D r Lighting A04074-A04622 Bathroom Wall Light Instruction Manual
- June 13, 2024
- D r Lighting
Table of Contents
D r Lighting A04074-A04622 Bathroom Wall Light Instruction Manual
Item Number: A04074-A04622
WARNING (To reduce the risk of fire, electric shock, or injury to persons):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
B) Place the wall switch in the “OFF” position. -
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is Type B,Max 40W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
Before doing assembly and installation please prepare the needed tools as below picture
-
Ladder
-
Phillips head. flat blade screwdriver
-
Electrical tape
-
Pliers
-
Wire cutter/Stripper
PARTS INCLUDING
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Back plate (1)
- (F) Knob nut (2)
- (G) Socket (1)
- (H) Glass shade (1)
ACCESSORIES ENCLOSED
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
bGo to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
B. Place the wall switch in the “OFF” position. -
Make assembly
Step A1: Unscrew knob nuts (F) from mounting plate (D), then set aside
for the following steps.
Step A2: Secure mounting plate (D) to outlet box with mounting screws
(A).
Step A3: Make wire connections
Step A4: Align the holes in the back plate (E) with the pre-assembled
mounting screws, then attach the back plate (E) using the previously removed
knob nuts (F) . Hand tighten until snug.
Step A5: Install bulbs (Not included) (Please do not exceed the maximum
wattage recommended on the socket.) Screw the glass shade (H) onto the socket
(G).
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
| Connect Black or Red Supply Wire to: | Connect White Supply Wire to: |
|---|---|
| Black | White |
| *Parallel cord (round & smooth) | *Parallel cord (square & ridged) |
| Clear, Brown, Gold or Black without tracer | Clear, Brown, Gold or Black with |
tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other
than green) with silver conductor
*Note : When parallel wires (SPT I & SPT II) are used. The neutral wire
is square shaped or ridged and the other wire will be round in shape or smooth
(see illus.)
Twist wires together with plastic wire connector until tightly joined, and
wrap each connector with approved
electrical tape. Be sure that no wire strands are exposed and then carefully
tuck all wires into the outlet box.
Check everything is installed properly, then you could turn on the light. Enjoy!
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner
(such as mild and non-abrasive soap). Do not use abrasive materials such as
scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustration when ordering parts.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>