sOmfy 1871025 Decoflex RTS Switch Instruction Manual
- June 5, 2024
- somfy
Table of Contents
DECO FLEX RTS SWITCH
Operating Instructions
DESCRIPTION
The DecoFlex RTS Switch Is a wifeless radio transmitter compatible with all Sorrily RTS Motors and externally mounted RTS receivers.
- Commands are transmitted by radio waves at 433.42 MHz.
- Power: 3V lithium battery. CR 2450 type
- Operating temperature: +51t/41*F to 1-401C104’F
- Range: Up to 65 FL
- Fits into standard Decora Wall Plates
This is a low voltage device that does not need to be mounted inside an electrical box.
PROGRAMMING
A. ADDING A DECO FLEX RTS WALL SWITCH – INITIAL INSTALLATION IMPORTANT:
Initial programming provides power only to the motor or receiver being
programmed
- Set the RTS Receiver or Motor into its Programming Mode (Refer to the installation instructions of the relevant RTS receiver or motor for this procedure).
- Select the Charnel to be memorized by pressing the appropriate button. The button will light. Refer to figure 1.
- Using a paperclip or similar device, briefly press the programming button (1-sec max) located on the DecoRex Switch
- The receiver motor will confirm the addition of the new DecoFtex Switch in their respective manners.
B. ADDING MULTIPLE DECOFLEX WALL SWITCHES
- Place the receiver or motor into programming mode by pressing and holding the programming button (for 3 sec.) of a Decoflex switch or Tells Transmitter that has been previously memorized. There is no need to access the external receiver for this operation.
- The receiver/motor will confirm the PROGRAMMING MODE in their respective manners.
- Select the Mat channel or RTS Switch to be memorized. Press the programming button it sec. max.) on the DecoRex RTS switch.
- The receiver/motor will confirm the addition of the new RTS Switch or Channel in their respective manners.
C. REMOVING A DECOFLEX RTS SWITCH FROM THE MOTOR OR RECEIVER’S MEMORY
- Place the receiver or motor into programming made by pressing and holding the Me programming button (for 3 sec.) of a DecoRex RTS Switch Of Teta Transmitter that has been previously memorized II should NOT be the one to be removed from memory.
- The receiver/motor will confirm the PROGRAMMING MODE in their respective manners.
- Select the RTS Switch or Charnel to be removed from memory. Press the programming button (1-sec_ max) on the RTS switch.
- The receiver/motor will confirm the removal of the RTS Switch or Channel in their respective manners.
OPERATION
- Select the channel of the window treatment to be operated by pressing the appropriate button. The button will light Refer to Figure 2.
- To raise the window treatment. press the UP button. Similarly. to lower the window treatment, press the DOWN button.
- To stop the window treatment at any time, simply press the STOP button.
Federal Communication Commission Interference Statement
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Industry Canada statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions: (1) This device may not cause
interference; and (2) This device must accept any interference, including
interference that may cause undesired operation of the device. Le présent
appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes: 1) l’appareil ne doit pas produire de brouillage; 2) l’utilisateur
de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>