Flymo EasiGlide Plus 300V Electric Hover Lawnmower Owner’s Manual

: June 6, 2024
: Flymo

Table of Contents

SAFETY
ASSEMBLY INSTRUCTIONS
OPERATION
MAINTENANCE
STORAGE
TROUBLESHOOTING
TECHNICAL DATA
ACCESSORIES
SERVICE/WARRANTY
PRODUCT LIABILITY
EC DECLARATION OF CONFORMITY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Flymo EasiGlide Plus 300V Electric Hover Lawnmower Owner’s Manual

Original instructions.

This product may be used under supervision, or if instruction regarding the safe use of the product has been provided and the
resulting dangers have been understood, by children aged 8 and above, as well as by persons with physical, sensory or mental disabilities or a lack of experience and knowledge. Children must not be allowed to play with the product.
Cleaning and user maintenance must not be performed by children without supervision.
The use of this product by young people under the age of 16 is not recommended.

Intended use:
The FLYMO Lawnmower is intended to mow lawn in private domestic
gardens and allotments.

The product is not intended for long term use

DANGER! Risk of injury!

Do not use the product to cut bushes, hedges, shrubs, to cut of climbers or grass on roofs or balcony boxes, to chop up branches, twigs and to level irregularities in the soil. Do not use the product on a slope steeper than 20° maximum.

SAFETY

IMPORTANT!
Read the operator’s manual carefully before use and keep for future reference.

Symbols on the product:

Read operator’s manual.
Keep bystanders away.
Beware of sharp blades. Blades continue to rotate after the motor is switched off. Remove plug from mains before maintenance or if cord is damaged.
Keep the mains cable away from the cutting blades

General safety warnings

Electrical safety

DANGER! Electric shock!
Risk of injury due to electric shock.

The product must be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30 mA.

WARNING! Risk of physical injury!
Cut injury when the blade turns or the product starts accidentally.

Disconnect the product from the mains before you do maintenance or you replace parts. Thereby the disconnected socket must be in the visual range.

Cables
If extension cables are used, these must comply with the minimum crosssections in the table below:

Voltage	Cable length	Cross section
220 – 240 V / 50 Hz	Up to 40 m	1.0 mm²
220 – 240 V / 50 Hz	Up to 60 m	1.5 mm²
220 – 240 V / 50 Hz	Up to 100 m	2.5 mm²

Minimum rating: 1.0 mm² size cable, 10 amps 250 volts AC.

Your product is supplied with cable wired directly into the product.

If the supply cord is damaged, it must be replaced by your local Husqvarna UK Ltd. Approved Service Centre or similarly qualified persons in order to avoid a hazard.
Do not wire an extension cable directly to your product yourself. Please contact your local Husqvarna UK Ltd. Approved Service Centre for further information on the connectors and kits available.
Only use extension cables specifically designed for outdoor use and which conform to one of the following specifications: Ordinary rubber (60245 IEC 53), Ordinary PVC (60227 IEC 53) or Ordinary PCP (60245 IEC 57).

Training

Read the instructions carefully. Be familiar with the controls and the correct use of the machine.
Never allow children or people unfamiliar with these instructions to use the machine. Local regulations can restrict the age of the operator.
Never operate the machine while people, especially children, or pets are
nearby.
Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property

Preparation

While operating the machine always wear substantial footwear and long trousers. Do not operate the machine when barefoot or wearing open sandals. Avoid wearing clothing that is loose fitting or that hanging cords or ties.
Thoroughly inspect the area where the machine is to be used and remove all objects which can be thrown by the machine.
Before using, always visually inspect to see that the blade, blade bolt and the blade assembly are not worn or damaged. Replace worn or damaged components in set to preserve balance. Replace damaged or unreadable labels.
Before use check the supply and extension cord for signs of damage or
aging. If the cord becomes damaged during use, disconnect the cord from the supply immediately.
DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY. Do not use the machine if the cord is damaged or worn.

Operation

Operate the machine only in daylight or in good artificial light.
Avoid operating the machine in wet grass.
Always be sure of your footing on slopes.
Walk, never run.
Mow across the face of slopes, never up and down.
Exercise extreme caution when changing direction on slopes.
Do not mow excessively steep slopes.
Use extreme caution when reversing or pulling the machine towards you.
Stop the blade(s) if the machine has to be tilted for transportation when crossing surfaces other than grass, and when transporting the machine to and from area to be used.
Never operate the machine with defective guards or shields, or without safety devices, for example deflectors and/or grass collector, in place.
Switch on the motor carefully according to instructions and with feet well away from the blade(s).
Do not tilt the machine when switching on the motor, except if the machine has to be tilted for starting. In this case, do not tilt it more than absolutely necessary and lift only the part, which is away from the operator.
Do not start the machine when standing in front of the discharge opening.
Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.
Do not transport the machine while the power source is running.
Stop the machine, and remove plug from the socket. Make sure that all moving parts have come to a complete stop.
- whenever you leave the machine,
- before clearing blockages or unclogging chute,
- before checking, cleaning or working on the machine,
- after striking a foreign object. Inspect the machine for damage and make repairs before restarting and operating the machine;
  if the machine starts to vibrate abnormally (check immediately)
- inspect for damage,
- replace or repair any damaged parts,
- check for and tighten any loose parts.

Maintenance and storage

Keep all nuts, bolts, and screws tight to be sure the machine is in safe working condition.
Check the grass collector frequently for wear or deterioration.
Replace worn or damaged parts for safety.
On machines with multi blade, take care as rotating one blade can cause
other blades rotate.
Be careful during adjustment of the machine to prevent entrapment of the fingers between moving blades and fixed parts of the machine.
Always allow the machine to cool down before storing.
When servicing the blades be aware that, even though the power source is switched off, the blades can still be moved.
Use only genuine replacement parts and accessories.

Additional safety warnings

Electrical safety

DANGER! Cardiac arrest!
This product makes an electromagnetic field while it operates. This field may under some conditions interfere with active or passive medical implants. To decrease the risk of conditions that can possibly injure or kill, we recommend persons with medical implants to speak with their physician and the medical implant manufacturer before you operate the product.

Before use, examine the cable for signs of damage or ageing. If the cable is found to be defective, take the product to an authorised Service Centre and have the cable replaced.
Do not use the product if the electric cables are damaged or worn.
Immediately disconnect from the mains if the cable is cut, or the insulation is damaged. Do not touch the electric cable until the cable has been disconnected.
Do not repair a cut or damaged cable. Replace it with a new one.
The extension cable must be uncoiled. Coiled cables can overheat and reduce the efficiency of your mower.
Keep the extension cable away from product, always work away from the power point mowing up and down, never in circles.
Do not pull cable around sharp objects.
Always switch off at the mains before disconnecting any plug, cable connector or extension cable.
Stop the motor, disconnect the mains and examine the cable for damage or ageing before you wind the cable for storage. Do not repair a damaged cable, replace it with a new one. Use only genuine replacement cable.
Always wind the cable carefully, avoid kinking.
Do not carry the product by the cable.
Do not pull on the cable to disconnect any of the plugs.
Use only on AC mains supply voltage shown on the product rating label.
Our products are double insulated to EN60335. Do not connect an earth to any part of the product.
Check the working area for hidden cables.
Do not use for pond care or close to water.

Personal safety

DANGER! Risk of suffocation!
Small parts can be easily swallowed. There is also a risk that the polybag can suffocate toddlers. Keep toddlers away when you assemble the product.

Let the hover mower to cool down for at least 30 minutes before storage or maintenance.
If blockage of cutting element stop product and check.
Do not tilt the machine into the direction of the user.
Do not move backwards.
Stay alert during operation.
Do not use in explosive atmosphere.
Do not operate the product when you are tired, ill or under the influence of alcohol, drugs or medicine or you exhausted.
Do not overload the mower.
Use gloves, wear slip resistant shoes and wear eye protection.
Do not use under wet conditions.
Do not use on wet grass.
Do not disassemble the product further than the delivery status.
Only start the mower with an upright standing handle.
Do not use the start levers alternately.
Use the handles carefully.

Safety Cut-Out

The motor is protected by a Safety Cut-Out which is activated when the blade
becomes jammed or if the motor is overloaded. When this occurs, stop and disconnect the product from the mains. The Safety Cut-Out will only reset when you release the start/ stop lever. Clear any obstruction and wait for a few minutes for the Safety Cut-Out to reset before you continue to use the product.

ASSEMBLY INSTRUCTIONS

DANGER! Risk of injury!
Cut injury when the product starts accidentally.
Wait for the blade to stop, disconnect the product from the mains and use gloves before you assemble the product.

To lift the handle in operation position [Fig. A1]:
The product is supplied with the upper handle folded over the product for packing and transportation.

Lift the upper handle (1).
Do not drop the handle.
Make sure that the cable does not become trapped between the handles.

To assemble the handle [Fig. A2/A3/A4]:

Fit the bolts (8), the washers (7) and the mains cable hooks (H) onto the
handle (1) in the correct positions.
Attach the cable (9) to the handle (1) with the clips (10) provided.
Route the cable (9) correctly in the positions ßx on the lower mounting bracket on the deck.

To assemble the grass box [Fig. A5]:

Push the grass box handle (2) into the grass box cover (3) until the connections audibly engages.

OPERATION

DANGER! Risk of injury!
Cut injury when the product starts accidentally.

Wait for the blade to stop, disconnect the product from the mains and use gloves before you adjust or transport the product.

To connect the mower [Fig. O1/O2]:

DANGER! Electric shock!
To avoid damage to the mains cable (11), the mains cable (11) must be inserted into the cable lock (L).
Before you operate insert the mains cable (11) into the cable lock (L).

Form a loop in the mains cable (11), insert the loop into the cable lock (L) slot in the switchbox (12) and pull tight.
Connect the mains cable (11) into a 230 V mains socket.

To adjust the cutting height [Fig. O3/O4/O5]:

CAUTION! Do not use more than 3 cutting height spacers (13). The cutting height spacers (13) must only be fitted between the blade (14) and the fan (15). Do not fit the cutting height spacers (13) between the blade (14) and the blade bolt (16).

To remove the blade bolt (16), hold the fan (15) firmly and loosen the blade bolt (16) with the spanner (17) provided.
Remove the blade bolt (16), the blade (14), the cutting height spacers (13) and the fan (15).
Inspect for damage and clean as necessary.
Put the fan (15) on the product.
Make sure that the fan (15) is fully in place and the hole of the fan is inline up with the threaded hole.
Put the cutting height spacers (13) onto the fan (15).
Higher Cut – less cutting height spacers Lower Cut – more cutting height spacers Make sure that the pegs have located into the holes.
Put the blade (14) on by aligning the D-shaped holes onto the cutting
height spacers (13).
Make sure that the pegs have located into the holes on the blade.
Put the blade bolt (16) through the centre hole of the blade (14).
Tighten down the blade bolt (16) clockwise by hand.
Hold the fan (15) firmly and tighten the blade bolt (16) with the spanner (17) provided.

To start the mower [Fig. O6/O7]:

DANGER! Risk of injury!
Risk of injury if the product does not stop when you release the start levers.

Do not bypass the safety devices or switches. For example do not attach the start levers to the handle.

To start:
The product is provided with a two-handed safety device (start lever (18) and safety lock-off button (5)) to prevent the product from being turned on by accident.

There are two start levers (18) fitted. Either one has to be used to start.

Push the safety lock-off button (5) with one hand and pull the start
lever (18) with the other hand.
The mower starts.
Release the safety lock-off button (5).
To prevent a ring being cut in the lawn and to clear any residual grass, tilt the mower slightly. When the lawnmower has reached full speed gently lower it onto the lawn.

To stop:

Release the start lever (18).
The mower stops.

To empty the grass box [Fig. O8/O9]:

DANGER! Risk of physical injury!
Cut injury when the blade turns or the product starts accidentally.

Wait for the blade to stop, disconnect the product from the mains and use gloves before you put/remove the grass box.

Models with a transparent window (23) in the lid shows the filling level of the grass box (3). This should be cleaned after every lawn mowing.

Remove the grass box (3) by the grass box handle (2).
This will open the grass box lid (21).
Empty the grass box (3).
Replace the grass box (3). Make sure that it locates securely onto the deck fixing locations.
Close the lid.

Failure to fit the grass box (3) and grass box lid (21) correctly can cause poor collection of grass clippings.

Tips to use the mower [Fig. O10/O11]:

Mow twice a week during the growing season.
The lawn will suffer if more than a third of its length is cut at one time and this may also result in poor collection.
For the best results mow the outside edge of the lawn in a clockwise
direction first.
Start to mow the edge of the lawn nearest to the power point.
So the cable is laid out on the lawn you have already cut.
For best grass collection always mow in a straight line. Do not swing the lawnmower from side to side.
For the best cutting results mow in straight lines with an overlap of approximately 8 – 10 cm on each pass with the mower.
Do not overload the mower. To mow long thick grass may cause the motor speed to drop and you will hear a change in the motor sound.
If the motor speed drops you may overload the mower which may cause damage. When you mow in long thick grass a first cut with the cutting
height set higher will help reduce the load.
See To adjust the cutting height.

MAINTENANCE

DANGER! Risk of injury!
Cut injury when the product starts accidentally.

Wait for the blade to stop, disconnect the product from the mains and use gloves before you maintain the product.

To clean the mower:

DANGER! Risk of injury!
Risk of injury and risk of damage to the product.

Do not clean the product with water or with a water jet (in particular high- pressure water jet).

Do not clean with chemicals including petrol or solvents. Some can destroy critical plastic parts.

The airflow slots must always be clean.

To clean the underside of the mower [Fig. M1]:

The underside is easiest to clean after you mowed.

Lay the mower on its side carefully.
Clean the underside (19) by removing any grass build up with the spanner/ scraper tool (17).
Clean the blade (14) and the fan (15) with a soft brush (do not use sharp objects).

To clean the outside of the mower [Fig. M2]:

Clean the outside with a dry cloth.
Clean the airflow slots (20) with a soft brush (do not use sharp objects).

STORAGE

To put into storage:
The product must be stored away from children.

Disconnect the product from the mains.
Clean the mower (see 4. MAINTENANCE).
Store the mower in a dry, enclosed and frost-free place.

Storage positions [Fig. S1/S2]:

Push the lower handle (1) inwards from both sides simultaneously and
fold it forward.
Tilt the mower backwards to stand in the vertical storage position.
Wrap the mains cable (11) securely around the mains cable hooks (

Disposal: (in accordance with RL2012/19/EC)

The product must not be disposed of to normal household waste. It must be disposed of in line with local environmental regulations.

IMPORTANT!

Dispose of the product through or via your municipal recycling collection centre.

TROUBLESHOOTING

DANGER! Risk of injury!
Cut injury when the product starts accidentally.

Wait for the blade to stop, disconnect the product from the mains and use gloves before you troubleshoot the product.

To replace the blade:

DANGER! Risk of injury!
Cut injury when the blade turns and it is damaged, bent, out of balance or has chipped edges.

Do not use the mower when the blade is damaged, bent, out of balance or has chipped edges.
Do not regrind the blade.

The FLYMO spare parts are available from your FLYMO dealer or from the
FLYMO service.

Only use an original FLYMO blade:

FLYMO Replacement Blade for 30 cm:

Reference no. FLY094
Part no. 529370590

FLYMO Replacement Blade for 33 cm:

Reference no. FLY095
Part no. 529370790

FLYMO Replacement Blade for 36 cm:

Reference no. FLY096
Part no. 529370890

Replace the blade (see 3. OPERATION To adjust the cutting height).

Problem	Possible Cause	Remedy
Mower does not start	Mains cable is disconnected or damaged.	Connect the

mains cable or if necessary replace it.
Motor is blocked| Remove the obstacle
Motor is jammed and makes a noise| Motor is blocked| Remove the obstacle.
Cutting height is too low| Raise the cutting height.
Loud noises, the mower is rattling| Screws on motor, its fixing or on the mower chasing are loose.| Let the screws be tightened by an authorised specialist dealer.
Mower runs unevenly or vibrates strongly| Blade is damaged /worn or the blade mounting is released.| Replace the blader
Blade is very dirty| Clean the mower (see 4. MAINTENANCE). If this does not rectify the problem, replace the blade.
Poor grass collection| Lid is not correct in place.| Put the lid correct on the grass box.
Airflow slots are dirty.| Clean the mower (see 4. MAINTENANCE).
Not mowing in straight lines.| Mow in straight lines.
Lawn is not cleanly mowed| Blade is blunt or damaged.| Replace the blader.
Cutting height is too low.| Raise the cutting height.
Poor flotation| Underside of the mower is dirty.| Clean the underside of the mower
Cutting height is too low.| Raise the cutting height.
Fan is damaged.| Check and replace the fan.

If poor flotation persists, contact the local approved Service mCentre.

NOTE: For any other malfunctions please contact the FLYMO service department. Repairs must only be done by FLYMO service departments or specialist dealers approved by FLYMO.

TECHNICAL DATA

Electric Hover Lawnmowe| Unit| Value (30 cm)| Value (33 cm)| Value (36 cm)
---|---|---|---|---
Rated power| W| 1700| 1700| 1800
Mains voltage| V| 230| 230| 230
Mains frequency| Hz| 50| 50| 50
Speed of rotation cutting blade| R/min| 4200| 4200| 4200
Cutting width| cm| 30| 33| 36
Cutting height adjustment (4 positions)| mm| 10 – 30| 10 – 30| 10 – 30
Volume of grass box| l| 20| 20| 26
Weight| kg| 8.4| 8.4| 8.7
Sound pressure level LpA 1) Uncertainty kpA| dB (A)| 84
3| 83
3| 80
3
Sound power level LWA 2): measured/ guaranteed Uncertainty kWA| dB (A)| 92 / 96
3.9| 92 / 96
3.2| 92 / 96
3.2
Hand / arm vibration avhw 1) Uncertainty kvhw| m/s²| 1.5
1.5| 1.5
1.5| 1.9
1.5

Measuring process complying with: 1) EN 60335-2-77 2) RL 2000/14/EC

NOTE: The stated vibration emission value has been measured according to
a standardised test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of
exposure. The vibration emission value can vary during actual use of the electric power tool.

Please consult the supply authority, if necessary, that the equipment is connected only to a supply of an impedance no more than 0.354 Ω.
This maximum permissible system impedance at the interface point of the user’s supply is according to the test value of EasiGlide Plus 360V.

ACCESSORIES

FLYMO Replacement Blade for 30 cm| As replacement for blunt blade.| Reference no. FLY094 Part no. 529370590
---|---|---
FLYMO Replacement Blade for 33 cm| As replacement for blunt blade.| Reference no. FLY095 Part no. 529370790
FLYMO Replacement Blade for 36 cm| As replacement for blunt blade.| Reference no. FLY096 Part no. 529370890

SERVICE/WARRANTY

Warranty statement:

In the event of a warranty claim, no charge is levied to you for the services provided.

FLYMO grants a warranty for all original FLYMO new products for two years from the date of original purchase from the retailer, provided that the devices have been for private use only. This manufacturer’s warranty does not apply to products acquired second hand. This warranty includes all significant defects of the product that can be proved to be material or manufacturing faults. This warranty is fulfilled by supplying a fully functional replacement product or by repairing the faulty product sent to us free of charge; we reserve the right to choose between these options. This service is subject to the following provisions:

The product has been used for its intended purpose as per the recommendations in the operating instructions.
Neither the purchaser nor a third party has attempted to open or repair the product.
Only Original FLYMO replacement parts and wear parts have been used for operation.
Presentation of the receipt.

Normal wear and tear of parts and components (such as blades, blade fixing parts, turbines, light bulbs, V-belts /toothed belts, impellers, air filters, spark plugs), visual changes, wear parts and consumables are excluded from the warranty

This manufacturer’s warranty is limited to replacement and repair of products in accordance with the abovementioned conditions. The manufacturer’s warranty does not constitute an entitlement to lodge other claims against us as a manufacturer, such as for damages. This manufacturer’s warranty does not, of course, affect statutory and contractual warranty claims against the dealer/retailer.

The manufacturer’s warranty is governed by the law of the Federal Republic of Germany.

In case of a warranty claim, please return the faulty product, together with a copy of the receipt and a description of the fault, with postage paid to the service address.

Consumables:
The blade is a consumable and is not included in the warranty.

PRODUCT LIABILITY

In accordance with the German Product Liability Act, we hereby expressly declare that we accept no liability for damage incurred from our products where said products have not been properly repaired by a FLYMO-approved service partner or where original FLYMO parts or parts authorised by FLYMO were not used.

EC DECLARATION OF CONFORMITY

The undersigned hereby certifies as the authorised representative of the manufacturer, Husqvarna AB, 561 82 Huskvarna, Sweden, that, when leaving our factory, the unit(s) indicated below is /are in accordance with the harmonised EU guidelines, EU standards of safety and product specific standards.
This certificate becomes void if the unit(s) is /are modified without our approval.

Description of the product:	Electric Hover Lawnmower
Product type	EasiGlide Plus 300V

EasiGlide Plus 330V
EasiGlide Plus 360V
Article-Number| 970483601
970483701
970483801
EC-Directives| 2006/42/EC
2014/30/EC
2000/14/EC
2011/65/EC
Harmonised EN| EN ISO 12100
EN 60335-1
EN 60335-2-77
Deposited Documentation| GARDENA Technical Documentation, M. Kugler, 89079 Ulm
Conformity Assessment according to| 2000/14/EC Procedure: art. 14 Annex VI
Noise level: measured / guaranteed| 92 dB (A) / 96 dB (A)
Year of EC marking:| 2020