RINSEKIT 5 Gallon Rack Shower Instructions
- May 15, 2024
- RINSEKIT
Table of Contents
RINSEKIT 5 Gallon Rack Shower
FOR TIPS & TROUBLESHOOTING STEPS
www.RinseKit.com I 800-613-5764 I
info@RinseKit.com
SYSTEM
The unit will NOT automatically turn off if the water tank is empty. To avoid
damaging the unit, power off the RinseKit when the tank is empty.
MOUNTING
Inadequately secured loads and incorrectly mounted roof racks and accessory racks can come loose during travel and cause serious accidents! Therefore, installation, handling and use must be carried out in accordance with product and vehicle instructions. Check and tighten the mounting brackets periodically.
SOLAR HEATING
Your rack shower will heat the water inside on sunny days. Always check the
water temperature before l.lsing. The water tank may slightly bulge in hot
conditions. The bulging will not damage your unit. You can open the fill cap
to let the pressure out and the water tank will return to its original shape.
FREEZING CONDITIONS
For freezing conditions or long-term storage, drain all of the water out of
the tank, then keep the nozzle on until no water sprays out for 30 seconds.
WARRANTY
Your RinseKit comes with a warranty, for more information please visit www.RinseKit.com and click on the warranty tab. Note: receipt/proof of purchase will be required to file a warranty claim.
OTHER INFORMATION
- Ok to use with hot and cold water. 33° – 120° F
- BPA-free materials.
- Pump may vibrate when using mist spray setting.
- Only use clean water or you may clog the system.
- Keep upright to prevent leaking.
- Remove hose before driving.
PB NONSPILLABLE LEAD-ACID BATTERY 12.5V 5.0 Ah / 20HR
Scan QR code with the phone camera for instructional videos and more information.
Check out some of our other products at www.RinseKit.com
PARTS
The installation booklet covers the following information
- Attaching mounting brackets
- Mounting on roof rack
- Mounting on other areas
- Controls
- How to fill and use
- Charging
- Connecting to vehicle power
HOW TO INSTALL
A mounting system can be installed on any side.
Your Rack Shower comes with the T-cha n nel pre-installed on the bottom. To
move the mounting orientation simply remove the set screws and place T-cha n
nel on the desired side. Then reinsert set screws.
Your Rack shower includes different-sized T-bolts. Use the length that works
best for your application.
-
Insert T-bolts into the mounting bracket.
Repeat on the second bracket. -
Slide mounting brackets with Tbolts onto the end of the rack shower.
-
Slide both mounting brackets into desired locations.
ROOF RACK MOUNTING
Attach mounting bracket clamp. Then attach and tighten down the washer and locknut.
METAL SURFACE MOUNTING -
If you are mounting your Rack Shower directly to a metal surface you do not need the clamps.
-
When mounting your Rack Shower to a metal surface, just attach the washers and locknuts.
-
Using the included set screw tool, insert the set screws into the sides of the mounting bracket.
Keep covers in place when not in use to prevent water damage
HOW TO USE
-
To attach the hose open the control panel cover and press the hose quickly to connect it firmly to the adapter.
Remove hose and close the control panel when not in use.
-
Remove the water tank cap and add the water
Press power button
BATTERY COMES CHARGED
Red LED = Charging
Green & Red Blinking or Green LED Charged Note: May take several hours to
fully charge.
Red LED = Power
Ok to use the system while plugged in. Note: Will only charge to 12v
OPTIONAL POWER SUPPLY
Your Rack Shower includes a 12v plug for connecting directly to your vehicle’s 12v power supply. You can pull the plug through the opening located on the bottom of the Rack Shower.
Don’t forget to tag us on social media for a chance to be featured on our
RinseKit In Action page!
Use #RinseKit when sharing your post!
www.RinseKit.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>