ROCKBOARD PatchWorks Solderless Patch Cable System Instructions

June 6, 2024
ROCKBOARD

ROCKBOARD logo

ROCKBOARD PatchWorks Solderless Patch Cable System

ROCKBOARD PatchWorks Solderless Patch Cable System

Thank you for choosing the RockBoard® PatchWorks® Solderless Patch Cable System

The RockBoard® PatchWorks® Solderless Patch Cable System is an innovative system that allows you to create varying length, high-quality patch cables quickly and easily without any soldering required. This inventive design, developed in Germany, uses a two-part adjustable connector and saves valuable space on the pedalboard by allowing a straight or angled connection.
Using the high-quality audio cables and compact, gold plated ¼” plugs guarantees a short, clean signal path and pristine signal quality.

Preparation and Assembly

Step 1
Measure the desired cable length and add approximately 2 3/8″ for both connectors. For a patch cable of 6″ in length, you need about 8 3/8″ of cable.

ROCKBOARD PatchWorks Solderless Patch Cable System-1

Step 2
Cut the cable to the required length by using the included PatchWorks® Cable Cutter.

ROCKBOARD PatchWorks Solderless Patch Cable System-2

Step 3
Ensure that the cut surface is even and straight for a secure connection between the signal conductor, the braided shielding, and the appropriate contacts in the connector to avoid signal loss.

ROCKBOARD PatchWorks Solderless Patch Cable System-3

Step 4
Remove the screws from two PatchWorks® Solderless Plugs using the provided PatchWorks® TX8 wrench. Carefully set the screws in a safe place.

Step 5
Slip the rear part of the PatchWorks® Solderless 2-Piece Plug about 2″ over the cable.

ROCKBOARD PatchWorks Solderless Patch Cable System-5

The RockBoard® PatchWorks® Solderless Patch Cable System offers you the versatility of a straight or angled patch cable plug. With an adjustable housing system, you can craft the perfect signal route every time, regardless of jack placement on your effects pedals.

ROCKBOARD PatchWorks Solderless Patch Cable System-6

Assembling a straight PatchWorks® solderless plug

Step 1
Fit the cable into the front section of the two-part plug. Then turn the front part of the plug by 180 degrees around its axis while pressing slightly to ensure a good connection between plug and cable. The plug should now stick to the audio cable.

ROCKBOARD PatchWorks Solderless Patch Cable System-7

Step 2
Align the small rear unit of the two-part plug with the front unit of the plug. Slide the two components together and position the screw holes over each other.

ROCKBOARD PatchWorks Solderless Patch Cable System-8

Step 3
Screw the two parts together using the supplied PatchWorks® TX8 wrench. For a good grip and an optimal connection, the screw must be flush with the connector housing.

ROCKBOARD PatchWorks Solderless Patch Cable System-9

Repeat steps 6 through 8 to complete the other end of your PatchWorks® Solderless Patch Cable. Use a cable tester to check the conductivity of your patch cables before using them in your signal chain. Should there be a short or poor conductivity, disassemble the patch cable and check the surface on both sides. Should the connection be compromised, repeat the assembly steps from 1 to 5.
Enjoy your new RockBoard® PatchWorks® Solderless Patch Cable System!

Assembling an angled PatchWorks® solderless plug:

Step 1
Fit the cable into the front section of the two-part plug. Then turn the front part of the plug by 180 degrees around its axis while pressing slightly to ensure a good connection between plug and cable. The plug should now stick to the audio cable.

ROCKBOARD PatchWorks Solderless Patch Cable System-11

Step 2
Bend the cable by 90 degrees at the point where it protrudes from the front unit of the two-part plug. Align and fit the small rear part into the rotated front plug unit. Position both screw ho-les over each other.

ROCKBOARD PatchWorks Solderless Patch Cable System-12

Note: The manufacturer reserves the right to change specifications without notice at any time.

USA DISTRIBUTION: Framus & Warwick Music USA, Inc. | info@rockboard.net | 629.202.6790
CHINESE DISTRIBUTION: Warwick Music Equipment Trading (Shanghai) Co. Ltd. | info@warwick.cn | +862134060110
NORTH EUROPEAN DISTRIBUTION: www.rockboard.de | info@rockboard.de | www.w-distribution.de | www.facebook.com/warwickmusicdistribution
Headquarters: Warwick GmbH & Co. Music Equipment KG | 08258 Markneukirchen / Germany | +49 (0) 37422 / 555 – 0
Family Owned • Solar Powered • Sustainably Manufactured in a Green Environment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals