BENY TS01 Tire Inflator Instruction Manual

TS01 Tire Inflator
Instruction Manual

Model: TS01
Read this manual carefully before use and keep it for future reference.

PRODUCT OVERVIEW

1. LCD Screen
2. Light button
3. “+” button
4. Power button
5. “_” button
6. Mode button| 7. LED light
8. Air outlet
9. USB output port
10. 12v DC Vehicle Power Supply
11. Type-C input port
12. LED light strip
---|---

PACKAGE CONTENTS

Carefully check the package contents. If anything is missing or damaged, please contact online customer service for support.

TECHNICAL SPECIFICATIONS

HOW TO USE AIR COMPRESSOR

Step 1. Remove the valve cap and connect the air tube to the inflator’s air outlet by rotating clockwise.

Step 2. Press to turn on the air pump.

Step 3 . Press to choose a mode. Detecting the current pressure and setting the target pressure value.

Step 4. Press to inflate.

DISPLAY AND BUTTONS

Modes and default units

Default tire pressure values in various modes

NOTE:

• Each mode has a default unit. Long press the Mode Button for 3 seconds to switch the current unit between the 4 unit options(BAR, PSI, and KPA, Kg/c㎡).

Button Functions

| • Long press the Power Button to turn on the inflator.
---|---
• Short press the Power Button to start inflating.
• In the power-on state, long press the Power Button to turn off the inflator.
| • After the mode is set, press the Plus Button to increase the presetpressure value.
| • After the mode is set, press the Minus Button to decrease the presetpressure value.
| • Press the Light Button to switch between Iluminator, SOS Signal, and Strobe.
| • Short press the Mode Button to switch modes.
• Select the correct pressure value before inflating.
• Long press the Mode Button to switch the unit between KPA, PSI, Kg/cm² and BAR.
| • Press and hold the Mode and Plus/Minus buttons together for 3 secondsto reset the system.

LIGHTING

• Press once and LED light is always on (3 watts).
• Press 2 times to switch the LED light to strobe.
• Press 3 times to LED light strip with weak gear (2 watts).
• Press 4 times to LED light strip with strong gear (5 watts).
• Press 5 times and the LED light strip to SOS.
• Finally click to turn off the LED light.|
---|---

Notice:
The LED light has a memory function. If a certain state remains for more than 10s, press the LED light button to turn off all the lights directly. The next time the light is turned on, it will be the light when it was turned off last time.

PRODUCT CHARGING GUIDE

With Wall Charge

1. Plug the wall charger into the universal socket.
2. Plug the end of the wall charger into the Type-c input port of the product.

With an External Power Supply

1. Plug the Type-C cable into the Type-C Port of the device.
2. Plug the other end of the Type-C cable into an external power supply.

With Power Cord

1. Plug the Power Cord into the input port of the device.
2. Plug the Power Cord into the cigarette adapter of your car.

AIR PRESSURE REFERENCE TABLE

American valve
(on the air tube)| | Motorcycle tires| 1.8 – 3.0 BAR
Car tires| 2.2 – 2.8 BAR
Presta valve adapter| | 12, 14, 16-inch bicycle tires| 30 – 50 PSI
20, 22, 24-inch bicycle tires| 40 – 50 PSI
26, 27.5, 29-inch mountain bike tires| 45 – 65 PSI
Electric scooter tires| 40 – 50 PSI
700c road bike clincher tires| 100 – 130 PSI
700c road bike tubular tires| 120 – 145 PSI
Ball needle adapter| | Basketball| 7 – 9 PSI
Soccer ball| 8 – 16 PSI
Volleyball| 4 – 5 PSI
Football| 12 – 14 PSI
Nozzle adapter 1| | Swimming ring| /
Balloon| /
Nozzle adapter 2| | Rubber boat| /

TROUBLESHOOTING

Slowly flashing green indicator| The power of the product is too low, and please recharge the product.
---|---
Red indicator| The connection timed out, and Please reconnect the clamps.
Flashing Red indicator| The temperature exceeds 65 + 5C. Remove the smart clamp until the indicator resumes flashing red and green alternately.
Other| Please feel free to contact us via ecservice@zibeny.com with details of the issue.

SAFETY INSTRUCTIONS

• Keep a safe distance between the body and the product while inflating or starting. After running for a long time, the temperature of the junction between the air tube and the main body may become very high.
  To avoid burns, do not touch.

• Please don’t leave it for prolonged periods in a hot car. Overheating, damage, or water may increase the risk of built-in lithium battery fire or explosion.

• Please store the product in a dry environment of -20℃~60℃, away from particulate matter and dust.
  Don’t wash the product with water.

• Long-time storage of the product may decrease the effectiveness of the battery. Charge the inflator at least once every three months to maintain its performance.

• Please use a certified 5V/3A adapter and the included charging cable to charge this product.

• This inflator is equipped with short-circuit protection, DO NOT connect its USB-A port to its USB-C port.

FAQ

1. Why is the product so slow to inflate when I first use it?
During the long transportation process, the battery charge may disappear. Please fully charge the battery before use.

2. What should I do if the product does not turn on?
Make sure the power switch is in the on position. Check that the jump starter is fully charged.
Recharge the unit if necessary. Make sure a proper polarity cable connection has been established.
If it still doesn’t work, please contact us via ecservice@zjbeny.com as soon as possible.

3.What if the USB port is not charging?
Make sure the product is charged. Check the connection between the USB port and the device.
Check if the charging cable is faulty.

WARNING

This product is for 12-Voltage vehicle (equipment) batteries. It may be dangerous if used with other types of batteries.Read and understand the safety instructions before using the jump starter.Fail to follow the safety instructions may cause damage to the jump starter, and may also result in electric shock, explosions，fire,property damage, and personal injury.

TS03
Jump Starter & Time Inflator

Model: TS03
Read this manual carefully before use and keep it for future reference.

PRODUCT OVERVIEW

1. LCD Screen
2. Light button
3. “+” button
4. Power button
5. “_” button
6. Mode button| 7. 12V DC port
8. LED light
9. Air outlet
10. USB output port
11. Type-C input port
12. LED light strip
---|---

PACKAGE CONTENTS
Carefully check the package contents. If anything is missing or damaged, please contact online customer service for support.

TECHNICAL SPECIFICATIONS

HOW TO USE JUMP STARTER

Step 1. Remove the valve cap and connect the air tube to the inflator’s air outlet by rotating clockwise.

Step 2. Connect the Red clamp to the positive electrode ( + ) of your vehicle battery and the Black Clamp to the negative one ( – ).

Step 3. Start your vehicle. If the engine is not successfully started, disconnect it to wait for at least 1 min and then try again.

Step 4. When the vehicle is started, remove the jumper cables from your car battery and the jump starter within 30 seconds.

HOW TO USE AIR COMPRESSOR

Step 1 . Remove the valve cap and connect the air tube to the inflator’s air outlet by rotating clockwise.

Step 2. Press to turn on the air pump.

Step 3 . Press to choose a mode. Detecting the current pressure and setting the target pressure value.

Step 4. Press to inflate.

DISPLAY AND BUTTONS

Modes and default units

Default tire pressure values in various modes

NOTE:

• Each mode has a default unit. Long press the Mode Button for 3 seconds to switch the current unit between the 4 unit options(BAR, PSI, and KPA, Kg/c㎡).

Button Functions

| • Long press the Power Button to turn on the inflator.
---|---
• Short press the Power Button to start inflating.
• In the power-on state, long press the Power Button to turn off the inflator.
| • After the mode is set, press the Plus Button to increase the presetpressure value.
| • After the mode is set, press the Minus Button to decrease the presetpressure value.
| • Press the Light Button to switch between Iluminator, SOS Signal, and Strobe.
| • Short press the Mode Button to switch modes.
• Select the correct pressure value before inflating.
• Long press the Mode Button to switch the unit between KPA, PSI, Kg/cm² and BAR.
| • Press and hold the Mode and Plus/Minus buttons together for 3 secondsto reset the system.

LIGHTING

• Press once and LED light is always on (3 watts).
• Press 2 times to switch the LED light to strobe.
• Press 3 times to LED light strip with weak gear (2 watts).
• Press 4 times to LED light strip with strong gear (5 watts).
• Press 5 times and the LED light strip to SOS.
• Finally click to turn off the LED light.|
---|---

Notice:
The LED light has a memory function. If a certain state remains for more than 10s, press the LED light button to turn off all the lights directly. The next time the light is turned on, it will be the light when it was turned off last time.

PRODUCT CHARGING GUIDE

With Wall Charge

1. Plug the wall charger into the universal socket.
2. Plug the end of the wall charger into the Type-c input port of the product.

With an External Power Supply

1. Plug the Type-C cable into the Type-C Port of the device.
2. Plug the other end of the Type-C cable into an external power supply.

With Power Cord

1. Plug the Power Cord into the input port of the device.
2. Plug the Power Cord into the cigarette adapter of your car.

AIR PRESSURE REFERENCE TABLE

American valve
(on the air tube)| | Motorcycle tires| 1.8 – 3.0 BAR
Car tires| 2.2 – 2.8 BAR
Presta valve adapter| | 12, 14, 16-inch bicycle tires| 30 – 50 PSI
20, 22, 24-inch bicycle tires| 40 – 50 PSI
26, 27.5, 29-inch mountain bike tires| 45 – 65 PSI
Electric scooter tires| 40 – 50 PSI
700c road bike clincher tires| 100 – 130 PSI
700c road bike tubular tires| 120 – 145 PSI
Ball needle adapter| | Basketball| 7 – 9 PSI
Soccer ball| 8 – 16 PSI
Volleyball| 4 – 5 PSI
Football| 12 – 14 PSI
Nozzle adapter 1| | Swimming ring| /
Balloon| /
Nozzle adapter 2| | Rubber boat| /

TROUBLESHOOTING

Slowly flashing green indicator| The power of the product is too low, and please recharge the product.
---|---
Red indicator| The connection timed out, and Please reconnect the clamps.
Red indicator with beeps| 1. Check whether the smart clips are connected backward.
2. Check whether the red and black clamps are connected or connected to the same piece of metal.
3. Adjust the smart clamp to maximize the connection to the car battery terminals.
Flashing Red indicator| The temperature exceeds 65 + 5C. Remove the smart clamp until the indicator resumes flashing red and green alternately.
Other| Please feel free to contact us via ecservice@zjbeny.com with details of the issue.

SAFETY INSTRUCTIONS

• Keep a safe distance between the body and the product while inflating or starting. After running for a long time, the temperature of the junction between the air tube and the main body may become very high.
  To avoid burns, do not touch.

• Please don’t leave it for prolonged periods in a hot car. Overheating, damage, or water may increase the risk of built-in lithium battery fire or explosion.

• Please store the product in a dry environment of -20℃~60℃, away from particulate matter and dust. Don’t wash the product with water.

• Long-time storage of the product may decrease the effectiveness of the battery. Charge the inflator at least once every three months to maintain its performance.

• Please use a certified 5V/3A adapter and the included charging cable to charge this product.

• This inflator is equipped with short-circuit protection, DO NOT connect its USB-A port to its USB-C port.

FAQ

1. Why is the product so slow to inflate when I first use it?
During the long transportation process, the battery charge may disappear. Please fully charge the battery before use.

2.What should I do if the product does not turn on?
Make sure the power switch is in the on position. Check that the jump starter is fully charged.
Recharge the unit if necessary. Make sure a proper polarity cable connection has been established.
If it still doesn’t work, please contact us via ecservice@zjbeny.com as soon as possible.

3.What if the USB port is not charging?
Make sure the product is charged. Check the connection between the USB port and the device.
Check if the charging cable is faulty.

WARNING
This product is for 12-Voltage vehicle (equipment) batteries. It may be dangerous if used with other types of batteries.Read and understand the safety instructions before using the jump starter. Fail to follow the safety instructions may cause damage to the jump starter, and may also result in electric shock, explosions，fire,property damage, and personal injury.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>