ROCKBOARD SO Power Block 12 IEC 12x Galvanically Isolated Instruction Manual
- June 1, 2024
- ROCKBOARD
Table of Contents
ISO POWER BLOCK 12 IEC
Manual
SO Power Block 12 IEC 12x Galvanically Isolated
DESCRIPTION
The Rock Board® ISO Power Block 12 IEC is a multi-power supply for effects pedals, designed with 12 isolated transformers and highly filtered 9V DC power slots and a single USB-slot:
- 4 x 9V DC (isolated); max. output 250 mA each
- 4 x 9V DC (isolated); max. output 500 mA each
- 4 x switchable slots (isolated) with 9V DC / 12V DC / 15V DC / 18V DC; each max. output 500 mA at 9V, 375 mA at 12V, 300 mA at 15V, 250 mA at 18V
- 1 x USB 5V; max output 2A
The Rock Board® ISO Power Block 12 IEC was designed for powe-ring up to 12
effects pedals simultaneously without any noise. The advanced filtering
technology and electrical isolation used in the DC power slots prevents high
frequency noise and hum loops. Built with short circuit protection for each
individual slot, connected effects pedals are protected in case of a short
circuit. With a designated LED for each power slot indicating the slot is
working correctly,
you can quickly identify any problems without losing power to the remaining
pedals.
POWER SUPPLY
The Rock Board® ISO Power Block 12 IEC is powered by an included 3-pole power
cord. It is rated for a voltage of 100V – 240V 50Hz/60Hz alternate current.
CAUTION: Please use only the included 3-pole power cord or one with
identical specifications to avoid overheating and damage to the unit.
CONNECTION AND USE
- Connect the included 3-pole power cord to the input socket of the ISO Power Block 12 IEC.
- Connect the power cord to the outlet, which is rated for a voltage output of 100V – 240V 50Hz/60Hz alternate current.
- Connect the included power cables to your effects pedals and the ISO Power Block 12 IEC.
Note: The manufacturer reserves the right to change these specifications
without notice.
IMPORTANT NOTES: Make sure to use only effects pedals with a polarity of
(-) center / (+) outside and with the correct input voltage, to prevent damage
to your effect pedals. Check that the current draw of your effects pedals does
not exceed the maximum current output of each slot and the max. total current
output.
INCLUDED ACCESSORIES
- 1 x 3-pole power cord, voltage 100 – 240V AC
- 12 x Rock Board Flat Power Cable, 60 cm – for connecting effects pedals
SPECIFICATIONS
- 4 x 9V DC (isolated); max. output 250 mA each
- 4 x 9V DC (isolated); max. output 500 mA each
- 4 x switchable slots (isolated) with 9V DC / 12V DC / 15V DC / 18V DC; each max. output 500 mA at 9V, 375 mA at 12V, 300 mA at 15V, 250 mA at 18V
- 1 x USB 5V; max; max output 2A
- Individual status LEDs and short circuit protection for all power slots
- Input voltage of 100V – 240V 50Hz/60Hz 1.25A MAX
- Total output power: 30.6 W
- Dimensions: (L x W x H): 195 x 88 x 35 mm (7 43/64″ x 3 15/32″ x 1 3/8″)
- Weight: 608 g / 1.34 lbs
Note:
The ambient temperature of this product is below 25°C. This product is a Class
I device. When using a power cord set, use a product that complies with the
Electrical Appliance and Material Safety Act for Class I equipment.
USA DISTRIBUTION: Frames & Warwick Music USA, Inc.
info@rockboard.net | 629.202.6790
CHINESE DISTRIBUTION: Warwick Music
Equipment Trading (Shanghai) Co. Ltd.
| info@warwick.cn | +862134060110
NORTH EUROPEAN DISTRIBUTION: www.rockboard.de
info@rockboard.de |
www.w-distribution.de
www.facebook.com/warwickmusicdistribution
Headquarters: Warwick GmbH & Co. Music Equipment KG
08258 Markneukirchen / Germany | +49 (0) 37422 / 555 – 0
Family Owned • Solar Powered •
Sustainably Manufactured in a Green Environment
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>