipe, 5/8″ (1.6 cm) ID or larger, should be provided for the building drain. The use of an air gap is strongly recommended to prevent siphoning of wastewater into the washer.
Do not reduce the size of the drain plumbing.
Glassware Washers that have been converted to Mobile models drain into a sink through a hose assembly that attaches to the faucet.
Space Requirements
If your Glassware Washer is an Undercounter model, you must ensure the undercounter opening is the proper size to accommodate the washer. The dimensions for the Undercounter washer are shown in Appendix B.
Safety Precautions
When lifting this product, use at least two (2) persons and always use safe lifting practices.
Do NOT use a detachable power cord that is not adequately rated for this product.
Always disconnect power before beginning service operations.
Do not damage internal wiring or other components while service panels are removed. If internal wiring or components are damaged, do not restore power, contact Labconco’s Product Service Department immediately.
Wear all required Personnel Protective Equipment (PPE) during service operations. At a minimum, this includes: eye protection, breathing protection, skin protection. Do not wear loose fitting clothes that can catch on internal surfaces.
After service, verify safe state of use before using the product. Contact Labconco’s Product Service Department for questions on determining safe state of this product.
Verify protective earth ground continuity before using equipment.
No special ventilation requirements.

Product Service 1-800-522-7658

5

Chapter 2: Prerequisites
No hazards exist for: explosion, implosion, or release of toxic or flammable gases arising from the materials being heated.
No Heat Transfer Media is required for the normal operation of this equipment.
Cleaning solutions that do not contain chlorine-based disinfectants (such as Bleach or hypochlorites) may be safely used on this equipment. If there is any doubt about the compatibility of decontamination or cleaning agents, contact Labconco’s Product Service Department.
To verify door safety interlock is functioning properly, close the washer door, secure the door latch, and start a program. Once program has begun, open the door by unlatching the door latch. All functionality must stop, and power is removed from the display screen (it goes black). If this result is not achieved, do not use the product and contact Labconco’s Product Service Department immediately.

6

Product Service 1-800-522-7658

CHAPTER 3

GETTING STARTED

Now that the site for your Glassware Washer is properly prepared, you are ready to unpack, inspect, install, and test your washer.

You may need common plumbing and electrical installation tools in addition to a 9/16″ wrench, a flat-blade screwdriver, a Phillips screwdriver, and a carpenter level to complete the instructions in this chapter.

The Glassware Washer weighs over 150 lbs. (68 Kg). The

!

carton allows for lifting with a mechanical lift truck or hand

truck. If you must lift the washer manually, use at least two (2)

persons and follow safe lifting guidelines.

Product Service 1-800-522-7658

7

Chapter 3: Getting Started

Unpacking Your Glassware Washer
Carefully unpack your Glassware Washer and inspect it for damage that may have occurred in transit. If your Glassware Washer is damaged, notify the delivery carrier immediately and retain the entire shipment intact for inspection by the carrier.
The United States Interstate Commerce Commission rules require that claims be filed with the delivery carrier within fifteen (15) days of delivery.
Do not discard the carton or packing material for your Glassware Washer until you have checked all of the components and installed and tested the Glassware Washer.
NOTE: Do not return goods without the prior authorization of Labconco. Unauthorized returns will not be accepted. If your Glassware Washer was damaged in transit, you must file a claim directly with the freight carrier. Labconco Corporation and its dealers are not responsible for shipping damage.

Do not remove the washer from its shipping skid until it is ready to be placed into its final location. Move the washer by placing a flat, low dolly under the shipping skid.

Washer Components
Locate the model of washer you received in the following group of tables. Verify that the components listed are present and undamaged.

Catalog # Washer Description

4400320

SteamScrubber Undercounter ­ 115 V with upper & lower racks

4400321

SteamScrubber Undercounter ­ 230 V with upper & lower racks

4400330

SteamScrubber Undercounter ­ 115 V with window, upper & lower racks

4400331

SteamScrubber Undercounter ­ 230 V with window, upper & lower racks

4578020

SteamScrubber 33 Undercounter ­ 115 V with upper & lower racks

4578021

SteamScrubber 33 Undercounter ­ 230 V with upper & lower racks

4578030

SteamScrubber 33 Undercounter ­ 115 V with window, upper & lower racks

4578031

SteamScrubber 33 Undercounter ­ 230 V with window, upper & lower racks

Plus the Following Loose Parts:

Part #

Component Description

1879801

Leveling Feet (4)

4591100

User Manual

4462900

Screws (2)

1488800

Clamp (1)

4522500

LabSolutions Powder Detergent with MSDS ­ 6 ounces (175 grams)

1410700

Water Connector

1448700

Coupling & Sleeve (1)

SteamScrubber Undercounter Models

Catalog #
4400420 4400421 4400430 4400431

Washer Description
SteamScrubber Freestanding ­ 115 V with upper & lower racks SteamScrubber Freestanding ­ 230 V with upper & lower racks SteamScrubber Freestanding ­ 115 V with window, upper & lower racks SteamScrubber Freestanding ­ 230 V with window, upper & lower racks

SteamScrubber Freestanding Models

8

Product Service 1-800-522-7658

Chapter 3: Getting Started

Plus the Following Loose Parts:

Part #

Component Description

1879801

Leveling Feet (4)

4591100

User Manual

4468000

Hole Plug (2)

1488800

Clamp (1)

4522500

LabSolutions Powder Detergent with MSDS ­ 6 ounces (175 grams)

1410700

Water Connector (1)

1448700

Coupling & Sleeve (1)

Catalog # Washer Description

4420320

FlaskScrubber Undercounter ­ 115 V with lower spindle rack

4420321

FlaskScrubber Undercounter ­ 230 V with lower spindle rack

4420330

FlaskScrubber Undercounter ­ 115 V with window with lower spindle rack

4420331

FlaskScrubber Undercounter ­ 230 V with window with lower spindle rack

4578120

FlaskScrubber 33 Undercounter ­ 115 V with lower spindle rack

4578121

FlaskScrubber 33 Undercounter ­ 230 V with lower spindle rack

4578130

FlaskScrubber 33 Undercounter ­ 115 V with window & lower spindle rack

4578131

FlaskScrubber 33 Undercounter ­ 230 V with window & lower spindle rack

Plus the Following Loose Parts:

Part #

Component Description

4584600

Lower Spindle Rack with 36 spindles

1879801

Leveling Feet (4)

4591100

User Manual

4462900

Screws (2)

1488800

Clamp (1)

4522500

LabSolutions Powder Detergent with MSDS ­ 6 ounces (175 grams)

1410700

Water Connector (1)

1448700

Coupling & Sleeve (1)

4525200

Spindle ­ Small (10)

4414703

Clip ­ Spindle (10)

4425101

Plug ­ Spindle (36)

Catalog # Washer Description

4420420

FlaskScrubber Freestanding ­ 115 V with lower spindle rack

4420421

FlaskScrubber Freestanding ­ 230 V with lower spindle rack

4420430

FlaskScrubber Freestanding ­ 115 V with window with lower spindle rack

4420431

FlaskScrubber Freestanding ­ 230 V with window with lower spindle rack

Plus the Following Loose Parts:

Part #

Component Description

4584600

Lower Spindle Rack with 36 spindles

1879801

Leveling Feet (4)

4591100

User Manual

4468000

Hole Plug (2)

1488800

Clamp (1)

4522500

LabSolutions Powder Detergent with MSDS ­ 6 ounces (175 grams)

1410700

Water Connector (1)

1448700

Coupling & Sleeve (1)

4525200

Spindle ­ Small (10)

4414703

Clip ­ Spindle (10)

4425101

Plug ­ Spindle (36)

FlaskScrubber Undercounter Models
FlaskScrubber Freestanding Models

Product Service 1-800-522-7658

9

Chapter 3: Getting Started
If you did not receive one or more of the components listed for your washer, or if any of the components are damaged, contact Labconco Corporation immediately for further instructions.
Removing the Shipping Skid
After you verify the washer components, move your washer to the location where you want to install it. Then, follow the steps listed below to remove the shipping skid from your washer.
To remove the shipping skid:
1. Remove accessories and loose items from inside the washer. Cut tie wraps and remove racks.
2. Gently place the washer on its back, positioning the washer on the shipping carton or other cushioning material.
3. Remove the four screws fastening the skid to the washer. 4. Retain the shipping skid until you test the various features of the washer.
Washer Installation
After you remove the skid from your washer, you must install leveling feet on the bottom of the washer. If you have an Undercounter or Freestanding model, then you must level the washer and center the washer door. If you have an Undercounter model, you must also secure the washer to the underside of the countertop or worksurface.
Installing the Leveling Feet
1. Locate the holes on the bottom of the washer where the four skid-fastening screws were previously attached.
2. Thread the four leveling feet into the holes. 3. Carefully move the washer into an upright position. Be careful to distribute
the weight evenly on the leveling feet when setting the washer upright. 4. Reinstall racks.

10

Product Service 1-800-522-7658

Chapter 3: Getting Started
Leveling the Washer
If you have a Freestanding model of the SteamScrubber or FlaskScrubber Glassware Washer, after you have installed the leveling feet, level the washer by adjusting the leveling feet. 1. Position the washer in its final installed location. 2. Place a carpenter level on the washer in the positions shown.
3. Turn the four leveling feet, as needed, to level the washer.

Product Service 1-800-522-7658

11

Chapter 3: Getting Started If you have an Undercounter model, level it side- to-side by placing a short level on the inside top edge of the door. See the figure below for the placement of the level on the washer. Check the level front to back by placing a level on the rail that the lower rack slides on.
Centering the Washer Door
When the washer is level, check the operation of the washer door for alignment with the washer tank. If the door is not centered in the opening, you must center the door by adjusting the corresponding leveling foot. (For example, if the door hits the right side of the tank, raise the right front corner of the washer. If the door hits the left side of the tank, raise the left front corner of the washer.)
Securing the Washer to the Countertop
If you have an Undercounter Glassware Washer, two screws have been provided to attach the front of the washer to the underside of the countertop or work surface. After the washer is leveled in its final position and the washer door is properly centered, install the two screws as shown in the figure below to stabilize the unit and prevent it from moving.

Connecting the Water Services

12

Product Service 1-800-522-7658

Chapter 3: Getting Started
A hot water supply must be attached to your Glassware Washer. In addition, a purified water source must be connected to your washer if pure water rinses will be required.
Connecting the Hot Water Supply
To prevent valve clogging, thoroughly flush the hot water lines for your hot water supply source prior to connecting the washer to the water lines. The water supply valve to which the hot water supply is connected is located on the back of the washer base. The back panel of FreeStanding models must be removed to access the valve.
You must provide the plumbing fittings and components needed to connect the hot water supply source. The washer hot water supply valve is equipped with a compression fitting for a .375″ (9.53 mm) OD tube.
To connect the hot water supply:
1. Be certain the hot water supply piping has been thoroughly flushed prior to connecting it to the washer. Debris in the piping can clog the washer valve.
2. Make the necessary plumbing connections to properly connect the hot water supply to the washer.
3. It may be necessary to place a loop in the supply tube to allow the washer to be slid in or out of its operating position. Be careful not to kink the water supply tube when the washer is placed into its final location. If kinking occurs, it may be necessary to replace the straight fitting on the valve with an elbow.

Washer Back View

Product Service 1-800-522-7658

13

Chapter 3: Getting Started
Connecting the Purified Water Supply
To prevent valve and pump clogging, flush all of the water lines for your purified water supply source prior to connecting the washer to the water lines. The valve to which the purified water supply must be connected is located on the back of the washer base. The back panel of Freestanding models must be removed to access the valve. Refer to the previous figure.
The purified water inlet valve is equipped with a plastic hose barb connection to accommodate .375″ (9.53 mm) ID flexible plastic or rubber hose. The hose connection may be removed from the valve to expose a male 3/4″ ­ 11-1/2 NH hose coupling. Rigid plastic, tin-lined, or stainless steel tubing and fittings may be connected to the washer fitting.
At least 0.9 gallon (3.4 liters) per minute of purified water flow is required. At least 3.4 gallons (12.9 liters) of purified water must be available for each pure rinse. A .375″ (9.5 mm) ID pipe is the minimum recommended.
If you do not use purified water during the rinse cycles, you may disable the purified water pump. Refer to Controller Set-Up in this section.
If the washer has been converted to a Mobile model and is moved to various locations, and if purified water is used, provisions must be made to use a flexible hose from a source of house-purified water. If a carboy is used, place the carboy on a carboy cart and move it with the washer. Be careful not to let the hose kink or become damaged.
To connect the purified water supply:
1. Make certain the purified water supply piping has been thoroughly flushed prior to connecting it to the washer.
2. Make the necessary plumbing connections to properly connect the purified water supply to the washer.
NOTE: If the purified water source is a carboy, complete steps 3 and 4.
3. Connect the purified water source through either the top or the bottom of the carboy, as illustrated in the following figures. If the purified water supply feeds directly from the carboy top, make certain the hose is submerged under the water line. Attach a weight to the end of the tubing to keep it from floating on top of the water and possibly allowing air into the system.
4. Make certain the top of the carboy is vented to permit proper flow from the carboy to the washer. Make certain that all of the connections on the purified water system are air tight. The pump must not pull air instead of water. Make certain the supply hose is not crimped.

14

Product Service 1-800-522-7658

Chapter 3: Getting Started

Example of a Bottom Feed Connection

Example of a Top Feed Connection

Product Service 1-800-522-7658

15

Chapter 3: Getting Started
Connecting the Drain Hose
Before continuing with this section, be certain that your drain meets the requirements detailed in Drain Requirements in Chapter 2: Prerequisites.
Be certain you conform to all local plumbing codes when you route and connect the drain.
The drain hose is installed at the factory. The hose provides a flexible coupling to the drain piping and can be secured with a spring or band hose clamp. (A band hose clamp is provided with your washer.)
Tubing or pipe 5/8″ (1.6 cm) ID or larger should be used for the drain.
Do not route the drain to an elevation more than 36″ (91 cm) above the pump discharge. Do not reduce the size of the drain plumbing.
Do not remove the hose from the clamp on the rear of the glassware washer.
The use of an air gap is strongly recommended for all installations to prevent the siphoning of wastewater into the washer.
The drain piping can be routed to either a sink or a floor drain. If you route the drain piping to a sink drain without using an air gap, the highest point of the drain pipe must be above the highest water level in the sink, as shown below.
If an air gap is not used, the drain line
must be elevated above the water level of the sink.

16

Product Service 1-800-522-7658

Chapter 3: Getting Started If you route the drain piping to a sink drain and use an air gap, refer to the figure below for the placement of the air gap.
Air gap
Drain line
If you route the drain piping to a floor drain, refer to the figure below for placement of the drain tubing and trap.

Drain trap

Product Service 1-800-522-7658

17

Chapter 3: Getting Started
Connecting the Power Supply
Before continuing with this section, be certain your power supply meets the requirements specified on the washer data plate and in Electrical Requirements in Chapter 2: Prerequisites. Undercounter and Freestanding Washers should be hard-wired directly into a junction box. Refer to the figure below and follow the steps below to connect your washer to the appropriate power source.
Be certain that you check and conform to all local electrical codes. Do not disturb any internal wiring in the washer.
If you are connecting to certain legs of a 3-phase power system to obtain singlephase power, be sure to consult a professional to insure codes/standards are followed. These professionals can determine the appropriate connections for either a Wye or Delta connected power source.
The supply circuit must consist of number 12 AWG 3-wire cable or heavier. Washers must be connected to a dedicated service with a 20 amp circuit breaker or fuse. Wire must comply with all local electrical codes. Type THW or THWN wire may be used if it complies.
To connect the electrical supply:
1. Remove 2 screws on each side of the middle panel.

2. Pull the middle panel forward and remove it. 3. Remove the lower panel on the washer front by removing the two screws
located at the bottom of the panel.

18

Product Service 1-800-522-7658

Chapter 3: Getting Started
4. Remove the cover over the electrical junction box by removing the two screws.
ELECTRICAL JUNCTION BOX

COVER
TOE KICK MOVEABLE LOWER DOOR PANEL

ROUTE POWER CORD THROUGH HOLE IN BACK CORNER
ROUTE POWER CORD THROUGH HOLE USE STRAIN RELIEF AS REQUIRED
CONNECT POWER CORD PER WIRING DIAGRAM

5. Make sure electrical power is turned off before making any connections. 6. On 115V models, connect the customer-supplied power wires to the black and
white wires, using wire connectors. On 230V models, attach customersupplied power wires to the brown and blue wires, using wire connectors. Customer- supplied wires must be clamped to the hole where they pass through the rear of the junction box, if prescribed by local codes. If it is necessary to use a bushing with an integral clamp at the inlet to the junction box, remove the plastic bushing supplied with the washer before installing the new customer supplied bushing. 7. Connect the customer-supplied ground wire to the green screw. 8. Replace the cover on the electrical junction box. 9. Replace the lower panel and door panel assembly on the washer.
Controller Set-Up
The washer control system has been set at the factory to agree with the configuration of the washer as it was shipped. The control may be customized or modified if certain optional accessories are added.

Product Service 1-800-522-7658

19

Chapter 3: Getting Started

To set up the washer control:

1. Locate the control panel on the front of the washer. 2. Press and hold the button and close the handle of the washer by sliding the door
latch knob to the right. Hold for 5 seconds.
3. The display will show the SET UP screen.
4. The > on the left side will highlight VOLTAGE. 5. Press the or buttons to select the correct operating voltage of the washer.
CAUTION: The voltage selected (115V or 230V) does not change the acceptable
AC mains voltage that can be connected to the washer. It only selects the
programs that are suitable for the identified voltage. 6. Press the button and TEMP UNITS will highlight. 7. Press or buttons to select either °F or °C which will be used on the display to
set and monitor temperature. 8. Press the button and DI PUMP ENABLE will highlight. 9. Press or buttons to YES or NO. This allows the pure water valve and pump
to be disabled if pure water will not be used for rinse cycles and prevents
inadvertently programming a cycle to have pure rinses. 10. Press the button and LIGHT will be highlighted on the display. 11. Press or to cause the light inside the tank on window models to be turned on
or off while the door is latched. 12. Press the button and LIQ DETERGENT OPT will be highlighted on the display. 13. Press or to activate the control for the liquid detergent dispense option if this
accessory has been installed. 14. Press the button and FACTORY RESET will be highlighted on the display. 15. Press the or to select YES to erase all program set points entered by the user
and to restore all set points that were active when the washer was shipped.
16. Press RUN to save all settings.

Testing Your Washer
Now that you have made the required water and electrical connections to your washer, a series of diagnostic steps are provided in this section to test the operation of the washer.

Before turning on the washer, make certain the water is turned on and no packing material remains inside the washer.

20

Product Service 1-800-522-7658

Chapter 3: Getting Started If the washer is interrupted in the middle of the diagnostic steps, wait 4 to 5 seconds before opening the washer door to prevent hot water from splashing out. The hot water and steam from the washer may cause scalding.
Running the Diagnostics
To ensure your washer is operating properly, perform the diagnostics procedure detailed below, which will take approximately 10 minutes to complete. Refer to the figure below to familiarize yourself with the control panel before you begin the procedure.

To run the diagnostics test:

1. Press the button on the control panel and close the door and slide the door latch to the right. Hold for 5 seconds.
2. The display will show the Diagnostics screen and the indicator on the left side
will point to TAP WATER VALVE. 3. Press either the or button to turn the tap water valve ON. Tap water
should enter the washer. Allow water to enter for approximately 1 minute. Press either the or button to turn the water off. 4. Press the button and the arrow on the display will point to PURE WATER. 5. Press either the or button turn the pure water pump ON and open the pure water valve. Allow pure water to enter the washer. After about 3
minutes the fill switch should cause the water flow to turn off. 6. Press the button and the arrow on the display will point to WASH PUMP. 7. Press the or button and the wash pump should energize.

Product Service 1-800-522-7658

21

Chapter 3: Getting Started
8. Press the button and the arrow on the display will point to DETERGENT CUP.
9. Press either the or button to energize the detergent cup. Within about 1 minute the detergent cup door should be heard to open.
10. Press the button and the arrow on the display will point to HEATER. 11. Press either the or button and the heater will be energized. 12. Press the button and the arrow on the display will point to DRAIN / COOL. 13. Press either the or button and the drain will be energized. Allow all
water to be drained from the washer. The sound of the pump will change
when all water is drained. This will take about 1-1/2 to 2 minutes. If the Cool
Water Drain Kit accessory has been installed, cool water will mix with hot
water draining from the washer. 14. Press the button and the arrow on the display will point to DRY BLOWER. 15. Press either the or button and the dry cycle blower will be energized. 16. The arrow in the lower right side of the display indicates that more
selections may be made. Press the button to select the next function to test. The arrow on the display will point to LIQ DETERG PUMP. 17. Press the or button and if the liquid detergent accessory has been installed and if it was activated in the Set Up procedure, the detergent pump
will operate. 18. Press the button and the arrow on the display will point to LIGHT. 19. Press either the or button and if the washer is equipped with a window
in the door, the light inside the washer will illuminate. 20. Press the button and the arrow on the display will point to COOL FAN. 21. Press either the or button and the small fan inside the kick panel will
operate.
22. This completes the check of most of the washer functions. Unlatch the door
to exit from the Diagnostics mode.
23. To verify the proper operation of the overfill switch, repeat steps 1 & 2 above. Press either or button and allow tap water to enter the tank until the water flow turns off.
24. Press and hold the RUN button. Water will enter the washer and should turn
off before it overflows. 25. Press the arrow until DRAIN/COOL is highlighted. 26. Press or button to drain water from the washer. 27. Unlatch the door to exit from the Diagnostics mode.

22

Product Service 1-800-522-7658

CHAPTER 4

USING YOUR WASHER

After your washer has passed the basic diagnostics test detailed in Chapter 3: Getting Started, you are ready to begin using your washer.
Arranging the Washer Racks
The FlaskScrubber and SteamScrubber are equipped with different rack configurations to accommodate the various types of laboratory glassware. In addition to the standard configuration of the Glassware Washers, many optional racks and inserts are available to customize your washer to best suit your needs. For a complete list of available rack accessories, refer to Appendix A: Glassware Washer Accessories.
If you purchased a SteamScrubber, proceed to the following section, The SteamScrubber Racks. If you purchased a FlaskScrubber, proceed to the section, The FlaskScrubber Racks, later in this chapter. A FlaskScrubber can be converted to a SteamScrubber by replacing the lower rack and adding an upper rack and slides. A spindle rack may be used in a SteamScrubber, though drying will be less efficient.
The SteamScrubber Racks
The SteamScrubber is equipped with a top rack and a bottom rack. Both racks are designed to accommodate inserts that hold flasks, beakers, culture tubes, graduated cylinders, Erlenmeyer flasks, petri dishes, watch glasses, BOD bottles, and a variety of other laboratory glassware. These inserts are sold separately and are detailed in Appendix A.

Product Service 1-800-522-7658

23

Chapter 4: Using Your Washer
Removing the Upper Rack
The upper rack may be easily removed from the Glassware Washer to facilitate loading the rack outside the washer or to allow very tall glassware to be loaded and washed on the lower rack.

To remove the upper rack:
1. Slide the upper rack all the way out of the washer. 2. Grasp each side of the rack placing a thumb on the release buttons. 3. Press each release button and lift the rack straight upward.
To install the upper rack:
1. The upper rack can be replaced into the washer by first sliding each slide rail all the way out of the washer and then lowering the rack onto the rails.
2. Press down and the latch will automatically engage the rail.
The FlaskScrubber Spindle Rack
The FlaskScrubber Glassware Washer is equipped with a lower spindle rack and glassware holders. The FlaskScrubber spindle rack is designed for narrow- necked glassware such as volumetric flasks, Erlenmeyer flasks, graduated cylinders, Kjeldahl flasks, test tubes, and digestion tubes.

24

Product Service 1-800-522-7658

Chapter 4: Using Your Washer
Two sizes of spindles are provided with the washer: thirty-six .25″ (6.35 mm) OD and ten .125″ (3.18mm) OD spindles. The optional Forty-Eight Pin Insert (Labconco P/N 4591601) may be positioned directly over spindles or spindles can be removed with a screw driver and replaced with the plugs included with the washer.
Optional top racks are available for the FlaskScrubber to expand the washer’s capacity to accommodate many types of glassware. An Upper Spindle Rack (Labconco P/N 4595600) is available with 30 spindles.
Loading Glassware into the FlaskScrubber
Glassware Holders are supplied with each FlaskScrubber. These holders enable you to position glassware onto the FlaskScrubber spindles.

SPRING CLIP TABS

To use a Glassware Holder:
1. Press the glassware into the holder; the clamps should spring out and grip the glassware. Note: It is normal for the clamps to deform if large glassware is inserted into the Holder and the washer is operated at high temperature. Do not use with glassware over 2.5 inches in diameter as damage to holder may occur.
2. The holder may be raised or lowered by squeezing the spring clip on the bottom of the holder and then sliding the holder up or down.
3. For best results, do not allow the glassware to rest directly on top of the spindle.

Product Service 1-800-522-7658

25

Chapter 4: Using Your Washer Glassware should be loaded so that it does not touch during a wash cycle. The washer has been designed for quiet operation. To prevent noise and glass breakage, be certain that glassware is retained.
The Detergent Dispenser
Your Glassware Washer is equipped with a detergent dispenser that contains a main wash cavity and a neutralizing solution port, as shown below. In addition, the washer door has a depression where detergent may be added for use during the first wash of the cycle.
Neutralizing solution dispenser cover
Main wash cavity
Neutralizing solution port
Neutralizing solution dial

The detergent dispenser opens during the second wash cycle, except when the Plastic cycle is selected, which has only one wash cycle. If your glassware is heavily soiled, you may want to add powder detergent to the depression in the washer door. Do not use liquid detergent in the pre-wash cavity in the washer door. The initial drain and fill cycle flushes the liquid detergent out of the washer prior to the first wash. Refer to the table below to determine which cavities to fill, based on the selected wash choice. You may use either the pre-wash cavity stamped in the washer door or the one on the lid of the detergent cup.

Wash Cycle Rinse Only Plastic All other cycles

Fill Pre-wash Cavity NO NO
OPTIONAL

Fill Main Cavity NO YES YES

!

Do not use combustible solvents in the Glassware Washer. If soiled glassware contains flammable compounds, rinse the

glassware thoroughly prior to placing the glassware into the

washer. Heaters in the washer are very hot and could ignite

flammable solvents.

26

Product Service 1-800-522-7658

Chapter 4: Using Your Washer

!

Petroleum based compounds may degrade certain internal washer components. Always thoroughly rinse petroleum based

compounds from glassware before placing in the Washer.

Non-foaming powder or liquid detergent formulated for labware washers, in conjunction with adequate hot water, is essential for clean glassware. Labconco LabSolutions Detergents are recommended. See Appendix A for ordering information. Use detergents sparingly. Too much detergent, particularly with softened water may cause etching of the glassware. This appears as a permanent cloudy film on the glassware.

Fill the main detergent cavity three-fourths full if the water hardness grains per gallon (GPG) for your water measures 0-4 GPG (soft water). Fill the detergent cavity completely if your water measures 4 GPG or higher (medium to hard water). If you use the pre-wash cavity stamped in the washer door, fill it completely.

Note: To open the detergent dispenser, gently slide the white tab sideways. The tab may break if it is pulled upward or perpendicular to the door.

Store detergent in a cool, dry place. Immediately replace the detergent container lid after dispensing. If lumps develop due to exposure to moisture, discard the detergent according to local regulations.

Filling the Neutralizing Acid Dispenser
A mild or weak acid may be dispensed from the neutralizing solution port to neutralize the detergent alkalinity. Labconco LabSolutions Neutralizing Acid Rinse is recommended. See Appendix A for ordering information. The neutralizing acid rinse is dispensed during the first rinse. To avoid dispensing neutralizing acid during a purified water rinse, the total rinses should be greater than the number of pure rinses. The dispenser holds approximately 170 ml and should be checked and replenished as needed. To fill the neutralizing acid dispenser, refer to the figure above and follow the instructions below.

Product Service 1-800-522-7658

27

Chapter 4: Using Your Washer
To fill the neutralizing acid dispenser:
1. Twist and pull up on the cap to remove the round cover on the neutralizing solution port.
2. Fill the cavity with LabSolutions Neutralizing Acid Rinse (Labconco P/N 4522200) 1M citric acid or 10% phosphoric acid until the level of the liquid rises and is visible in the port.
3. Set the dial to read 4 ml. 4. Replace the cover.
Selecting an Operating Cycle
The microprocessor control on your Glassware Washer allows you to select a factory programmed wash program, to modify the factory preset wash programs or to customize two additional programs. The control panel is shown below.

Programming and Starting a Wash Cycle
Refer to Appendix C: Glassware Washer Specifications for complete details on the various factory-set programs and the options available for customizing programs. After you have decided which washer program to use, follow the instructions below to start the washer.
Washers have the capability to wash glassware at high temperatures. Use care when selecting high-heat programs if plasticware is being washed.

28

Product Service 1-800-522-7658

Chapter 4: Using Your Washer
Any of the standard factory wash programs may be customized to suit specific wash requirements. All changes made to the programs will be stored in the washer microprocessor’s memory until it is changed again. If a FACTORY RESET is performed, all inputs entered by the user will be erased and the programs shipped with the washer will be reinstated. It is possible to customize the following program parameters:
Wash 2 temperature Wash 2 time Total number of rinses Number of purified water rinses Final rinse temperature Enable or disable the steam function Dry temperature Dry time
In addition, when USER 2 program is selected, it is possible to set:
Wash 1 time Rinse time (all rinses will be the same time)
To program and start a wash cycle:
1. Close the washer door and slide the latch to the right. This energizes the electronic control and the display will show the last program that was run.
2. Press RUN to select this program. 3. If a different program is desired, press DISPLAY. The available programs
will be shown on the display.

Product Service 1-800-522-7658

29

Chapter 4: Using Your Washer
4. Press the or buttons until the desired program is indicated by the arrow on the left side. The arrow on the lower right side means that there are additional program selections that will be shown on the display if the button is pressed. If an arrow is visible in the upper right corner of the display, additional program selections will be displayed when the button is pressed.
5. Press RUN if no modifications to the program are necessary. 6. If modifications to the program are necessary or you want to see the
parameters that are entered into the program, press DISPLAY and the elements in the program that may be altered will be displayed.

7. Press the and buttons to select the parameter that must be altered as indicated by the arrow on the left side. Press and buttons to select the appropriate set point. The arrow on the lower right side means that there are additional parameters selections that will be shown on the display if the button is pressed. If an arrow is visible in the upper right corner of the display, additional parameter selections will be displayed when the button is pressed.
8. Press RUN when all parameters are satisfactory.
Program Lock
After a program is selected and program parameters have been set, it is possible to lock those parameters into memory so they will not be inadvertently revised. This is done by first, entering the SELECT PROGRM screen. Then scroll down and select the program that will be locked. Press the display key two times to display that program, then press and hold the DISPLAY key for 15 seconds. LOCK will be displayed in the lower right hand corner. As long as the program is locked, only that one program may be run. Lock is released by pressing and holding DISPLAY for 15 seconds.

30

Product Service 1-800-522-7658

Chapter 4: Using Your Washer
Interrupting a Wash Cycle
To temporarily pause a wash cycle, simply unlatch the washer door. After the door is unlatched, wait 4 to 5 seconds before opening the door to prevent water from splashing out of the washer.

To resume the wash cycle, close and re-latch the washer door. The washer will pause to equalize temperatures and then the cycle will resume the interrupted segment.
The wash cycle can be terminated at any time by pressing the Start/Cancel button.
Alarms
Throughout a wash cycle there are several abnormal events that could occur. The washer is programmed to monitor these occurrences and provide an alarm to alert the operator. Information is shown on the display to identify the alarm situation. The following messages may be displayed. Certain alarm situations are signaled with an audible sound which self cancels after 1 minute.
HOT GLASS This displays at the end of a cycle if the temperature inside the washer is over 122°F (50°C). The alarm cancels when the temperature cools.
PLEASE WAIT This displays if the door is opened and then closed during a wash or rinse segment of a cycle. The display will also show the time remaining until the operation of the washer will resume where it was interrupted.
WATER LOW This displays if a water fill is inadequate. The washer will cancel the cycle and drain water that is in the washer. The alarm is canceled by opening the door. See Chapter 7: Troubleshooting ­ Washer will not fill.

Product Service 1-800-522-7658

31

Chapter 4: Using Your Washer
OVERFLOW This displays if water is detected in the base of the washer. Water fill valves will be closed and the washer will cancel the cycle and drain water that is in the washer. The alarm is canceled by opening the door. See Chapter 7: Troubleshooting ­ Washer leaks.
LIQ DETER This displays only if the optional liquid detergent dispenser is installed and the level of the detergent in the dispense container is low. The alarm is disabled if the detergent dispense volume is set to “0.” The alarm is canceled when detergent is added to the container.
DRAIN FAIL This displays if water fails to completely drain during a normal drain operation. Operation of the washer is canceled. The alarm is canceled by opening the door.
LOW TEMP This displays if the water doesn’t reach the set point temperature within 135 minutes. Operation of the washer continues. The alarm cancels when the door is opened.
TEMP SENSOR This displays if the temperature sensor is disconnected. It is canceled by connecting an operable sensor.

32

Product Service 1-800-522-7658

CHAPTER 5

MAINTAINING YOUR WASHER

Under normal operation, your Glassware Washer will require little routine maintenance to keep it functioning properly.
Maintaining the Stainless Steel Interior
The interior of your Glassware Washer is type 304 stainless steel. Never use metal scouring pads on the stainless steel interior. Metal scouring pads can scratch or leave metal chips that will rust.

To maintain the appearance and quality of the stainless steel interior, perform the following tasks as needed:

Wipe the outer edges on the inside door panel to remove particles and residue that occur during loading.
Use a sponge sprinkled with non-abrasive stainless steel cleaner to gently wipe the washer tank and door to remove surface discoloration caused by exposure to halogenated compounds or steel parts. In some cases, the finish may be slightly dulled by this action.

If your water has a high mineral content, film or spots may develop on the washer interior. If the procedures listed above do not eliminate the film or spots, you may run your washer through the special cycle below.

To remove film or spots from the washer interior:

1. Remove all glassware from the washer. 2. Choose the Glass Program, Steam OFF, Pure Rinse OFF, and set the drying
time to zero. 3. After the first fill is complete, open the washer and carefully pour one cup of
bleach into the bottom of the tank.

Product Service 1-800-522-7658

33

Chapter 5: Maintaining Your Washer
4. Close the washer door and allow the unit to wash and drain. 5. When the washer fills the second time, open the washer and add two cups of
4-8% acetic acid (or white vinegar) to the bottom of the tank. 6. Close the washer door and allow the unit to wash and drain without further
interruption.
Maintaining the Air Gap in Drain
If the installation included an air gap (recommended) it requires periodic cleaning. The air gap is not part of the washer; therefore, it is not covered by the washer warranty. The air gap protects the washer against water backing up in the event of a clogged drain. Check the air gap for build-up any time your washer is not draining well.
Most types of air gaps are easy to clean. Simply follow the manufacturer’s directions for maintaining your air gap.
Maintaining the Water Fill Valve
The filter screen of the water fill valve, illustrated below, may require periodic cleaning to remove trapped particles. A low water fill occurs if the blockage is not removed.

To clean the water fill valve:
1. Turn off the water and electrical power to the washer. Unplug the Mobile model; turn off the circuit breaker that services the Undercounter or Freestanding model.
2. Remove the rear panel of FreeStanding models. 3. Disconnect the water supply tube that is connected to the valve. 4. Remove the valve from the base. 5. Remove the four screws from the valve plate and separate the valve from the
inlet connection. 6. Remove the valve filter screen and clean it under running water.

34

Product Service 1-800-522-7658

Chapter 5: Maintaining Your Washer
7. Replace the screen and reassemble the valve connection. Be certain the O-ring gasket is positioned in the groove in the fill valve body.
Removing the Washer Top, Back, and Side Panels
There may be times when you need to remove the washer top, back, and side panels to clean, maintain, or repair your washer. Refer to the figure below and follow the instructions to remove the top, back, and side panels of your washer.
To remove the washer top, back, and side panels:
1. Turn off electrical power to the Glassware Washer. 2. Remove all of the screws from the back panel of the washer and remove the
back panel. 3. Remove the 2 screws at the kick panel. 4. Remove 2 screws at the rear that hold the sides to the top. 5. Remove the two screws from each side of the washer at the front edge. 6. Remove the side panels. 7. Remove the 2 screws that hold the top. 8. Remove the top.

Product Service 1-800-522-7658

35

Chapter 5: Maintaining Your Washer
Cleaning the Sump Filter Screen
If debris accumulates on the filter screen that is located in the washer sump, you can remove and clean the screen. To clean the sump filter screen, refer to the figure below and follow the instructions below.
To clean the sump filter screen:
1. Open the washer door and remove the bottom rack. 2. Remove the screw that retains the filter screen. 3. Carefully lift the screen and pull forward, using care not to drop debris into
the sump.

36

Product Service 1-800-522-7658

CHAPTER 6

MODIFYING YOUR WASHER

The configuration of your washer may be changed to accommodate your needs. For example, you may want to install pipet inserts, install an optional top rack, or install an optional liquid detergent dispense system or Cool Drain Water Kit. Refer to Appendix A: Glassware Washer Accessories for the accessories that are available for your Glassware Washer.
Adjusting the Height of the Upper Rack
The height of the upper rack may be varied to suit the heights of glassware that will be washed in the upper and lower racks.

Product Service 1-800-522-7658

37

Chapter 6: Modifying Your Washer
To adjust the height of the upper rack:
1. Remove the upper rack as described in Chapter 4: Using Your Washer. 2. Remove the 2 nuts that retain the rack mounting plate to the slide. 3. Reposition the rack mounting plate to the slide using the other set of holes.
Replace the 2 nuts. 4. Repeat the procedure on the opposite slide.
Spindle Rack Options
If you purchased a FlaskScrubber Glassware Washer, you can modify the configuration of your washer to better suit your needs. Optional accessories include two Pipet Inserts, and an Upper Spindle Rack. The Pipet Inserts are easily installed in place of one or more spindles in the washer and are designed to accommodate 1 ml to 50 ml pipets.
Installing Optional Pipet Inserts in a FlaskScrubber
Two sizes of Pipet Inserts are available. The 8-place Pipet Insert, shown below accommodates 1 ml to 10 ml pipets. Multiple Pipet Inserts may be installed, if desired. Refer to the figure and follow the instructions below to install an 8-place Pipet Insert.
To install an 8-place Pipet Insert:
1. Insert the tool supplied with the Spindle Rack or a screwdriver into the top of a spindle and turn counterclockwise to remove the spindle.
2. In the position previously occupied by the spindle, thread into place the short spindle you received with the Pipet Insert.
3. Push the Pipet Insert over the short spindle. 4. If spindles other than the one used for the short spindle are removed, the holes
must be plugged with the plastic plugs supplied with the spindle rack.

38

Product Service 1-800-522-7658

Chapter 6: Modifying Your Washer
The 16-place Pipet Insert, shown below accommodates 1 ml to 50 ml pipets. Two of these inserts may be installed, if desired. Refer to the figure and follow the instructions below to install a 16-place Pipet Insert.
To install a 16-place Pipet Insert:
1. Use the tool supplied with the Spindle Rack or a screwdriver to remove the six spindles on either the right or left side of the spindle rack. Remove others if necessary.
2. Replace the six spindles with the six short spindles that you received with the Pipet Insert.
3. Replace all other spindles with the plastic plugs that you received with your washer.
4. With the support facing the center of the spindle rack, slide the Pipet Insert over the spindles until it completely seats.
5. Push pipets into the 16 receptacles and rest them on the support.

Note: Lower spindle racks are shipped with 34 long spindles and 2 shorter spindles. If spindles are removed and then replaced, the shorter spindles should be located on the front row in the second and third positions from the right side. This will allow proper function of the detergent dispenser.

Product Service 1-800-522-7658

39

Chapter 6: Modifying Your Washer
Installing the Optional Upper Spindle Rack
The Upper Spindle Rack expands the capability of the FlaskScrubber by providing 30 additional spindles for washing narrow-neck glassware. The rack may be customized by removing spindles or by installing Multi-Pin Inserts which hold beakers or other wide mouth glassware.
To install the optional Upper Spindle Rack:
Install the upper rails and the upper spindle rack. See the figure below.
1. Remove the acorn nuts and lockwashers from both upper sides using a 3/8″ wrench. There are 4 on each side.

2. Position brackets on slides over the studs on the sides. The position of the rack mounting plates must be as shown. Secure the slide assemblies using lockwashers and acorn nuts removed in Step 1. It may be necessary to synchronize the travel of the two slides. Pull each slide out firmly to their maximum travel.

40

Product Service 1-800-522-7658

Chapter 6: Modifying Your Washer

3. Install the Upper Spindle Rack by lowering the rack onto the rack mounting plates. The water inlet must have its inlet toward the rear. Make sure the latch on each side secures the rack to the rack mounting plate.
When the Upper Spindle Rack is in place, it limits the height of the glassware that can be washed. If very tall glassware or long pipets are to be washed, remove the Upper Spindle Rack.
Installing Optional Inserts into the Spindle Rack
A Multi-Pin insert is available that can be placed directly on the FlaskScrubber upper or lower spindle rack. It can hold beakers or wide mouth glassware. The insert can be positioned either on the left side or right side.
To install an insert:
1. Remove all glassware, spring retainers and glassware holders. 2. Lower the insert down over the spindles. If necessary, spindles may be
removed using the tool supplied with the Spindle Rack or a screwdriver in the slot on the top of the spindles. Be sure to replace any removed spindle with a plug supplied.

Product Service 1-800-522-7658

41

Chapter 6: Modifying Your Washer
Installing Small Spindles
Ten small spindles are included with each Spindle Rack. Since the large volume of water which flows through the standard spindles may be great enough to force the glassware off the spindle, small spindles should be used when small pieces of glassware will be washed.
To install small spindles:
1. Remove the standard spindle by inserting the tool supplied with the Spindle Rack or a screwdriver into the slot on the top and turning counterclockwise.
2. Replace the standard spindle with a small spindle.
Installing the Optional Cool Drain Water Kit
An optional Cool Drain Water Kit is available to reduce the water temperature of the drain water in installations where hot drain water is not permitted. It may be installed on Undercounter or Freestanding models. A supply of cold water must be available. It is recommended that the cold water temperature is colder than 54°F (12°C). Warmer water temperature will cause the drain temperature to be higher. The cold water supply must be capable of a flow rate of 3.5 GPM (13.2 LPM) and a pressure of 20-120 PSI (138-827 kPa). Hot drain water will be mixed with cold water during drain operations. To install the optional Cool Drain Water Kit, refer to the figure below and the following instructions.
To install the optional Cool Drain Water Kit:
1. Disconnect power to the washer. 2. Remove the back panel of the washer if it is a Freestanding model or the cover
panel of an Undercounter model. 3. Attach the water valve assembly to the rear flange of the base using the screws
provided. 4. Connect the wires coming from the water valve assembly to the mating
connector in the wiring harness of the washer. 5. Connect the cold water supply to the water valve assembly. Do not allow the
tube to kink when the washer is placed into its operational location. If necessary, replace the straight fitting on the cool water valve with the supplied elbow. 6. Replace the back panel if it is a Freestanding model or the cover panel if it is an Undercounter model. 7. Attach the hose from the valve to a Twin Inlet High Flow Air-gap suitable for dishwasher applications. This may be obtained from a plumbing supply store. 8. Attach the drain hose from the Glassware Washer to the other inlet of the Airgap. 9. Attach the Air-gap to the building drain. 10. Turn on the electrical power.

42

Product Service 1-800-522-7658

Chapter 6: Modifying Your Washer

Installing the Optional Liquid Detergent Dispenser
An optional liquid detergent dispenser is available for installation on SteamScrubbers and FlaskScrubbers. This permits dispensing liquid detergent from a bulk 1 gallon (3.8 L) container eliminating the need to fill the detergent cup with detergent each time the washer is used. To install the liquid detergent dispenser, refer to the figures below and the following instructions.
To install the liquid detergent dispenser components:
1. Disconnect power to the washer. 2. Remove the back panel if the washer is a Freestanding model. Loosen the
insulation blanket to provide access to the back of the washer. 3. Attach the dispense pump to the rear flange of the base using the screws and
nuts provided. 4. Attach the tube from the detergent container to the inlet of the pump. 5. Route the tube from the pump outlet to the vacuum break on the right hand
side of the washer. Connect the tube to the .12 barb fitting on the side of the vacuum break. Secure the provided tie wrap around all 3 tubes on the top of the vacuum break being careful not to collapse any tube. 6. Locate the detergent container at a convenient location where it will not be a trip hazard. 7. Remove the lower panel and the electrical junction box cover as described in Chapter 3: Getting Started.

Product Service 1-800-522-7658

43

Chapter 6: Modifying Your Washer
8. Plug the supplied harness into terminal J6 on the Relay PCB and route the other end to the left rear corner of the washer base.
9. Plug the wire from the detergent container to the mating connector in the new harness in the base of the washer.
10. Plug the connectors on the pump to the mating connectors in the new harness in the base of the washer.
11. Reinstall the junction box cover and lower panel. 12. Reinstall the back panel if the washer is a Freestanding model. 13. Turn on the electrical power.

Enable the liquid detergent dispenser operation:

1. Enter the washer set up screen on the display by holding the button on the
control panel and closing the door and sliding the door latch to the right. 2. Press the button until the arrow on the left points to LIQ DETERGENT OPT. 3. Press the or button to activate this accessory.
4. Press RUN to save all settings.

Using the liquid detergent dispenser:

1. Remove the cap from the container and remove the tube and level switch assembly. 2. Fill the container with detergent or use a new bottle of Labconco detergent
and replace the tube and switch assembly and the cap. 3. There are two methods which can be followed for filling the system with detergent.
a. Run a wash cycle with no glassware in the washer. Set the detergent dispense rate to 30 ml.
b. Run a diagnostics test. When the display window shows DETERGENT PUMP, allow the pump to run for 30 seconds.
4. Program the quantity of detergent that will be dispensed by entering the programming screen as described in Chapter 4: Using Your Washer.

44

Product Service 1-800-522-7658

CHAPTER 7

TROUBLESHOOTING

Refer to the following table if your Glassware Washer fails to operate properly. If the suggested corrective actions do not solve your problem, contact Labconco Product Service for additional assistance.

PROBLEM

CAUSE

CORRECTIVE ACTION

Detergent cup fails Malfunction of cup to open

Replace cup.

Malfunction of relay Check electrical continuity or replace PCB.

Glassware interfering Move glassware. with cup door

Noises during operation

Glassware rattling

Load glassware properly. Do not allow glassware to touch.

Door panel vibrating Tighten panel screws.

Wash arms hitting

Check glassware loading.

Water inlet line makes occasional hammering sound

Check with plumber.

Purified water pump is activated

No corrective action needed. This is normal for about 5 minutes while pure water enters the washer.

Door drops too far Bent door hinge (below door stop)

Replace door hinge.

Product Service 1-800-522-7658

45

Chapter 7: Troubleshooting

PROBLEM
Poor drying
Poor washing results
Not draining properly
46

CAUSE

CORRECTIVE ACTION

Dry temperature too low Program warmer dry temperature.

Flask, beaker, or labware Tilt these articles when loading so that water with concave bottoms drains off. not loaded correctly

Recondensation

If clean labware is left in the washer, recondensation may occur. Open latch after completion of cycle to allow moisture-laden air to escape.

Heater(s) disconnected or malfunctioned

Reconnect or replace heater.

Blower disconnected or Reconnect or replace blower. malfunctioned

Dry time too short

Program longer time.

Temperature sensor out of calibration

Verify displayed temperature by attaching a thermocouple to the temperature sensor. Route leads outside of the washer. Close and latch the door while holding the button. Call Labconco Product Services if the displayed temperature differs from the test temperature by more than ±4°C.

Water is not hot enough

Check Wash 2 water temperature. Must be at least 120°F (49°C). Recommended temperature is 150°F (66°C).

Improper loading

Check washer loading instructions in Chapter 4 in this manual.

Detergent too old or amount wrong

Replace detergent or change quantity used.

Detergent caked in cup

Clean cup. Replace with fresh detergent. Check water inlet temperature. Must be at least 120°F (49°C).

Insufficient wash time Increase wash cycle time.

Insufficient water

Check to be sure the water shut-off valve is fully open. Check to be sure the water pressure is between 20 and 120 psi (138-827 kPa) at a flow rate of 1.25 (4.7 Liters/min) gallons per minute. Check water level switch.

Clogged filter

Clean sump filter.

Drain line clogged or kinked

Disconnect drain line and clean or remove kink.

Product Service 1-800-522-7658

Chapter 7: Troubleshooting

PROBLEM

CAUSE

CORRECTIVE ACTION

Purified water does Crimp in supply hose Refer to installation instructions for proper

not fill

purified water piping installation.

Motor wires disconnected

Reconnect wires.

Tank and inner door have surface rust

Collects normally

Clean with stainless steel cleaner and soft cloth.

Glassware is contaminated with mineral acids.

Pre-rinse glassware. Clean with stainless steel cleaner and soft cloth.

Washer does not run

No power to washer Check fuse or circuit breaker, or door switch.

Door latch is open

Latch washer door by pushing door in.

Washer door opens Cabinet opening is not Correct opening with leveling feet.

and closes badly

square

Door hitting counter- Adjust mounting screws. top mounting screws

Washer leaks

Washer is not level

Adjust leveling feet.

Door not sealing

Adjust door latch.

Tank gasket loose

Check gasket and correct.

Loose connection at hose clamps

Tighten hose clamp.

Loose connection at fill valve

Check fill valve and correct.

Improper detergent

Use non-foaming detergent. Use only proper amount of detergent.

Obstruction in drain line

Remove obstruction.

Washer overfilling

Check operation of fill switch.

Washer leaks around door seal

Improper installation

Check cabinet opening to see if it is aligned properly with the door. Washer must be level. Adjust feet to level unit.

Unit not level

Adjust feet to level unit.

Door opened during operation

Allow 4-5 seconds before opening door after unlatching.

Product Service 1-800-522-7658

47

Chapter 7: Troubleshooting

PROBLEM
Washer will not drain
Washer will not fill
Washer overfills Selection buttons on control panel inoperable or controls malfunction Drain Fail Alarm
48

CAUSE

CORRECTIVE ACTION

Clogged drain

Clean out drain.

Blockage of air gap

Clean the air gap by lifting the cover, unscrewing the cap, and removing any accumulated material. See Chapter 5.

Kink in drain hose Check for a kink in the drain hose.

Filter blocked

Check filter in washer and clean as needed.

Drain valve or pump Check operation. not operating

Fill valve clogged

Clean fill valve.

Water supply turned Turn on water. off

Defective fill switch Defective fill switch Microprocessor memory error
Key pad defective Drain Valve inoperable

Check operation.
Check operation.
Perform “Factory Reset.” Open latch on door. Press button and simultaneously close door latch. Release button and display will show the set up screen. Press until FACTORY RESET is highlighted. Press or until “Yes” is displayed. Press RUN.
Replace key pad.
Listen for click when washer should drain.

Drain Pump inoperable

Check for mechanical restriction of actuator arm on top of valve.
Check for electrical power to valve.
Check for damage to valve coil.
Check if pump fan turns when washer should drain.

Check for mechanical restriction of fan.

Check for electrical power to pump.

Drain hose not routed Hose from drain pump must slope upward and

properly

have no low spots or horizontal runs under

washer tank.

Make sure hose is attached to the back of the washer and has a high loop.

Product Service 1-800-522-7658

Chapter 7: Troubleshooting

PROBLEM

CAUSE

CORRECTIVE ACTION

Drain hose not routed Hose must be attached to building plumbing pipe

properly (cont.)

¾ inch ID or larger.

Hose from washer must not be attached to another hose.

Check for kinks in hose.

Drain hose must not be elevated more than 30 inches.

Pump lost its prime

Remove ALL water from inside drain hose. Pump will prime when water drains from washer.

Building plumbing defective

Check for blocked air gap.

Check for clogged drain.

Filter screen clogged Clean screen in bottom of washer.

Defective fill level switch

Contact Labconco Product Service.

Defective controller Check output from PCB to drain valve and pump.

Replace PCB. Contact Labconco Product Service.

Water Low Alarm Improper water supply

Make sure water is turned on.

Tap water pressure must be at least 20 psi (138 kPa) and flow must be at least 1.25 gallons (4.7 liters)/minute.

DI water supply must have flow of at least 0.9 gallons (3.4 liter)/minute.

Improper water supply (cont.)

At least 3.4 gallons (13 liters) must be available for each DI rinse.

Defective fill valves Clean screens inside the inlet fittings of the water valves.

Check voltage to valves.

Replace valve if it does not operate.

Restricted flow

Check for kinks in water hoses in base of washer to water inlet fitting on side of tank.

Defective DI water pump

Check voltage at pump.

Listen for pump operation. Replace if necessary.

Product Service 1-800-522-7658

49

Chapter 7: Troubleshooting

PROBLEM
Low Temp Alarm

CAUSE

CORRECTIVE ACTION

Defective hose to fill Check for splits. switch

Check for loose clamps.

Defective fill level switch

Recalibrate switch. Contact Labconco Product Service.

Replace switch.

Defective controller Check output from PCB to both valves and DI pump.

Replace PCB. Contact Labconco Product Service.

Holes in filter screen Contact Labconco Product Service. too small

Defective grommet where hose connects to fill level switch

Replace grommet.

Heater inoperative Check electrical connections.

Check voltage to heater.

Check resistance of heater. If open circuit, replace heater.

Defective controller Check output from PCB to heater.

Replace PCB. Contact Labconco Product Service.

Defective temperature probe

Check electrical connections.

Contact Labconco Product Service. Replace if necessary.

Defective high temperature cut out switch

Check resistance of safety cut out switch. If open circuit at room temperature, replace switch.

50

Product Service 1-800-522-7658

APPENDIX A

GLASSWARE WASHER ACCESSORIES

FlaskScrubber Accessories

PART # DESCRIPTION

4595600

Upper Spindle Rack ­ Stainless Steel. Contains one upper spindle rack with 30 spindles, 30 glassware clips, 15 plastic glassware holders and 2 slides.

4595800 Same as above except without slides.

4494200 8-Place Pipet Washer ­ Stainless Steel. Holds
1 ml to 10 ml pipets.

Product Service 1-800-522-7658

51

Appendix A: Glassware Washer Accessories
PART # DESCRIPTION
4595200 16-Place Pipet Washer ­ Stainless Steel. Holds 1 ml to 50 ml pipets.

4424600 4424800

Glassware Holder ­ Small. Grips wide-mouth glassware over spindles. Vinyl coated stainless steel wires.

Glassware Holder ­ Large. Grips wide-mouth glassware over spindles. Vinyl coated stainless steel wires.

4596000

Small Spindles with Clips. Replaces larger spindles when washing small glassware. 10 spindles, 10 clips, 36 plugs.

4595700

Lower Spindle Rack ­ Stainless Steel. Contains 36 spindles, 18 plastic glassware holders and 36 glassware clips. Included with FlaskScrubbers.

52

Product Service 1-800-522-7658

Appendix A: Glassware Washer Accessories

FlaskScrubber or SteamScrubber Accessories

PART # DESCRIPTION

4402001

Culture Tube/Test Tube Insert ­ Stainless Steel. Insert for 15 mm to 18
mm tubes.

4402101

Culture Tube/Test Tube Insert ­ Stainless Steel. Insert for 20 mm to 25
mm tubes.

4401301

Culture tube/Test Tube Insert ­ Stainless Steel. Insert for 10 mm to 12 mm tubes. Includes retainer top 4401401.

4401401

Retainer Top for Culture Tube Insert ­ Stainless Steel. For use with all culture tube inserts to keep lightweight tubes in place under water pressure.

4401501

10-Pin Insert ­ Stainless Steel. For use with beakers, Erlenmeyer flasks, and other widemouth glassware.

Product Service 1-800-522-7658

53

Appendix A: Glassware Washer Accessories

PART # DESCRIPTION

4401801

32-Pin Insert ­ Stainless Steel. For use with beakers, Erlenmeyer flasks, and other widemouth glassware.

4401901

Retainer Top ­ Stainless Steel. To keep lightweight flasks in place under water pressure. For use with 4401801 or 4401501.

4589701

Petri Dish Insert ­ Stainless Steel. For plates, petri dishes, and watch glasses.

4589201

BOD Rack/Beaker/ Erlenmeyer Flask Insert ­ Stainless Steel. Rack secures glassware used in oxygen-demand determination, beakers, and Erlenmeyer flasks.

4598401 Tray Holder. For trays up to 19 x 19 x 2.5 deep (48 x 48 x 6 cm deep)

54

Product Service 1-800-522-7658

Appendix A: Glassware Washer Accessories

PART # DESCRIPTION

4402201

Utensil Basket ­ Stainless Steel. For miscellaneous labware such as stoppers, spatulas, small beakers, etc. Furnished with drop-in cover (part number 4493801).

4591601

48-Pin Insert ­ Stainless Steel. For use with beakers, Erlenmeyer flasks, and wide-mouth glassware. For placement in bottom or upper rack.

4587000

Top Rack ­ Stainless Steel. Included with
SteamScrubbers.

4595900

Top Rack ­ Stainless Steel. Includes 2 slides for
installation in FlaskSrubber.

Product Service 1-800-522-7658

55

Appendix A: Glassware Washer Accessories
PART # DESCRIPTION
4588500 Bottom Rack ­ Stainless Steel. Included with SteamScrubber.

4591500

DNA Sequencing Plate Insert. For electrophoresis plates 10.0 x 16.6 inches (25.4 x 42.1 cm). Holds 6 plates.

4542500 Utensil Holder. For spatulas, spoons, scoops & miscellaneous utensils.

56

Product Service 1-800-522-7658

Appendix A: Glassware Washer Accessories
PART # DESCRIPTION
4542100 Bulk Tube Insert. For vertically positioning test tubes.

4595400

Stand. For use with Freestanding models. Raises washer approximately 17 inches (43 cm). Front opens to provide storage underneath washer. Shown with glassware washer installed.

4591900 (115V)
4591901 (230V)

Cool Drain Water Drain Kit. Provides cool water to the drain plumbing. Connects to a cold water source.

4587500

Liquid Detergent Dispense Kit. Permits liquid detergent to be dispensed into the glassware washer directly from a 1 gallon container.

4596100 (115V)
4596101 (230V)

Mobile Conversion Kit. Permits a Freestanding Glassware Washer to be converted to a Mobile model. Includes casters, electrical cord and plug, and plumbing to connect to a sink faucet.

Product Service 1-800-522-7658

57

Appendix A: Glassware Washer Accessories
PART # DESCRIPTION
4592200 Connection Kit. DI Water inlet valve to plastic tubing.

1233700 Power Boost Transformer. For 208V operation.

4546000

Test Tube Spindle Rack. Lower rack with 150 spindles for washing test tubes 10mm to 25mm.

4546100 10-13mm Test Tube Holder. Holds 150 tubes. Used with Test Tube Spindle Rack
4546200 14-20mm Test Tube Holder. Holds 75 tubes. Used with Test Tube Spindle Rack
4526300 10-13mm Test Tube Holder. Holds 75 tubes. Used with Test Tube Spindle Rack

CONSUMABLES

PART #

DESCRIPTION

4422000 10-lb. (4.5 kg) LabSolutions Powder Detergent

4422100 27.5-lb. (12.5 kg) LabSolutions Powder Detergent

4522000 1 gallon (3.8 L) LabSolutions Liquid Detergent

4522200 1 liter (34 oz.) LabSolutions Neutralizing Acid Rinse

58

Product Service 1-800-522-7658

APPENDIX B
GLASSWARE WASHER DIMENSIONS
Freestanding Washer
Undercounter Washer

Product Service 1-800-522-7658

59

Appendix B: Glassware Washer Dimensions
Interior – All SteamScrubbers
Interior – All FlaskScrubbers

60

Product Service 1-800-522-7658

APPENDIX C
GLASSWARE WASHER SPECIFICATIONS
This Appendix contains various specifications for the Glassware Washer, including program times and water consumption for both the 115V and 230V models.
Glassware Washer Specifications
Minimum fill water temperature: 120°F (49°C) recommended Water consumption per fill: 3.4 gallons (13 liters) Minimum feed water pressure: 20 psi (138 kPa) Maximum feed water pressure: 120 psi (827 kPa) Minimum purified water feed pressure: 0 psi (0 kPa) Heat rejected from washer: less than 104 BTU/minute (115V models);
less than 170 BTU/minute (230V models) Water heating rate: 1.6°F/minute (0.9°C/minute) 115V models
operating on 115V; 2.2°F/minute (1.2°C/minute) 230V models operating on 208V
Electrical Specifications
Operating voltage for 115V washers: 104/127V Operating voltage for 230V washers: 207/253V Maximum amperage for 115 volt washers: 16.0 amperes Maximum amperage for 230 volt washers: 11.0 amperes Frequency 115 volt washers: 60 Hz Frequency 230 volt washers: 50/60 Hz Phase: Single Sump element power: 1,200 watts (115V models); 2,000 watts (230V
models)

Product Service 1-800-522-7658

61

Appendix C: Glassware Washer Specifications
Environmental Conditions
Indoor use only. Maximum altitude: 6562 feet (2000 meters). Ambient temperature range: 41° to 104°F (5° to 40°C). Maximum relative humidity: 80% for temperatures up to 88°F (31°C),
decreasing linearly to 50% relative humidity at 104°F (40°C). Main supply voltage fluctuations not to exceed ±10% of the nominal
voltage. Transient overvoltages according to Installation Categories II
(Overvoltage Categories per IEC 1010). Temporary voltage spikes on the AC input line that may be as high as 1500V for 115V models and 2500V for 230V models are allowed. Used in an environment of Pollution degrees 2 (i.e., where normally only non-conductive atmospheres are present). Occasionally, however, a temporary conductivity caused by condensation must be expected, in accordance with IEC 664.

62

Product Service 1-800-522-7658

Appendix C: Glassware Washer Specifications Program Times & Water Consumption (115V Models)

Product Service 1-800-522-7658

Factory Program Descriptions and Possible User Modifications- 115V Models

Delayed Start Wash 1 Time Steam Wash 2 Time Wash 2 Temp
Number of Rinses No of Pure Rinses Rinse Time Final Rinse Temp
Dry Time Dry Temp

Rinse Only

Plastic

Glass

Glass Plus

Science

Units

Factory

User set

Factory

User set

Factory

User set

Factory

User set

Factory

User set

(hours)

0

1 to 8

0

0 to 8

0

0 to 8

0

0 to 8

0

0 to 8

(minutes)

0

None

5

None

5

None

5

None

No

None

No

Yes / No

Yes

Yes / No

No

Yes / No

(minutes)

10

1 to 40

10

1 to 40

10

1 to 40

20

1 to 40

(°F)

122

100 to 140

140

100 to 180

140

100 to 180

158

100 to 180

(°C)

50

38-60

60

38-82

60

38-82

70

38-82

1

0 to 6

2

0 to 6

3

0 to 6

3

0 to 6

4

0 to 6

0

0 to 6

0

0 to 6

0

0 to 6

0

0 to 6

0

0 to 6

(minutes)

4

None

4

None

4

None

4

None

4

None

(°F)

100

100 to 140

122

100 to 140

140

100 to 180

140

100 to 180

140

100 to 180

(°C)

38

38 to 60

50

38 to 60

60

38 to 82

60

38 to 82

60

38 to 82

(minutes)

0

0 or 15 to 250 15

0 or 15 to 250

30

0 or 15 to 250

30

0 or 15 to 250

40 0 or 15 to 250

(°F)

100

100 to 140

122

100 to 140

140

100 to 158

140

100 to 158

140

100 to 158

(°C)

38

38 to 60

50

38 to 60

60

38 to 70

60

38 to 70

60

38 to 70

Total Water Consumption

(gallons) (liters)

3.4 12.9

3.4 to 20.4 12.9 to 77.2

13.6

6.8 to 27.2

17.0

6.8 to 27.2

17.0

51.5 25.7 to 103.0 64.4 25.7 to 103.0 64.4

6.8 to 27.2 25.7 to 103.0

20.4

6.8 to 27.2

77.2 25.7 to 103.0

Total Wash Time

(Excluding delays for

heating water and

dry time)

(min)

10

51

86

96

116

63

Note Times shown are for tap water rinses. Pure rinses add 1.5 minutes per rinse. Additional time is required to allow inlet water to heat up to the set temperature. Steam adds 10 minutes to the total program time.

Factory Program Descriptions and Possible User Modifications- 115V Models

Appendix C: Glassware Washer Specifications

64

Product Service 1-800-522-7658

Delayed Start Wash 1 Time Steam Wash 2 Time Wash 2 Temp
Number of Rinses No of Pure Rinses Rinse Time Final Rinse Temp
Dry Time Dry Temp

Science Plus

Dry Only

User 1

User 2

Units

Factory

User set

Factory

User set

Factory

User set

Factory

User set

(hours)

0

0 to 8

0

0 to 8

0

0 to 8

(minutes)

5

None

5

None

5

0 to 10

Yes

Yes / No

No

Yes / No

No

Yes / No

(minutes)

20

1 to 40

10

1 to 40

10

1 to 40

(°F)

158

100 to 180

(°C)

70

38-82

140

100 to 180

140

100 to 180

60

38-82

82

38-82

4

0 to 6

2

0 to 6

2

0 to 6

0

0 to 6

0

0 to 6

0

0 to 6

(minutes)

4

None

4

None

4

1 to 30

(°F)

140

100 to 180

(°C)

60

38 to 82

140

100 to 180

140

100 to 180

60

38 to 82

60

38 to 82

(minutes)

40 0 or 15 to 250 60

0 or 15 to 250

15

0 or 15 to 250

15 0 or 15 to 250

(°F)

140

100 to 158

140

100 to 158

140

100 to 158

140

100 to 158

(°C)

60

38 to 70

60

38 to 70

60

38 to 70

60

38 to 70

Total Water Consumption

(gallons) 20.4

6.8 to 27.2

0

(liters)

77.2 25.7 to 103.0

0

Total Wash Time

(Excluding delays for

heating water and

dry time)

(min)

126

60

0

13.6

6.8 to 27.2

13.6

6.8 to 27.2

0

51.5 25.7 to 103.0 51.5 25.7 to 103.0

62

62

Appendix C: Glassware Washer Specifications Program Times & Water Consumption (230V Models)

Product Service 1-800-522-7658

Factory Program Descriptions and Possible User Modifications- 230V Models

Rinse Only

Plastic

Glass

Glass Plus

Science

Science Plus

Units

Factory

User set

Factory

User set

Factory

User set

Factory

User set

Factory

User set

Factory

User set

Delayed Start

(hours)

0

0 to 8

0

0 to 8

0

0 to 8

0

0 to 8

0

0 to 8

Wash 1 Time

(minutes)

5

None

5

None

5

None

5

None

5

None

Steam

No

None

No

Yes/ No

Yes

Yes/ No

No

Yes/ No

Yes

Yes/ No

Wash 2 Time

(minutes)

10

1 to 40

10

1 to 40

10

1 to 40

20

1 to 40

20

1 to 40

Wash 2 Temperature

(°F)

(°C)

122

100 to 140

140

100 to 199

140

100 to 199

158

100 to 199

158

100 to 199

50

38 to 60

60

38 to 93

60

38 to 93

70

38 to 93

70

38 to 93

Number of Rinses

1

0 to 6

2

0 to 6

3

0 to 6

3

0 to 6

4

0 to 6

4

0 to 6

No of Pure Rinses

0

0 to 6

0

0 to 6

0

0 to 6

0

0 to 6

0

0 to 6

0

0 to 6

Rinse Time

(minutes)

4

None

4

None

4

None

4

None

4

None

4

None

Final Rinse Temp

(°F)

100

100 to 140

122

100 to 140

140

100 to 199

140

100 to 199

158

100 to 199

158

100 to 199

(°C)

38

38 to 60

50

38 to 60

60

38 to 93

60

38 to 93

70

38 to 93

70

38 to 93

Dry Time

(minutes)

0

0 or 15 to 250 15

0 or 15 to 250

30

0 or 15 to 250

30

0 or 15 to 250

40

0 or 15 to 250

40

0 or 15 to 250

Dry Temperature

(°F)

100

100 to 140

122

100 to 140

140

100 to 158

140

100 to 158

140

100 to 158

140

100 to 158

(°C)

38

38 to 60

50

38 to 60

60

38 to 70

60

38 to 70

60

38 to 70

60

38 to 70

Total Water Consumption

(gallons)

3.4

3.4 to 20.4

13.6

6.8 to 27.2

17.0

6.8 to 27.2

17.0

6.8 to 27.2

20.4

6.8 to 27.2

20.4

6.8 to 27.2

(liters)

12.9 12.9 to 77.2 51.5 25.7 to 103.0 64.4 25.7 to 103.0 64.4 25.7 to 103.0 77.2 25.7 to 103.0 77.2 25.7 to 103.0

Total Wash Time

(Excluding delays for

heating water and dry

time)

(min)

10

51

86

96

116

126

Note Times shown are for tap water rinses. Pure rinses add 1.5 minutes per rinse. Additional time is required to allow inlet water to heat up to the set temperature. Steam adds 10 minutes to the total program time.

65

Appendix C: Glassware Washer Specifications

66

Factory Program Descriptions and Possible User Modifications- 230V Models

Intense

Intense Plus

Extreme

Dry Only

User 1

User 2

Units

Factory

User set

Factory

User set

Factory

User set

Factory

User set

Factory

User set

Factory

User set

Delayed Start

(hours)

0

0 to 8

0

0 to 8

0

0 to 8

0

0 to 8

0

0 to 8

Wash 1 Time

(minutes)

10

None

10

None

10

None

5

None

5

0 to 10

Steam

No

Yes/ No

Yes

Yes/ No

Yes

Yes/ No

No

Yes/ No

No

Yes/ No

Wash 2 Time

(minutes)

30

1 to 40

30

1 to 40

40

1 to 40

10

1 to 40

10

1 to 40

Wash 2 Temperature

(°F)

(°C)

180

100 to 199

180

100 to 199

199

100 to 199

82

38 to 93

82

38 to 93

93

38 to 93

140

100 to 199

180

100 to 199

60

38 to 93

82

38 to 93

Number of Rinses

5

0 to 6

5

0 to 6

6

0 to 6

2

0 to 6

2

0 to 6

No of Pure Rinses

0

0 to 6

0

0 to 6

0

0 to 6

0

0 to 6

0

0 to 6

Rinse Time

(minutes)

4

None

4

None

4

None

4

None

4

1 to 30

Final Rinse Temp

(°F)

180

100 to 199

180

100 to 199

199

100 to 199

(°C)

82

38 to 93

82

38 to 93

93

38 to 93

140

100 to 199

180

100 to 199

60

38 to 93

82

38 to 93

Dry Time

(minutes)

50

0 or 15 to 250

50

0 or 15 to 250

60

0 or 15 to 250

60

0 or 15 to 250

15

0 or 15 to 250

15

0 or 15 to 250

Dry Temperature

(°F)

140

100 to 158

140

100 to 158

140

100 to 158

140

100 to 158

140

100 to 158

140

100 to 158

(°C)

60

38 to 70

60

38 to 70

60

38 to 70

60

38 to 70

60

38 to 70

60

38 to 70

Total Water Consumption

(gallons)

23.8

6.8 to 27.2

23.8

6.8 to 27.2

27.2

6.8 to 27.2

0

(liters)

90.1 25.7 to 103.0 90.1 25.7 to 103.0 103.0 25.7 to 103.0

0

0

13.6

6.8 to 27.2

13.6

6.8 to 27.2

0

51.5 25.7 to 103.0 51.5 25.7 to 103.0

Total Wash Time

(Excluding delays for

heating water and dry

time)

(min)

150

160

190

60

62

62

Product Service 1-800-522-7658

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>