NIEN BMCS-RF RF Module Motorized Cellular Shade Installation Guide

NIEN BMCS-RF RF Module Motorized Cellular Shade

Specifications

• Model: BMCS-RF
• Type: Motorized Cellular Shade RF Module

Product Usage Instructions

• Shade Installation:
  • Connect the 2 wires to the RF module.
  • Slide the RF module into the bottom rail from its side.
  • Slide the battery pack into the bottom rail.
  • Refer to the Setup & Operation section to operate the shade.
• Setup & Operation:
  • Power ON: Hold the shade button for 3 seconds and the green light will flash 4 times.
  • Power OFF: Hold the shade button for 3 seconds and the red light will flash 4 times.
• Pair Shades with a Remote:
  • The shades are already paired with the Remote Control. If needed, follow these steps to reassign the shades to another remote.
  • Press the button 3 times to enter Pairing mode. The green light will start flashing.
  • Hold SET for 3 seconds to enter Setup mode. The LED will start blinking.
  • The shade will move up and down to indicate successful pairing. The green light will stop flashing.
• Un-pair the Shade from Remote Control:
  • Hold any Group button, the shades assigned to the group will move up and down.
  • Press the button 3 times to enter Pairing mode. The green light will start flashing.
  • Hold SET to enter Setup mode. The LED will start blinking.
  • The shade will move up and down 2 times to indicate successful un-pairing. The green light will stop flashing.
• Setup Positions:
  • IMPORTANT! Please set up the positions of a single shade to avoid tampering with other shades assigned to the same group.
• Setup Top Position:
  • Move the shade to a desired Top position using the Remote.
  • Hold RESET for 1 second. Press OPEN to set the Top position.
• Setup Bottom Position:
  • Move the shade to a desired Bottom position using the Remote.
  • Hold RESET for 1 second. Press CLOSE to set the Bottom position.

FAQs

• Q: How do I pair shades with a new remote?
  • A: Follow the steps mentioned in the Pair Shades with a Remote section to pair shades with a new remote.
• Q: Can I un-pair a shade from the remote control?
  • A: Yes, refer to the Un-pair the Shade from Remote Control section for instructions on how to un-pair a shade from the remote control.
• Q: Why is it important to set up top and bottom positions for the full function of the shades?
  • A: Setting up top and bottom positions ensures the proper functioning of the shades, allowing them to operate smoothly and accurately.

Shade Installation

• Step 1 Connect the 2 wires to the RF module
• Step 2 Slide the RF module into the bottom rail from its side.
• Step 3 Slide the battery pack into the bottom rail.
• Step 4 Refer to the “Setup & Operation” section to operate the shade

Setup & Operation

• Shade
• Remote

Power ON / OFF

• Power ON
  • Hold the shade button for 3 seconds and the green light will flash 4 times.
• Power OFF
  • Hold the shade button for 3 seconds and the red light will flash 4 times.

Pair shades with a Remote

• The shades are already paired with the Remote Control, If needed, please follow the steps to re-assign the shades to another remote.

IMPOTANT! Please pair only one type of shade in the same remote.

• Press the button 3 times to enter Pairing mode. The green light will start flashing.
• Hold SET for 3 seconds to enter Setup mode. The LED will start blinking.
• The shade will move up and down to indicate successful pairing. The green light will stop flashing.
• Hold SET for 3 seconds to leave Setup mode. The LED will stop blinking. The remote will leave Setup mode after 20 seconds of inactivity.

Un- pair the shade from the Remote control

• Hold any Group button, the shades assigned to the group will move up and down.
• Press the button 3 times to enter Pairing mode. The green light will start flashing.
• Hold SET to enter Setup mode. The LED will start blinking.
• The shade will move up and down 2 times to indicate successful unpairing. The green light will stop flashing.
• Hold SET for 3 seconds to leave Setup mode. The LED will stop blinking. The device will leave Setup mode automatically after 20 seconds of inactivity.

IMPORTANT! Please set the positions of a single shade to avoid tampering with the positions of other shades assigned to the same group:

1. Pair the desired shade to a new remote, then set the positions via a new group, or
2. Power off the other shades in same remote, and set up the positions of the desired shade.

IMPORTANT! Top and Bottom positions must be set up for the full function of the shades.

Setup Top Position

• Move the shade to the desired Top position by Remote.
• Hold RESET for 1 second. The Group LEDs will start blinking.
• Press OPEN to set up the Top position.
• The shade will move up and down to indicate a successful setup.

Setup Bottom Position

• Move the shade to the desired Bottom position by Remote.
• Hold RESET for 1 second. The Group LEDs will start blinking.
• Press CLOSE to set up the Bottom position.
• The shade will move up and down to indicate a successful setup.

IMPORTANT! Please clear the positions of a single shade to avoid tampering with the limits of other shades assigned to the same group:

1. Pair the desired shade to any new group alone, and clear the positions via the new group, or
2. Power off the other shades in the same group, and clear the positions of the desired shade.

IMPORTANT! Top and Bottom positions must be set up for the full function of the shades.
IMPORTANT! Top, Middle, and Bottom positions must be set up for the full function of the D&N/TDBU shades.

Clear Top / Bottom Position

• Hold RESET for 1 second. The Group LEDs will start blinking.
• Hold OPEN to clear the Top position. Hold CLOSE to clear the Bottom position.
• The shade will move up and down 2 times to indicate successful clearing.

Specification

FCC

Safety Statement Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Industry Canada Equipment Standard for Digital Equipment (ICES) Canada

• This Class B digital apparatus complies with Canadian ICES 003. CAN ICES 3 (B)/NMB 3(B)

Innovation, Science and Economic Development Canada(ISED) Compliance Statement

This device complies with ISED’s license-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Model: BMCS RF

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>