GEL BLASTER SURGE Water Beads and Gel Ball Blasters User Manual
- June 9, 2024
- GEL BLASTER
Table of Contents
SURGE Water Beads and Gel Ball Blasters
User Manual
SURGE Water Beads and Gel Ball Blasters
STEP 1 – HYDRATE YOUR GELLETSTM !! IMPORTANT !!
Gullets must be submerged in water for at least two hours to fully expand to
size. They also need to have plenty of water to absorb (this is very
important) – you’ll know there was plenty of water if after 2 hours the
Gellets are still submerged in the water. Failing to completely hydrate
Gullets will cause your Gel Blaster’ to seem crappy.
Note: Make sure that the Gellets are prepared in an adequate sized
container. Store hydrated Gullets away from the elements and direct sunlight.
STEP 2 – CHARGE YOUR BLASTER
Use the provided USB-C cord to charge your blaster. Do not place your charging
blaster on any fabric surface during charging. Do not leave blaster charging
for an extended period of time, unplug it when the indicator light turns
green.
STEP 3 – FILL YOUR HOPPER
Fill your hopper with hydrated Gellets, make sure all water is drained from
the hopper before installing on your blaster.
STEP 4 – INSTALL HOPPER ONTO BLASTER
Screw the hopper into the SURGE feedneck. Then slide the feedneck onto the top
rail of the SURGE with the arrow pointing forward.
IMPORTANT – Make sure you slide the feedneck all the way forward until
you feel and hear a “click”. Failing to do so will cause your Gel Blaster
SURGE to misfire.
STEP 5 – OPTIONAL: INTERCHANGEABLE BARRELS
Your Gel Blaster currently comes with the Standard Barrel pre-installed
(175fps). To remove the barrel, use the Barrel Tool provided to unscrew the
barrel. You can then install your orange Reduced Velocity Barrel (100fps) for
a lighter blasting experience.
IMPORTANT – DO NOT OVERTIGHTEN YOUR BARREL!
STEP 6 – PROTECT YOUR EYES!
Put on your provided eye protection when using your Gel Blaster SURGE. Make
sure that others within firing distance are wearing eye protection too! Do not
shoot at people not wearing proper eye-wear.
STEP 7 – POWER ON AND HAVE A BLAST!
Switch between Single and Full-Auto with the Blaster Mode Switch.
WARNING:
Do not aim at eyes or face during play. Eyewear required for players and any
person within range. Do not modify blaster or gullets as it may lead to misuse
or injury. Use only with Gel Blaster Official Products. Read all instructions
before use. For Ages 14 and up
WARNING: The Gel Blaster is not intended to get wet. Don’t submerge your
Gel Blaster in water, and make sure your Gellets are fully strained of excess
water. This will protect the battery and circuitry within from failure or
potential overheating.
ONE GALLON OF WATER MAKES 10,000 GELLETST1
https://qrcodes.pro/4FxJlV
**NEED MORE GELLETS9 SCAN HERE!
»**
DO NOT RETURN TO THE STORE! If you’re not having the best Gel Blaster experience, email us at info@gelblaster.com or give us a call at 844-GELLETS, and we’ll personally take care of you!
HOW TO HYDRATE YOUR GELLETST™
- Pour one 10k Gillet pack (included) into a 1-gallon+ container (preferably with a lid)
- Add 1 gallon of water and wait at least 2hrs
- Strain your full-size Gullets of excess water
- Now you’re ready to go!
Fill your hopper and start blasting!
HOW TO STORE YOUR GELLETS
Keep hydrated Gullets ready for use whenever you want! Here’s how to properly
store hydrated Gullets.
- Add water to your container until all Pellets are submerged
- Seal the container with a lid
- Store in a cool place out of direct sunlight
MORE INFO ABOUT GELLETS
- Removing excess water is important, wet Gullets can damage your motor
- Avoid dehydration by making sure your Gullets are completely submerged in water when not in use
- With proper storage, standard hydrated Gullets are usable for up to 3 months!
FAQ & QUICK FIXES
My hopper & feed neck keep sliding off and won’t feed the Gullets into my Gel Blaster’?
– A. Please make sure your hopper is facing the right direction -the front
arrow (on your feed neck) should be facing toward your fins. If installed
correctly, the hopper and feed neck will dick & lock in place.
Q My Gullets aren’t shooting correctly and are rolling out of my Gel
Blaster’s barrel?
– A: This is caused by Gullets that aren’t full size. To make sure your
Gullets are fully hydrated, please allow your Gullets to be submerged in water
for a minimum of 2hrs before playing.
Q: My Gel Blaster® seems jammed?
– A: Your Gel Blaster® will rarely get jammed, but if this is the case, please
make sure to turn the ON/OFF switch to the OFF position. Now proceed to check
the tip and barrel of the Gel Blaster. If debris Is found in your Gel Blaster,
remove your hopper & feed neck and spray canned air directly into the barrel
forcing the debris to come out of the tip of the blaster. If the debris is
still stuck, use a pipe cleaner to force the remainder out of the tip of the
blaster. Never push the debris from the tip/front of the Gel Blaster towards
the back, that will only jam your Gel Blaster worse.
“The Gel Blaster/606E provides hours of playtime per charge using a powerful
lithium ion battery! But with that power comes the responsibility to take care
ol your battery Abuse, neglect, or misuse can ruin your battery, shorten your
playtime, or even cause a fired!Surge won’t take a charge, cease use and
charging! Contact sopport@gelblasters.com
@2022 Gel Blaster, Inc. Al Rights Reserved.
LIMITED WARRANTY, SUBROGATION WAIVER, WAIVER AND RELEASE, BINDING AGREEMENT
TO ARBITRATE, CLASS ACTION WAIVER
Gel Blaster, Lyle warrants this Gel Blaster for a period of one month from the
date of consumer purchase to be free from defects in material and
workmanship.Gd Blaster, Litigation under this warranty is limited to repair
outplacement of the purchased product only (although Gel Blaster, [LC may
determine to issue a refund, in its so and abusive discretion), and under no
circumstances shall Gel Blaster, LLC be liable for any loss, damage, injury,
cost of repair, consequential damages, incidental damages, or punitive,
treble, or exemplary damages of any kind in connection with the sale, use,
failure, or repair of any product purchased from Gel Blaster, Lie, even if
such damages are caused by the negligence of the released party, whether sole
or in combination with others. You hereby waive any claim by an insurance
carrier or other person or entity by way of subrogation, and you hereby assign
any and at such subrogation claims to Gel Blaster, U.C, Gel Blaster, LLC
disdains any warranty of fitness fora petiolar purpose and any implied
warranty of merchantabl4 Al impede warranties are hereby disdained, and you
agree that the only warranty provided by Gel Blaster, U.0 to you is the above.
Gel Blaster, Le’s liability for any and A claims arising out of or connected
with the Gel Raster shall I be limited to the amount paid by consumer for the
product plus the sum of $100.00.
You and Gel Blaster, LLC agree to mandatory, binding arbitration for any and
all claims or causes of action between the parties arising out of or in
connection with your purchase or use of the Gel Blaster, its accessories, or
otherwise with respect to any claims between you and Gel Blaster, LLC, The
arbitration shall take place under the rules of the American Arbitration
Association, Consumer Arbitration Rules, before a single arbitrator, The
Arbitration shall take place in Dallas, Texas. You understand and agree that
you are waiving your rights to a trial by jury. You agree that any claim you
have or may ever come to have against Gel Blaster, LLC must be submitted on an
individual basis, and you hereby waive the right to assert such claim
collectively, such as in a class or mass action. As a condition precedent to
filing arbitration, you must contact Gel Blaster, LLC with any claim or
dispute, which must be mediated before a mutually agreeable mediator in
Dallas, Dallas County, Texas.
You agree to the foregoing terms when you first charge or otherwise seek to
use your Gel Blaster or its accessories, NOTE: The transformer, power supply
or battery charger used with this product shall be regularly examined for
damage to the supply cord, plug, enclosure or other parts, and in the event of
damage, it shall not be used until the damage has been repaired. Always use
the Gel Blaster USB cord supplied with the product to charge.
The battery contained in this product is non-replaceable. The supply terminals
are not to be short-circuited.
Gel Blaster
5000 Plaza on the Lake Austin,
TX 78746 844-GELLETS
www.gelblastericom/patents
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>